Report discussing testing on a model of the proposed MX-1554A design to determine its stability and control characteristics in high speed flight. Information about the effect of speed brakes, tanks, and fences on the longitudinal characteristics is also provided.

Report presenting theoretical values of rocket performance parameters for two mixtures of liquid ammonia and hydrazine with flourine as oxidant for a variety of parameters. Parameters included are specific impulse, combustion chamber temperature, nozzle-exit temperature, equilibrium composition, mean molecular weight, characteristic velocity, coefficient of thrust, ratio of nozzle-exit area to throat area, specific heat at constant pressure, coefficient of viscosity, and coefficient of thermal conductivity.

"The rotating multicylinder method for in-flight determination of liquid-water content, droplet size, and droplet-size distribution in icing clouds is described. The theory of operation, the apparatus required, the technique of obtaining data in flight, and detailed methods of calculating the results, including necessary charts and tables, are presented" (p. 1).

Report presenting an investigation in the altitude test chamber to evaluate the performance of an axial-flow turbojet engine over a range of engine-inlet Reynolds number indices. Secondary effects of exhaust-nozzle flow coefficient, air-flow leakage, and inlet temperature should be considered before analyzing the effect of variations in engine-inlet Reynolds number index. Several minor design modifications proposed by the manufacturer did not produce any measurable improvement in engine performance.

From Introduction: "This paper will treat the problem in the suggested manner, beginning with the development of a suitable boundary condition to represent mathematically a homogeneous boundary which has the same flow characteristics, at a point in the flow sufficiently removed from the boundary as the actual physical boundary of alternate open and closed portions of the wall. Numerical results will be presented for circular tunnels with uniformly distributed around the circumference, for rectangular tunnels with uniformly distributed around the circumference, for rectangular tunnels with uniformly distributed slots in the top and bottom walls, for rectangular tunnels with the slot distribution determined by a transformation from a uniformly slotted circular tunnel, and for a two-dimensional tunnel. The results of this paper are derived on the basis of an incompressible potential flow."

"Tests on equivalent bodies of revolution of six configurations of the Consolidated Vultee Aircraft Corporation proposed supersonic bomber (Convair MX-1964) have indicated that it is possible to reduce the drag of the configuration by designing it to have a favorable area distribution. The method of NACA RM L53I22c to predict the peak pressure drag of a configuration on the basis of its area distribution gave generally good agreement with the subject models" (p. 1).

An analysis has been made of available experimental data to show the effects of most variables that are predominant in determining base pressure at supersonic speeds. Two dimensional bases and bases of bodies of revolution, restricted to turbulent boundary layers, are covered.

Calibrations of the Friez Aerovane, Wind Measuring Set AN/GMQ-11, manufactured by the Friez Instrument Division of the Bendix Aviation Corporation, were made in the Langley 300 MPH 7- by 10-foot tunnel at the request of the Signal Corps, U, S. Army. Two propellers snd two generators were tested through a speed range of 15 to 190 knots, The results indicated that at airspeeds greater than 80 knots the instrument indicated airspeeds higher than the tunnel airspeed..

From Introduction: "An investigation was conducted in an NACA Lewis altitude chamber to determine the altitude performance characteristics of a J47-25 axial-flow turbojet engine over a range of engine-inlet Reynolds number indices corresponding to altitudes from 18,000 to 54,000 feet and flight Mach numbers from 0.50 to 1.10. Reynolds number at a given corrected engine speed and is a function only of engine-inlet total pressure and temperature, was used instead of various set altitudes and flight Mach number combinations (reference 1). An example is included in the appendix to illustrate the method of obtaining conventional performance parameters for a given flight condition from the data such as presented herein."

Report presenting data obtained three single annular-type combustors with different combustor inlet-air pressure profiles over a range of engine speeds. Results regarding effect of changing combustor inlet-air pressure profile and hole geometry on combustor performance, performance of the prototype J40-WE-8 turbojet engine combustor, correlation of combustion efficiency with engine fuel-air ratio and combustion parameter, and comparison of several combustors from different turbojet engines are provided.

Memorandum presenting an investigation of the stability of several bodies of revolution having fineness ratios smaller than 1.0 and having rounded fronts and blunt bases. Free-drop tests were made in the vertical 20-foot free-spinning tunnel to determine the behavior of the various bodies in descent.

Report presenting an investigation in the transonic tunnel to determine the flow phenomena, pressure recovery, and external drag of a forward-located underslung air scoop mounted on a basic body of revolution with fineness ratio 11, which when cut off to provide an exit for the internal flow had a fineness ratio of 8. Results regarding the surface pressure distributions, drag, lift and pitching moment, and flow into the inlet on the modified model are provided.

Memorandum presenting minimum spark-ignition energies for 12 pure fuels measured at reduced pressure, and the data obtained were extrapolated to 1 atmosphere. Some of the fuels investigated included normal and cycloparaffins, olefins, carbon disulfide, and oxygenated compounds such as alcohol, ether, propylene oxide, and tetrahydropyran.

The structural damping in the torsion mode of vibration of a series of untwisted, laminated thin beams simulating propeller blades is presented. The number of lamination were varied, as well as the bonding material and the method of joining lamination. Application of the data to the calculation of the minimum flutter speed of thin propeller blades indicates that appreciable gains in the minimum flutter speed may be obtained for laminated blades using a Cycleweld bond.

Report presenting an investigation in the high-speed tunnel for a range of Mach numbers to determine the lateral control characteristics of a wing-fuselage combination with the wing quarter-chord line swept back 32.6 degrees, an aspect ratio of 4, a taper ratio of 0.6, and an NACA 65A006 section. Results regarding yawing-moment characteristics, spoiler-slot-deflector testing, and rolling-moment coefficient are provided.

Memorandum presenting tests made on a normal-shock inlet mounted as a scoop on a flat plate on which a turbulent boundary layer was generated. A boundary-layer-removal scoop was provided between the inlet and the plate and various amounts of the boundary layer were removed. Results regarding the main inlet, boundary-layer scoop, and an evaluation of results are provided.

Report presenting an investigation of the zero-lift-drag characteristics of nine symmetrical airfoils at a range of Mach and Reynolds numbers. Results regarding pressure and force data are also provided.

Report presenting an investigation to determine the effects of plan-form taper on the aerodynamic characteristics of a series of symmetrical, unswept wings with thicknesses of 8-percent chord. The wings were tested with four different bodies of revolution over a range of Mach numbers. Results regarding the lift, drag, pitching-moment, lift-curve slope, lift-drag ratio, and pitching-moment curve are provided.

Memorandum presenting an investigation of the effects of higher degrees of forming in biaxial stretch-forming of polymethyl methacrylate to about 50-percent strain. Sheets of commercial cast polymethyl methacrylate were hot-stretched approximately 100 and 150 percent, respectively, and tests were conducted on this material and on unstretched cotton material. Results regarding the standard tensile tests, stress-solvent crazing, surface abrasion tests, and x-ray diffraction patterns are provided.

Report presenting an investigation at Mach number 1.61 of the effects of chordwise fences and attached tabs on the hinge-moment characteristics of a half-delta tip control mounted on a 60 degree delta wing. Testing occurred over a range of angles of attack and control deflection. Results indicated that, in general, the effect of fences was to improve the linearity of hinge-moment curves and increase the negative values of slope parameters of hinge moment against control deflection and angle of attack.

Memorandum presenting testing conducted to determine the conductivity of magnesium oxide, stainless steel, and uranium oxide powders in various gases at a range of temperatures. Results regarding the experimental effective conductivities, comparison of analytical and experimental results, and effect of pressure on conductivity are provided.

The results of an investigation of the effects of leading-edge chord-extensions and extensible leading-edge flaps on the low-speed aileron characteristics of a 52 degrees sweptback wing with circular-arc airfoil sections are presented. A description and illustrations of the vortex flow as it passes over the wing are included. The investigation was conducted at Reynolds numbers of 5.5 times 10(exp 6) and 1.3 times 10(exp 6) and corresponding Mach numbers of 0.11 and 0.065 for an angle-of-attack range of 0 degrees through stall.

From Introduction: "As a part of the comprehensive investigation of the XJ34-WE-32 engine conducted in the NACA Lewis altitude wind tunnel, the over-all-performance was determined over a range of altitudes and flight Mach numbers. Other phases of the investigation are reported in reference 1. The results are given in tables and also in graphical form to show the trends of engine performance associated with changes of altitude, flight Mach number, and exhaust-nozzle area."

From Introduction: "The present investigation presents the lift and moment characteristics of an aspect-ratio-4.0 tail, sweptback 45^o at the quarter-chord line and pivoted about an axis sweptback 55.5^o and passing through the leading edge of the root-chord line."