We determine details of the adsorption of O{sub 2} or N{sub 2} in Na{sup +} and Li{sup +} exchanged zeolites by way of their effect on coadsorbed H{sub 2} molecules using inelastic neutron scattering (INS) techniques. Adsorption site occupancies are deduced with the aid of MC simulations. The expected stronger binding of N{sub 2} (compared with O{sub 2}) in LiX is evident in coadsorption spectra of N{sub 2} or O{sub 2} with H{sub 2}.

Recent microfabrication technologies based on LIGA (German acronym for Li thographe, G alvanoformung, und A bformung) have been applied to build high-aspect-ratio, metallic or dielectric, planar structures suitable for high frequency rf cavity structures. The cavity structures would be used as parts of linear accelerators, microwave undulators, and mm-wave amplifiers. The microfabrication process includes manufacturing of precision x-ray masks, exposure of positive resist by x-rays through the mask, resist development, and electroforming of the final microstructure. Prototypes of a 32-cell, 108-GHz constant impedance cavity and a 66-cell, 94-GHz constant-gradient cavity were fabricated using the synchrotron radiation sources at APS. Preliminary design parameters for a 91- GHz modulator klystron along with an overview of the new technology are discussed.

Some thermodynamic relations about an equilibrium Chapman-Jouguet (CJ) state are obtained. Relations for sound speeds in the wave velocity-particle velocity plane are derived. A relation between the slope of the sound speed in this plane and the asymptotic slope of the Hugoniot is suggested.

The authors describe a new technique for driving thick flying plates to high velocities without spall and with excellent flatness over a uniformly large area.

This paper presents estimates of the full cycle energy and emissions impacts of light-duty vehicles with tripled fuel economy (3X vehicles) as currently being developed by the Partnership for a New Generation of Vehicles (PNGV). Seven engine and fuel combinations were analyzed: reformulated gasoline, methanol, and ethanol in spark-ignition, direct-injection engines; low sulfur diesel and dimethyl ether in compression-ignition, direct-injection engines; and hydrogen and methanol in fuel-cell vehicles. The fuel efficiency gain by 3X vehicles translated directly into reductions in total energy demand, petroleum demand, and carbon dioxide emissions. The combination of fuel substitution and fuel efficiency resulted in substantial reductions in emissions of nitrogen oxide, carbon monoxide, volatile organic compounds, sulfur oxide, and particulate matter smaller than 10 microns, particularly under the High Market Share Scenario.

Gamma-ray emission probabilities of {sup 235}U and {sup 238}U have been studied extensively. While the gamma-ray emission probabilities for {sup 235}U and are well known, the emission probabilities for {sup 238}U differ widely from one study to another. This study indicates that one of the causes of the large discrepancies in the studies may be due to the true coincidence summing of many gamma rays from the decay of {sup 238}U daughters. The intensities of some of the intense gamma rays of {sup 238}U compared with the others were reduced by as much as 16% when the 21-mm-thick U{sub 3}O{sub 8} samples were moved from 15 cm to putting them in contact with the detector. With better knowledge of the gamma-ray emission probabilities and understanding the summing effects of specific gamma rays, the isotopic concentration of uranium can be better analyzed. The results of the isotopic analysis using fixed energy response function analysis with multiple efficiencies (FRAM) with the summing correction are presented in this paper.

The neutronics design of pulsed spallation neutron sources can be difficult when considering the fact that multiple instruments view the same moderator. Typically, the moderator design is a compromise between the required resolution for one instrument and the maximum intensity desires of another instrument. At the Manuel Lujan, Jr., Neutron Scattering Center (MLNSC), a recent target redesign has offered the opportunity to design a moderator for a Laue diffractometer with few other requirements. Detailed time and energy spectra were calculated for a variety of moderator decoupling options. The purpose of this summary is to document the neutronics calculations required for this source-instrument matching process.

The authors report on the results of finite-difference simulations of regional seismic wave propagation from a 1995 explosion at the Chinese test site at Lop Nor and from the recent Indian test. These simulations provide insight into variations in explosion seismograms recorded for these events. Previous modeling efforts by App et al., 1996, and Jones et al., 1998, have shown that many features in seismograms from explosions and earthquakes received at various stations surrounding Lop Nor can be reproduced with simple descriptions of the geologic structure along each path. However, differences in detail between simulations and the earthquake-like seismograms recorded at Station TLY in the Baikal Rift for the Lop Nor explosion have motivated further study of propagation effects. Differences between the TLY data and the simulations indicate that the use of homogeneous materials within the basins, crust, and mantle is too simplistic to capture some of the important features of the observed seismograms. Current efforts involve simulations in which 1-D and 2-D lithosphere models are merged to mimic gradients and 2-D structure, features which produce Rayleigh-wave dispersion and an improved agreement in group velocity curves. Source models have been modified to include a component of tectonic release during the …

The next giant leap for mankind will be the human exploration of Mars. Almost certainly within the next thirty years, a human crew will brave the isolation, the radiation, and the lack of gravity to walk on and explore the Red planet. However, because the mission distances and duration will be hundreds of times greater than the lunar missions, a human crew will face much greater obstacles and a higher risk than those experienced during the Apollo program. A single solution to many of these obstacles is to dramatically decrease the mission duration by developing a high performance propulsion system. The gas-core nuclear rocket (GCNR) has the potential to be such a system. The authors have completed a comparative study of the potential impact that a GCNR could have on a manned Mars mission. The total IMLEO, transit times, and accumulated radiation dose to the crew will be compared with the NASA Design Reference Missions.

In this paper, a support and preload system is presented in which the frequencies and damping of the test article are affected by the stiffness and damping of the supporting structure. A dynamic model is derived for the support system that includes the damping as well as the mass and stiffness of the supports. The frequencies, damping, and mode shapes are compared with the experimentally determined parameters. It is shown that for a seemingly simple support system, deriving a predictive model is not a trival task.

The photovoltaic (PV) industry is rapidly beginning to recognize the market potential of the buildings sector. New PV-for-buildings products have recently become commercially available, and numerous products that are under development will be introduced within the next 5 years. To ensure that these new products will be adopted and used in common building practices, the PV industry should recognize and address important buildings industry issues. These issues include building codes and standards, after-market servicing, education, and warranties and insurance policies. Photovoltaic systems are also still very expensive. The simplest method for increasing their value for a building is to decrease the building's electrical loads through energy efficiency and conservation. Meeting these goals can only be accomplished through partnerships with the U.S. Department of Energy (DOE), private industry, and public institutions.

This study considers a composite-to-steel tubular lap joint in which failure typically occurs when the adhesive debonds from the steel adherend. The same basic joint was subjected to compressive and tensile axial loads (single-cycle) as well as bending loads (fatigue). The purpose of these tests was to determine whether failure is more dependent on the plastic strain or the peel stress that develops in the adhesive. For the same joint, compressive and tensile loads of the same magnitude will produce similar plastic strains but peel stresses of opposite signs in the adhesive. In the axial tests, the tensile strengths were much greater than the compressive strengths - indicating that the peel stress is key to predicting the single-cycle strengths. To determine the key parameter(s) for predicting high-cycle fatigue strengths, a test technique capable of subjecting a specimen to several million cycles per day was developed. In these bending tests, the initial adhesive debonding always occurred on the compressive side. This result is consistent with the single-cycle tests, although not as conclusive due to the limited number of tests. Nevertheless, a fatigue test method has been established and future tests are planned.

A methodology for estimating the relative probabilities of different compromise paths for protected information by insider and visitor intelligence collectors has been developed based on an event-tree analysis of the intelligence collection operation. The analyst identifies target information and ultimate users who might attempt to gain that information. The analyst then uses an event tree to develop a set of compromise paths. Probability models are developed for each of the compromise paths that user parameters based on expert judgment or historical data on security violations. The resulting probability estimates indicate the relative likelihood of different compromise paths and provide an input for security resource allocation. Application of the methodology is demonstrated using a national security example. A set of compromise paths and probability models specifically addressing this example espionage problem are developed. The probability models for hard-copy information compromise paths are quantified as an illustration of the results using parametric values representative of historical data available in secure facilities, supplemented where necessary by expert judgment.

A few years after the Apollo flights to the Moon, it became clear that all of the existing theories on the origin of the Moon would not satisfy the growing body of constraints which appeared with the data gathered by the Apollo flights. About the same time, researchers began to realize that the inner (terrestrial) planets were not born quietly -- all had evidences of impacts on their surfaces. This fact reinforced the idea that the planets had formed by the accumulation of planetesimals. Since the Earth`s moon is unique among the terrestrial planets, a few researchers realized that perhaps the Moon originated in a singular event; an event that was quite probable, but not so probable that one would expect all the terrestrial planets to have a large moon. And thus was born the idea that a giant impact formed the Moon. Impacts would be common in the early solar system; perhaps a really large impact of two almost fully formed planets of disparate sizes would lead to material orbiting the proto-earth, a proto-moon. This idea remained to be tested. Using a relatively new, but robust, method of doing the hydrodynamics of the collision (Smoothed-Particle Hydrodynamics), the author and …

The design and fabrication of a four-vane RFQ to deliver a 100 mA CW proton beam at 6.7 MeV is described. This linac is an Oxygen-Free Electrolytic (OFE) copper structure 8 m in length and was fabricated using hydrogen furnace brazing as the joining technology.

Plasma flow velocity fluctuations have been directly measured in the high temperature magnetically confined plasma in the Madison Symmetric Torus (MST) Reversed-Field Pinch (RFP). These measurements show that the flow velocity fluctuations are correlated with magnetic field fluctuations. This initial measurement is subject to limitations of spatial localization and other uncertainties, but is evidence for sustainment of the RFP magnetic field configuration by the magnetohydrodynamic (MHD) dynamo. Both the flow velocity and magnetic field fluctuations are the result of global resistive MHD modes of helicity m = 1, n = 5--10 in the core of MST. Chord-averaged flow velocity fluctuations are measured in the core of MST by recording the Doppler shift of impurity line emission with a specialized high resolution and throughput grating spectrometer. Magnetic field fluctuations are recorded with a large array of small edge pickup coils, which allows spectral decomposition into discrete modes and subsequent correlation with the velocity fluctuation data.

The initial goal of the SNS project is to produce a 1 MW average beam of protons with short pulse lengths onto a neutron-producing target. The objective of the SNS RF system is to generate 117 MW peak of pulsed 805 MHz microwave power with an accelerated beam pulse length of 1.04 ms at a 60 Hz repetition rate. The power system must be upgradeable in peak power to deliver 2 MW average power to the neutron target. The RF system also requires about 3 MW peak of RF power at 402.5 MHz, but that system is not discussed here. The design challenge is to produce an RF system at minimum cost, that is very reliable and economical to operate. The combination of long pulses and high repetition rates make conventional solutions, such as the pulse transformer and transmission line method, very expensive. The klystron, with a modulating anode, and 1.5 MW of peak output power is the baseline RF amplifier, an 56 are required in the baseline design. The authors discuss four power system configurations that are the candidates for the design. The baseline design is a floating-deck modulating anode system. A second power system being investigated is the …

The Los Alamos ICF program has made several advances in learning what is required for ignition on NIF. This work continues to focus on beryllium--understanding why it appears less sensitive to DT ice roughness, the feed-out/feed-in phenomena, applying that understanding to new designs, performing experiments to confirm this mechanism, and studying the effects of joints in beryllium components.

The notion of perspective when supported in knowledge representation can allow the representation of multiple and varying points of view, some of which may even be inconsistent with one another. In an object-based knowledge representation methodology created and used by the authors, a perspective is defined by consolidating a number of objects and a number of those objects` associated attributes and methods into a view. This view can help partition a knowledge domain into separate portions. A separate portion represents an individual`s view of the knowledge domain. Representation of multiple and varying perspectives may add to the existing knowledge as well as reveal paths to additional knowledge. A simple example is presented where perspectives are used to represent game playing strategies and levels of expertise in those strategies. Players` perspectives are adapted and changed to provide additional knowledge and insight into further game playing strategies. Results show improvement in the playing of the games. Additionally, a more complex problem for applying these techniques is introduced.

A high temperature superconducting (HTS) current lead test facility using heat pipe thermal intercepts is under development at the Superconducting Technology Center at Los Alamos National Laboratory. The facility can be configured for tests at currents up to 1,000 A. Mechanical cryocoolers provide refrigeration to the leads. Electrical isolation is maintained by intercepting thermal energy from the leads through cryogenic heat pipes. HST lead warm end temperature is variable from 65 K to over 90 K by controlling heat pipe evaporator temperature. Cold end temperature is variable up to 30 K. Performance predictions in terms of heat pipe evaporator temperature as a function of lead current are presented for the initial facility configuration, which supports testing up to 200 A. Measurements are to include temperature and voltage gradient in the conventional and HTS lead sections, temperature and heat transfer rate in the heat pipes. as well as optimum and off-optimum performance of the conventional lead sections.

Enclosures for confinement of special nuclear materials (SNM) have evolved into the design of gloveboxes. During the early stages of glovebox technology, established practices and process operation requirements defined design criteria. Proven boxes that performed and met or exceeded process requirements in one group or area, often could not be duplicated in other areas or processes, and till achieve the same success. Changes in materials, fabrication and installation methods often only met immediate design criteria. Standardization of design criteria took a big step during creation of ``Special-Nuclear Materials R and D Laboratory Project, Glovebox standards``. The standards defined design criteria for every type of process equipment in its most general form. Los Alamos National Laboratory (LANL) then and now has had great success with Pu-238 processing. However with ever changing Environment Safety and Health (ES and H) requirements and Ta-55 Facility Configuration Management, current design criteria are forced to explore alternative methods of glovebox design fabrication and installation. Pu-238 fuel processing operations in the Power Source Technologies Group have pushed the limitations of current design criteria. More than half of Pu-238 gloveboxes are being retrofitted or replaced to perform the specific fuel process operations. Pu-238 glovebox design criteria are headed …

Transparency on warhead stockpiles, warhead dismantlement, and fissile material stockpiles in nuclear weapons states will become increasingly important in the move beyond START II toward lower quantities of warheads. Congressional support for further warhead reductions will likely depend on the degree of irreversibility, or in other words, the rapidity with which warhead inventories could be reconstituted. Whether irreversibility considerations can be satisfied will depend on monitoring dismantlement as well as constraining the available stockpile of fissile materials for possible refabrication into warheads. Measurement techniques designed to address the above problems will need to consider NPT Article 1 obligations as well as Russian and US classification regulations, which prohibit or restrict the transfer of nuclear warhead design information to other states. Classification considerations currently limit the potential completeness of future inspections of weapons materials. Many conventional international safeguards approaches are not currently viable for arms control applications because they would reveal weapons design information. The authors discuss a variety of technical measures that may help to improve transparence of warhead and fissile material stockpiles and may enable limited warhead dismantlement transparency.

The problem of Lamb waves propagation from small explosions in the atmospheric boundary layer are discussed. The results of lamb waves registrations from surface explosions with yields varied from 3 tons up to a few hundred tons (TNT equivalent) are presented. The source-receiver distances varied from 20 km up to 310 km. Most of the explosions were conducted during the evening and early morning hours when strong near-surface temperature and wind inversions existed. The corresponding profiles of effective sound velocity are presented. Some of the explosions had been realized with 15 minute intervals between them when morning inversion being destroyed. Corresponding transformation of Lamb waves was observed. The Korteveg-de Vrize equation to explain experimental data on Lamb waves propagation along earth surface is used.

Components made from PBX 9502, an insensitive high explosive formulated with triaminotrinitrobenzene (TATB) and Kel-F 800 binder, have been in service for nearly two decades. Since that time, samples have been destructively evaluated to determine if potential changes that might affect safety, reliability, or performance have occurred in the high explosive with time. Data from routine, historical testing is reported elsewhere. This paper focuses on specific tests conducted to evaluate the effects of natural aging on handling sensitivity (through the small-scale tests of Human Electrostatic Discharge, friction, and Drop Weight Impact), compressive strength, and thermal ignition. Also reported are the effects of a radiation environment on TATB. Small-scale sensitivity tests show no differences between aged and unaged material. Observed differences in compressive strength behavior are attributed to conditions of original material rather than aging effects. Thermal ignition by flame and laser methods showed no changes between aged and unaged material. Extreme levels of radiation are shown to have only minimal effects in explosive response tests. PBX 9502 is concluded, once again, to be a very stable material, aging gracefully.