Quarterly report on the metabolic properties of various materials, biological studies of radiation effects, health chemistry, health physics.

To calibrate a pulse height discriminator, the amplitude of the calibrating pulse must be known. If the amplitude is known, the discriminator dial may be calibrated in terms of the input signal required to just trip it. This is the purpose for which the Discriminator Calibrator was designed. It produces pulses of variable but known amplitude with a rep. rate variable from 3 pps to 4000 pps. The main use of this unit at the UCRL is in conjunction with scalers at fixed counting locations.

The use of diffusion theory to attempt to reproduce the chemical data of Hicks and Stevenson for the spatial distribution of neutrons in a solid block of uranium that is bombarded by 190 Mev neutrons is described.

Early in the design of the Mark I accelerator it was decided to install magnetic lenses in the drift tubes. A number of model magnets were constructed and tested to determine the best design for these lenses. This report includes only the results of the tests on the final models of the magnets that are designed for Mark I.

The recent interest in tributyl phosphate as an extracting solvent for uranium indicated that consideration of n-butyl phosphoric acid for this application might be of interest if some way could be devised to overcome the manipulation and miscibility difficulties. It was found that if the material was placed in any one of a number of carrier solvents, it had a remarkably strong extractive effect on uranyl ion out of acid solutions without a salting agent present.

The angle errors of a rotary table can be accurately measured by stepping off the angles with an optical caliper and computing table error from (1) the error readings at each angle measured and (2) the cumulative caliper error that will be evident when the circle is closed at 360', eliminating the necessity of adjusting the caliper to the exact setting.

The basic investigation of transistor feedback amplifiers has proven mathematically simple and of great practical value. The behavior of single-stage common-emitter amplifiers is described and provides a building block with which cascaded feedback amplifiers can be analyzed and designed. From the results of this analysis the conditions for minimum drift for cascaded single-stages and cascaded loops have been derived.

Presented herein is a philosophy for designing wideband multistage transistor amplifiers. The amplifier is visualized as an integral unit, the interstage networks constituting the elements of the amplifier unit. By designing the amplifier as a unit and adjusting the overall response (gain and bandwidth) with the interstage time constants, an increase in gain-bandwidth product is realized over the iteratively designed amplifiers. The resulting increase in gain-bandwidth product results from absence of the bandwidth shrinkage factor for multistage amplifiers. Formulas are derived for both a two- and three-transistor integrally designed wideband amplifier, in which shunt peaking networks are used for coupling. Experimental amplifiers were constructed following these formulas, and the observed performance agreed quite well with the calculations.

Technical report includes three reports of research progress: 1)Neutron scattering by A. Bratenahl; 2) Nuclear Cross Sections, Norman Knable.

Surface contamination with beryllium becomes a hazard to health only when the potential exists for resuspension in air in enough quantity and for enough time to exceed the prescribed standards for airborne exposures. There are several factors governing the rate and nature of resuspension phenomena. These factors include: the quantity and properties of the particular beryllium compound causing the contamination, the nature of the surface, activities in the vicinity, ventilation in the area which might affect the dilution of resuspended particles, and the presence of other control measures such as respiratory protection and use of wet methods. Generally, it has been found that the problem is minimal and can be easily controlled by exercising good judgement based upon consideration of pertinent factors governing resuspension, and a knowledge of the nature of beryllium toxicity.

The Chapman-Jouguet pressure and equation of state of the high explosives PBX 9404 and LX04-01 have been experimentally derived. To assure a strictly one-dimensional geometry, spheres of high explosives were used. Experimental measurements of the radius-time history of material accelerated by the explosive gases were used in conjunction with finite difference calculations of the hydrodynamic equations to obtain some previous inaccessible data on high explosives.

Progress reports on Accelerator Development Program, High Frequency Program, beam dynamics in strong focusing linear accelerators, spiral beam buncher experiments, dynamical properties of Mark I, mechanical design, and Target Physics Program.

A graph plotting pulse height analyzer of compact size and moderate cost is described. The operation is simple and flexible, and the instrument is easy to maintain.