Paper describes the results of studies testing the creep resistance of two multi-principal element alloys, CoCrNi and CoCrFeMnNi.

The article reports on the shear deformation of a eutectic structured HEA and effect of precipitation on shear deformation, particularly Al₀.₇CoCrFeNi high-entropy alloy (HEA). A split-Hopkinson pressure bar (SHPB) was used to compress the hat-shaped specimens to study the local dynamic shear response of the alloy. The change in the width of shear bands with respect to precipitation and deformation rates was studied. The precipitation of L1₂ phase did not delay the formation of adiabatic shear bands (ASB) or affect the ASB width significantly, however, the deformed region around ASB, consisting of high density of twins in fcc phase, was reduced from 80 µm to 20 µm in the stronger precipitation strengthened condition.

In this article the time-dependent plastic deformation behavior of two refractory high entropy alloys was investigated, namely HfTaTiVZr and TaTiVWZr. These alloys are based on reduced activity metals from the 4-5-6 elemental palette that would allow easy post-service recycling after use in nuclear reactors. The creep behavior was investigated using nano-indentation over the temperature range of 298 K to 573 K under static and dynamic loads up to 5 N.

Article describes a study where laser surface engineering was successfully used to engineer a nano carbide composite coating on a low carbon steel substrate.

Article describes development of an ultrafine-grained magnesium alloy with an extraordinary strength and ductility combination, exceptional high specific strength, zero yield strength asymmetry and excellent high strain rate superplasticity.

An introduction to a series of research articles submitted on the topic of "Catalysts for Clean Energy Conversion and Storage".

Article discusses a novel eutectoid nano-lamellar (FCC + L12)/(BCC + B2) microstructure that has been discovered in a relatively simple Al0.3CoFeNi high entropy alloy (HEA) or complex concentrated alloy (CCA).

Article presents an in-depth discussion of liquid crystal blue phases (BPs).

Data management plan for the grant, "CAREER: Manufacturing of Mechanically Stable Nanoporous Ceramic Structures Via Selective Infiltration of Polymer Templates." This Faculty Early Career Development (CAREER) grant from the National Science Foundation supports fundamental research to elucidate a new strategy of manufacturing nanoporous ceramic structures with controllable structure and composition and programmable mechanical stability. The specific goal of this research is to discover processing-structure-property relationships in ceramic coatings and heterostructures by providing fundamental insights on the mechanism of liquid phase swelling-based infiltration of spin-coated polymer templates with inorganic precursors and defining the rules that control the resulting structure and, thus, access to various materials surfaces and interfaces.

Data management plan for the grant "Charge Transport in Two-Dimensional Materials Based Integrated Flexible Energy System."

This article reports the design, fabrication, and characterization of an all inkjet-printed field-effect transistor (FET).

Article presents the large scale synthesis of solution-processed 2D (CH₃(CH₂)₃NH₃)₂(CH₃NH₃)ₙ − 1PbₙI₃ₙ + 1 (n = 2, 3, and 4) perovskites, a family of layered compounds with composition-tunable bandgap, where inkjet printing was used to fabricate heterostructure, flexible photodetector devices. The flexible, inkjet-printed perovskite 2D heterostructures have significant potential for optoelectronic devices, which can enable broad possibilities with compositional tunability and versatility of the organohalide perovskites.

This article reports on a study where 2D TMDs (MoS₂ and WS₂) and the 3D allotrope of carbon and graphite were incorporated into acrylonitrile butadiene styrene (ABS) and polyethylene terephthalate glycol (PETG) matrices in order to form polymer matrix composites (PMCs). The multipronged analysis described in this study was motivated by the purpose to fuse together topics of low-cost, additive manufacturing with 2D layered materials, and studying their ensuing mechanical and tribological properties.

Article reporting on the inkjet printed, direct contact study of solution-processed, 2D perovskite-based photodetectors (PDs) formed on flexible PI substrates. Silver (Ag) and graphene (Gr) inks have been engineered to serve as efficient electrical contacts for solution-processed two-dimensional (2D) organo-halide (CH3(CH2)3NH3)2(CH3NH3)n−1PbnI3n+1 (n = 4) layered perovskites, where all inkjet-printed heterostructure PDs were fabricated on polyimide (PI) substrates.

This article presents dispersions of WS₂ and h-BN using cyclohexanone and terpineol as the solvent to subsequently print prototype capacitive nanodevices.

Article exploring phonon dynamics in mechanically exfoliated two-dimensional WSe₂ using temperature-dependent and laser-power-dependent Raman and photoluminescence (PL) spectroscopy. The work reported sheds fundamental insights into the evolution of phonon dynamics in WSe₂ and should help pave the way for designing high-performance electronic, optoelectronic and thermoelectric devices in the future.

This article describes the synthesis of indium tin oxide (ITO) thin films using solgel processing with a mixture of InCl₃, methanol, and SnCl₂, where the solutions were spin coated onto glass substrates. The combined architecture of black phosphorus on ITO thin films shows promise in its use for transparent electronics, which can also serve as a stepping stone for future solar cell platforms.

Data management plan for the grant, "Self-powered Wireless Sensors and Interfaces for UAVs." Self-powered wireless sensors acting as nanogenerators can not only harvest ambient environment energy during the flight but also are capable of wirelessly monitoring pressure, temperature and other parameters to make the UAV truly an intelligent transportation system (ITS). This proposal requests the acquisition of a Mask Aligner to pattern such self-powered sensors with nano-antenna structures for wireless communication. The addition of the proposed system will enable researchers to study novel 2D materials as self-powered sensors and actuators. The proposed infrastructure would allow the development of smart, autonomous mobility systems with breakthroughs in intelligent technologies, research and workforce preparation.

Article on the implementation of liquid exfoliation to inkjet-print two-dimensional (2D) black phosphorous (BP) and molybdenum disulfide (MoS₂) p–n heterojunctions on a standard indium tin oxide (ITO) glass substrate in a vertical architecture. The authors also compared the optical and electrical properties of the inkjet-printed BP layer with that of the MoS₂ and the electrical properties of the mechanically exfoliated MoS₂ with that of the inkjet-printed MoS₂.

Data management plan for the grant "Process and Materials Development for Additive Manufacturing (AM) of Tungsten-Based Alloys with Superior High Temperature Performance and Good Room Temperature Ductility." Research on CALPHAD simulations will be conducted to optimize the chemical composition of tungsten based alloys towards 3D printability while boosting mechanical performance through solid solution and dispersion strengthening. This will followed by powder prototyping to validate the simulation results experimentally and to finalize the chemical composition of interest. Process parameter optimization and post-process heat treatment design will help to achieve optimal low-to-high temperature mechanical properties. Mechanical testing and microstructural characterization will be performed to establish process-microstructure-property relationships.

Data management plan for the research project "Enabling Multi-scale Modeling by Deciphering Fundamental Mechanisms Underlying Phase Stability, Deformation and Oxidation in Refractory Complex Concentrated Alloys (RCCAs) and Intermetallics."

This article combines machine learning (ML), finite element analysis (FEA), and empirical experiments to develop data-driven models that characterize interfacial mechanical properties precisely. It also provides a code package containing trained ML models, allowing other researchers to establish T–S relations for different material interfaces.

Article exploring friction stir alloying (FSA) to tune the microstructure and a composition of a TWIP high-entropy alloy by adding Ti, and thus activating site-specific deformation mechanisms that occur concomitantly in a single alloy. This approach presents a novel microstructural architecture to design alloys, an approach that combines and optimizes local compositions such that multiple deformation mechanisms can be activated to enhance engineering properties.

Article studying material response under dynamic short duration-high temperature oxidation.