Amended order of dismissal in PWA v Nelson.

This document evaluates the need for tritium sampling of the emissions from the 200 East Area Double Shell Tanks based on the requirements of {open_quotes}National Emission Standards for Hazardous Air Pollutants{close_quotes} (NESHAP). The NESHAP requirements are specified in 40 Code of Federal Regulation (CFR), Part 61, Subpart H; {open_quotes}National Emission Standards for Emissions of Radionuclides Other than Radon from Department of Energy Facilities{close_quotes}.

This report is a progress report to the US DOE from the Board on Radioactive Waste Management (BRWM), which summarizes the activities of the board during the period December 1, 1993 to May 2, 1994. The report summarizes the meetings of the board as a whole, of various of its subcommittees, and of activities it has undertaken to further its original mission. This board is associated with the National Research Council to give advice to US DOE.

This report summarizes and documents the results of the radiological surveys conducted over the surface of the 100-DR-1 Operable Unit, Hanford Site, Richland, Washington. In addition, this report explains the survey methodology using the Ultrasonic Ranging and Data System (USRADS). The 100-DR-1 radiological survey field task consisted of two activities: characterization of the operable unit-specific background conditions and the radiological survey of the operable unit surface area. The survey methodology was based on utilization of USRADS for automated recording of the gross gamma radiation levels at or near 6 in. and at 3 ft from the surface soil. The purpose of the survey is to identify the location of unidentified subsurface radioactive material areas and any surface contamination associated with these areas. The radiological surveys were conducted using both a digital count rate meter with a NaI detector reporting in counts per minute (CPM) and a dose rate meter reporting micro-Roentgen per hour (uR) connected to a CHEMRAD Tennessee Corp. Series 2000 USRADS. The count rate meter was set for gross counting, i.e., Window ``out``. The window setting allows detection of low, intermediate, and high energy photons. The USRADS equipment is used to record the detector readings verses the location …

This document is the Health and Safety Plan (HASP) for the demonstration of IITRI`s EM Treatment Technology. In this process, soil is heated in situ by means of electrical energy for the removal of hazardous organic contaminants. This process will be demonstrated on a small plot of contaminated soil located in the Pit Area of Classified Burial Ground K-1070-D, K-25 Site, Oak Ridge, TN. The purpose of the demonstration is to remove organic contaminants present in the soil by heating to a temperature range of 85{degrees} to 95{degrees}C. The soil will be heated in situ by applying 60-Hz AC power to an array of electrodes placed in boreholes drilled through the soil. In this section a brief description of the process is given along with a description of the site and a listing of the contaminants found in the area.

This DOE research project was established to document the integrated team approach for solving reservoir engineering problems. A field study integrating the disciplines of geology, geophysics, and petroleum engineering will be the mechanism for documenting the integrated approach. This is an area of keen interest to the oil and gas industry. The goal will be to provide tools and approaches that can be used to detect reservoir compartments, reach a better reserve estimate, and improve profits early in the life of a field.

The Materials Technology Section (MTS) of the Savannah River Technology Center (SRTC) was asked to demonstrate the practicality of recycling previously contaminated stainless steel components such as reactor heat exchanger heads, process water piping and slug buckets into 208 liters (55 gallon) drums and 2.8 cubic meter (100 ft{sup 3}) storage boxes. Radioactively contaminated stainless steel scrap will be sent to several industrial partners where it will be melted, decontaminated/cast into ingots, and rolled into plate and sheet and fabricated into the drums and boxes. As part of this recycle initiative, MTS was requested to demonstrate that radioactively contaminated Type 304L stainless steel could be remelted and cast to meet the applicable ASTM specification for fabrication of drums and boxes. In addition, MTS was requested to develop the technical basis of melt decontamination and establish practicality of using this approach for value added products. The findings presented in this investigation lead to the following conclusions: recycle of 18 wt% Cr-8 wt% Ni alloy can be achieved by melting Type 304 stainless steel in a air vacuum induction furnace; limited melt decontamination of the contaminated stainless steel was achieved, surface contamination was removed by standard decontamination techniques; carbon uptake in the …

This guide provides detailed compilations of international, federal, and state transportation related regulations applicable to shipments originating at or destined to Tennessee facilities. Information on preferred routes is also given.

This report documents progress on a project to demonstrate suitability of Thermally Modified Sand (TMS) for large scale use by demonstrating its performance on icy roadways maintained by the State of Alaska Department of Transportation. This report deals primarily with the startup of the project and includes initial observations of the effectiveness of the use of the TMS versus the typical salt/sand combination.

This bibliography is divided into the following four sections: Seismicity of Hawaii and Kilauea Volcano; Occurrence, locations and accelerations from large historical Hawaiian earthquakes; Seismic hazards of Hawaii; and Methods of seismic hazard analysis. It contains 62 references, most of which are accompanied by short abstracts.

Principal focus was on phase transformation, microstructure development, and elevated temperature creep, with some effort on room- temperature mechanical properties of selected materials. Fabrication was largely hot pressing, although many of the compositions can be densified by pressureless sintering; hot pressing was to ensure full attainment of density with fine microstructure. Most of the work was on SiC-AlN and AlN-Al{sub 2}OC pseudobinaries.

In support of start-up activities for the In Tank Precipitation (ITP) process, a thermowell is scheduled to be removed from Tank 48. Disposal of the thermowell in the Solid Waste Disposal Facility (SWDF) requires manifesting the quantities of several radioisotopes and, equally important, declaring that the waste package is nonhazardous. Sampling of the waste in the package (i.e., the thermowell) to determine quantities of hazardous materials or to perform a Toxicity Characteristic Leaching Procedure (TCLP) is not prudent or practical. Extremely high dose rates due to contamination of the thermowell preclude any close contact to obtain smear samples, and obtaining a representative sample of the various parts of the thermowell for a TCLP is not feasible. Alternatively, the TCLP can be simulated using a limited amount of data supplemented with process knowledge. This information can be further developed into a conservative screening tool to provide guidance on declaring whether the waste package is hazardous or not. This report documents the information and calculations of hazardous component concentrations used to support the possible disposal of the Tank 48 thermowell.

This document is written for the 242-A evaporator vacuum condenser system (VCS), describing its purpose and operation within the evaporator. The document establishes the operating parameters specifying pressure, temperature, flow rates, interlock safety features and interfacing sub-systems to support its operation.

In this report we present measurements of the diverter heat flux in DIII-D for ELMing H-mode and radiative diverter conditions. In previous work we have examined heat flux profiles in lower single-null diverted plasmas and measured the scaling of the peak heat flux with plasma current and beam power. One problem with those results was our lack of good power accounting. This situation has been improved to better than 80--90% accountability with the installation of new bolometer arrays, and the operation of the entire complement of 5 Infrared (IR) TV cameras using the DAPS (Digitizing Automated Processing System) video processing system for rapid inter-shot data analysis. We also have expanded the scope of our measurements to include a wider variety of plasma shapes (e.g., double-null diverters (DND), long and short single-null diverters (SND), and inside-limited plasmas), as well as more diverse discharge conditions. Double-null discharges are of particular interest because that shape has proven to yield the highest confinement (VH-mode) and beta of all DIII-D plasmas, so any future diverter modifications for DIII-D will have to support DND operation. In addition, the proposed TPX tokamak is being designed for double-null operation, and information on the magnitude and distribution of diverter …

Preliminary subsystem designs were developed for a Low-Emission Boiler System. Key features of the NO{sub x} and Boiler Subsystem includes: deep staged combustion with advanced low NO{sub x} burners in a furnace arrangement designed to minimize NO{sub x} emission, advanced pulverizer design, advanced operating diagnostics and control integration of steam conditions, combustion, burner management, and sootblowing.

This plan establishes a Department-wide goal to reduce total releases of toxic chemicals to the environment and off-site transfers of such toxic chemicals by 50 percent by December 31, 1999, in compliance with Executive Order 12856. Each site that meets the threshold quantities of toxic chemicals established in the Emergency Planning and Community Right-to-Know Act (EPCRA) will participate in this goal. In addition, each DOE site will establish site-specific goals to reduce generation of hazardous, radioactive, radioactive mixed, and sanitary wastes and pollutants, as applicable. Implementation of this plan will represent a major step toward the environmental risks and costs associated with DOE operations and increasing the Department`s use of preventive environmental management practices. Investing in Waste Minimization Pollution Prevention (WMin/PP) steadily reduce hazardous and radioactive waste generation and will reduce the need for waste management and unnecessary expenditures for waste treatment, storage, and disposal. A preventive approach to waste management will help solve current environmental and regulatory issues and reduce the need for costly future corrective actions. The purpose of this plan is to establish the strategic framework for integrating WMin/PP into all DOE internal activities. This program includes setting DOE policy and goals for reducing the generation of …

Two problems are addressed in this report: Potential flammability of gases, vapors, and an aerosol in tank 241-C-103 (hereafter identified as C-103) and potential worker health and safety hazards associated with the toxicity of constituents in C-103. Previous work indicated the potential presence of a fog in the tank, and the fuel content of the tank gases, vapors, and aerosol may be too high to permit work in the tank. Ten reports of adverse health effects associated with vapor exposures near C-103 or in C-Farm have been made by workers. Reported symptoms include headaches, burning sensations in nose and throat, nausea, and impaired pulmonary function. Data are needed to identify and quantify constituents of the C-103 headspace to address potential vapor toxicity. When the compounds of toxicological interest in the tank headspace are identified, industry hygienists can assess ``worst-case`` worker exposure levels and focus their industrial hygiene monitoring strategy on these target compounds. Final recommendations on the required level of personal protective equipment will be based on the worker breathing zone levels of these chemicals.

Despite the current worldwide oil glut, the United States will ultimately require large-scale production of liquid (transportation) fuels from coal. Slurry phase Fischer Tropsch (FT) technology, with its versatile product slate, may be expected to play a major role in production of transportation fuels via indirect coal liquefaction. Texas A&M University (TAMU) with sponsorship from the US Department of Energy, Center for Energy and Mineral Resources at TAMU, Texas Higher Education Coordinating Board, and Air Products and Chemicals, Inc., has been working on development of improved iron FT catalysts and characterization of hydrodynamic parameters in two- and three-phase bubble columns with FT derived waxes. Our previous studies have provided an improved understanding of the role of promoters (Cu and K), binders (silica) and pretreatment procedures on catalyst activity, selectivity and longevity (deactivation). The objective of the present contract was to develop improved catalysts with enhanced slurry phase activity and higher selectivity to liquid fuels and wax. This was accomplished through systematic studies of the effects of pretreatment procedures and variations in catalyst composition (promoters and binders). The major accomplishments and results in each of these two main areas of research are summarized here.

Electrostatic beneficiation of dry coal has received significant attention in the last decade. In this process the coal is ground and then charged, either by corona charging or by triboelectrification (friction charging). Coal and minerals receive different levels of charge -- often opposite polarities in the case of triboelectrification -- and can then be separated based on differences in electrical mobility. Problems associated with the techniques include rapid deposition of particles on the electrodes, thus, effecting further separation. The goal of this project is to optimize the electrostatic coal cleaning process to remove pyrites and inorganic materials through studies of the electrostatic properties of powdered coal, in-situ measurements of the electrodynamics of coal and mineral particles inside the separator, and development of self-cleaning collector plates for continuous separation.

The National Energy Information Center (NEIC), as part of its mission, provides energy information and referral assistance to Federal, State, and local governments, the academic community, business and industrial organizations, and the general public. The two principal functions related to this task are (1) operating a general access telephone line, and (2) responding to energy-related correspondence addressed to the Energy Information Administration (EIA). The Energy Information Directory was developed to assist the NEIC staff, as well as other Department of Energy (DOE) staff, in directing inquiries to the proper offices within DOE, other Federal agencies, or energy-related trade associations. The Directory is a list of most Government offices and trade associations that are involved in energy matters. It does not include those DOE offices which do not deal with the public or public information.

There are two instrumentation systems in the 2F Evaporator facilities (bldg. 242-16F) that are classified as the Critical Protection (CP). They are the Evaporator Pot Temperature instrumentations and Steam Condensate Gamma Monitor. The pot instrumentation consists of two interrelated circuits sharing the same temperature sensor and transducer. They are the high alarm and interlock circuit and the recorder circuit. The gamma monitor instrumentation consists of four interrelated circuits sharing the same scintillation detector. They are the gamma alarm and interlock circuit, failure alarm and interlock circuit, condensate cesium activity recorder circuit, and condensate americium activity recorder circuit. The resulting uncertainties for the instrument circuits are tabulated. (GHH)

Slurry Fed Melters (SFM) have been developed in the United States, Europe, and Japan for the conversion of high-level radioactive waste (HLW) to borosilicate glass for permanent disposal. The newest design, the stirred melter, combines the high production rates and high glass quality features of the Joule-heated melters with the low-cost, compact, simple maintenance features of the pot melters. However, further engineering design and demonstrations are needed to operate the stirred melter on a large scale. This document outlines the program which develops a full scale stirred melter for the DWPF (240 pph), and provides a basis which will allow further scale-up of the technology for use in the Hanford High Level Waste Disposal Program (HLWDP) for up to four times the reference capacity.

As a result of the Concentrate Transfer System (CTS) tank ventilation system contamination event, a task team was formed to evaluate instrument loops associated with waste reduction equipment. During the event a conductivity probe designed to provide an alarm and initiate an interlock failed to respond to the presence of liquid. An investigation revealed that the probe had become disconnected from the loop. The daily functional check of the conductivity probe circuit only tested the circuit continuity from the ventilation unit to the control room and did not actually test the probe. To test the continuity, a test switch was used to simulate the conducting probe. Because the functional check did not test each part of the loop, the test could be satisfactorily completed even though the probe itself was inoperable. The function of the task team was to develop a list of loops and interlocks prioritized by importance and likelihood of similar failure. The team evaluated the associated loop calibration and functional test procedures to verify that they are adequate to ensure loop performance on a periodic frequency. This report documents the evaluation findings and associated actions required prior to startup of the 2F and 2H evaporators.

The Energy Information Administration (EIA) uses models of the US economy developed by Data Resources, Inc. (DRI) for conducting policy analyses, preparing forecasts for the Annual Energy Outlook, the Short-Term Energy Outlook, and related analyses in conjunction with EIA`s National Energy Modeling System (NEMS) and its other energy market models. Both the DRI Model of the US Economy and the DRI Personal Computer Input-Output Model (PC-IO){sup 2} were developed and are maintained by DRI as proprietary models. This report provides documentation, as required by EIA standards for the use of proprietary models; describes the theoretical basis, structure and functions of both DRI models; and contains brief descriptions of the models and their equations. Appendix A describes how the two large-scale models documented here are used to support the macroeconomic and interindustry modeling associated with the National Energy Modeling System. Appendix B is an article by Stephen McNees of the Federal Reserve Bank of Boston on ``How Large are Economic Forecast Errors.`` This article assesses the forecast accuracy of a number of economic forecasting models (groups) and is attached as an independent assessment of the forecast accuracy of the DRI Model of the US Economy.