Memorandum presenting an investigation of a full-scale afterburner with high burner-inlet velocity conducted to determine burner performance with several variations in burner design. Variables receiving particular attention were flameholder design and burner length. Results regarding diffuser performance, performance of the reference two-V-gutter flameholder, designs to improve combustion for high-velocity conditions, and operational characteristics are provided.

Memorandum presenting force-oscillation tests made in the 8-foot transonic pressure tunnel to investigate some effects of an overhang-type aerodynamic balance and of a flow spoiler on the dynamic hinge-moment characteristics of a full-span flap-type rudder on a 5-percent-thick, swept vertical fin of low aspect ratio. Test results how that the aerodynamic damping moment on the plain rudder becomes unstable near a Mach number of 0.975 and remains unstable to the maximum speed of the tests.

Aerodynamic characteristics of rectangular platform, all-movable controls combined with slender body of revolution at Mach 3 to 6.25. The results showed that lift variations with angle of attack were somewhat nonlinear for both control-body combinations tested.

Memorandum presenting two right circular cylinders tested in axial free flight over a Mach number range of 0.4 to 1.7 by using the rocket-boosted-model technique. Results regarding time history, basic data cross plots, center of pressure, and drag are provided.

Memorandum presenting an investigation of hemispherical nose shapes of titanium, stainless steel coated with aluminum oxide, and uncoated stainless steel with lithium hydride and magnesium as internal coolants. Results regarding titanium models, stainless-steel models (uncoated), stainless-steel models coated with aluminum oxide, solution effects on the decomposition temperature of lithium hydride, effect of lithium hydride and magnesium on temperature measurements, and efficiency of models cooled with lithium hydride are provided.

"A study has been made of a flare-cylinder configuration to investigate its feasibility as a reentry body of an intermediate range ballistic missile. Factors considered were heating, weight, stability, and impact velocity. A series of trajectories covering the possible range of weight-drag ratios were computed for simple truncated nose shapes of varying pointedness, and hence varying weight-drag ratios" (p. 1).

Report discussing testing on a scale model of the Convair XF2Y-1 airplane with solid-fuel rocket motors that simulate full-scale turbojet-engine characteristics at a height of 35,000 feet with full afterburning at Mach number 1.53. The model was found to have dynamic lateral instability, but these results were not likely to be found in a full-scale airplane. Information about the pitching moment, directional stability, lift-curve slope, and drag coefficients is provided.

Report presenting a full-scale, free-jet investigation to determine the performance of a side-inlet supersonic diffuser designed for a flight Mach number of 2.75. Several internal modifications made to improve diffuser-outlet flow uniformity were also evaluated. Results regarding the general characteristics of the diffuser and effect of diffuser modifications on flow distribution are provided.

Report presenting tests of the extent of laminar flow that can be obtained with practical wing-surface conditions. Chemical sublimation was used for boundary-layer-flow visualization on the wings of a supersonic fighter airplane in level flight. A method of continuous monitoring using heat temperature resistance gauges was also used on one wing.

Memorandum presenting an analysis of a large number of liquid-metal-to-air heat-exchanger cores for the nuclear-powered liquid-metal turbojet cycle to determine which types yield the best overall net thrust per total engine weight. The performances of all exchangers considered were initially evaluated at a median condition. The performance of the best of each of the four types was compared with that of a shell-and-tube exchanger with the air flowing through the tubes, operating at the same condition.

Report presenting the performance of a side inlet with a fixed 12 degree two-dimensional compression surface for a range of Mach numbers, angles of attack, and yaw. The effects of several methods of compression-surface boundary-layer removal were investigated as well as a solid ramp.

Free flight test of tailless missile configuration with 45-deg sweptback wing of aspect ratio 4 - stability at transonic speeds. The longitudinal flexible-wing results indicated a gradual transonic trim change a lift-curve slope comparable with that for the same configuration with a wing of aspect ratio 5.5. Results regarding trim characteristics, lift and longitudinal stability, and side-force and lateral stability are provided.

Report presenting testing of two full-scale models of an inline, cruciform, canard missile configuration with a low-aspect-ratio wing equipped with flap-type controls to determine the missile's longitudinal aerodynamic characteristics. Stability derivatives and control and drag characteristics are provided.

Memorandum presenting a free-flight investigation to determine the lift, drag, static stability, and hinge-moment characteristics of a rocket-powered model of a rocket-powered model of a ballistic-missile configuration at supersonic speeds. The model consisted essentially of a body of fineness ratio 16.9 and a cruciform set of small 60 degree delta fins located approximately 1 body diameter from the base of the body. The model lift and pitching-moment coefficients were nonlinear with angle of attack.

Results regarding testing of steel projectiles fired into copper targets at velocities from 5,000 to 11,500 feet per second, which indicated that as target temperature is increased, the crater size also increases. Twenty-two caliber steel cylinders and steel spheres were used as projectiles.

Chemical sublimation has been employed for boundary-layer-flow visualization on the wings of a supersonic fighter airplane in level flight at speeds near a Mach number of 2.0. The tests have shown that laminar flow can be obtained over extensive areas of the wing with practical wing-surface conditions. In addition to the flow visualization tests, a method of continuously monitoring the conditions of the boundary layer has been applied to flight testing, using heated temperature resistance gages installed in a Fiberglas "glove" installation on one wing. Tests were conducted at speeds from a Mach number of 1.2 to a Mach number of 2.0, at altitudes from 35,000 feet to 56,000 feet. Data obtained at all angles of attack, from near 0 deg to near 10 deg, have shown that the maximum transition Reynolds number on the upper surface of the wing varies from about 2.5 x 10(exp 6) at a Mach number of 1.2 to about 4 x 10(exp 6) at a Mach number of 2.0. On the lower surface, the maximum transition Reynolds number varies from about 2 x 10(exp 6) at a Mach number of 1.2 to about 8 x 10(exp 6) at a Mach number of 2.0.

"The steady pressure loads as well as the temperature change on adjacent surfaces due to the presence of a propulsive jet at subsonic speeds is shown to be insignificant. Whereas at supersonic speeds the temperature effect might be expected to remain insignificant, the steady pressure loads were shown to increase greatly on surfaces downstream of the propulsive jet exit" (p. 1).

Attenuation of tangent-pressure oscillation in liquid-oxygen-heptane rocket engine combustion chamber using longitudinal fin. Results regarding the engine performance with injector A, effect of fins with injector A, and destructiveness of screaming are provided.

Report presenting the performance characteristics of a 20-inch ramjet opeerating with preheated unleaded 62 octane fuel. The results of the investigation indicated an improvement in the combustion efficiency and operating range of the ramjet when using preheated fuel.

Report presenting an investigation in the two-dimensional low-turbulence tunnels to develop optimum double-slotted-flap configurations for seven thin NACA airfoil sections. Each was equipped with the same flaps and measured at the same Reynolds numbers. Results regarding the lift characteristics and pitching moment are provided.

An investigation has been conducted in the Cleveland 18- by 18-inch supersonic tunnel at a Mach number of 1.85 and angles of attack from 0 deg to 5 deg to determine optimum design configurations for a convergent-divergent type of supersonic diffuser with a subsonic diffuser of 5 deg included divergence angle. Total pressure recoveries in excess of theoretical recovery across a normal shock at a free-stream Mach number of 1.85 wore obtained with several configurations.

Report presenting an investigation using the NACA wing-flow method to determine the longitudinal stability and control characteristics of a semispan airplane model with a wing of conventional plan form and a horizontal tail swept back 45 degrees at transonic speeds. Measurements were made of lift and angle of attack for trim at several stabilizer and elevator settings.

"A formula, based on a semirational analysis, is presented for estimating the torsional stiffness necessary to prevent flutter of a sweptback or unswept uniform wing that attains supersonic speeds. Results of missile flights at speeds up to Mach number 1.4 demonstrate the usefulness of the formula" (p. 1).

Report presenting a theoretical analysis of thrust augment of turbojet engines by tail-pipe burning and charts from which the thrust augmentation produced may be evaluated from the normal engine data and performance of the tail-pipe burner. Results regarding general curves and illustrative curves are provided.