We investigated electron and gamma spectra of mixtures of isotopes of curium. This was done on a beta spectrometer with double focusing at an angle of {pi}{radical}2 and on a scintillation gamma spectrometer with a 40 {times} 40 mm NAI(Tl) single crystal detector. The observed electron spectrum are interpolated and presented. Also, experimental results of the ratio of conversion at L and M subshells are presented and compared to theoretical values.

The authors have delivered several 64-element linear arrays of pyroelectric elements fully integrated on silicon wafers with MOS readout devices. They have delivered detailed drawings of the linear arrays to LANL. They have processed a series of two inch wafers per submitted design. Each two inch wafer contains two 64 element arrays. After spin-coating copolymer onto the arrays, vacuum depositing the top electrodes, and polarizing the copolymer films so as to make them pyroelectrically active, each wafer was split in half. The authors developed a thicker oxide coating separating the extended gate electrode (beneath the polymer detector) from the silicon. This should reduce its parasitic capacitance and hence improve the S/N. They provided LANL three processed 64 element sensor arrays. Each array was affixed to a connector panel and selected solder pads of the common ground, the common source voltage supply connections, the 64 individual drain connections, and the 64 drain connections (for direct pyroelectric sensing response rather than the MOSFET action) were wire bonded to the connector panel solder pads. This entails (64 + 64 + 1 + 1) = 130 possible bond connections per 64 element array. This report now details the processing steps and the progress of …

Neutron yields for alpha particle reactions with beryllium, boron, carbon, magnesium, and oxygen are calculated. The dependence on energy of the incoming alpha particles is analyzed for yield. Calculations are varied for different sets of cross section data.

The objective of this project is to develop environmentally-sound and cost-effective remediation techniques for crude oil contaminated soils. By providing a guidance manual to oil and gas operators, the Ohio Division of Oil and Gas regulatory authority hopes to reduce remediation costs while improving voluntary compliance with soil clean-up requirements. This shall be accomplished by conducting a series of field tests to define the optimum range for nutrient, oxygen and organic enhancement to biologically remediate soils contaminated with brines and crude oil having a wide range of viscosity. Task one of the bioremediation project began on July 3, 1995 with the selection and preparation of a site in Smith township. Mahoning County. The plots were arranged and parameters were varied. Plots, 1, 3, 5, 7, 9 and 11 were contaminated with 159 liters (42 gal. ) of Corning grade crude oil and plots 2, 4, 6, 8 and 12 were contaminated with 159 liters (42 gal.) of Pennsylvania grade crude oil. Plots 13 through 21 were contaminated with 159 liters (42 gal.) of Pennsylvania grade crude oil and 477 liters (126 gal.) of Clinton sandstone brine with a 160,000 mg/liter concentration of chloride. Treatment and administration of variables were conducted …

LLNL has an ongoing program of weapons disablement using energetic charged particle beams; this program combines theoretical and experimental expertise in accelerators, high-energy and nuclear physics, plasma physics and hydrodynamics to simulate/measure effects of electron and proton beams on weapons. This paper reviews work by LLNL, LANL and NSWC on detonating sensitive and insensitive high explosives and land mines using high-current electron beams. Computer simulations are given. 20--160 MeV electron beams incident on wet/dry soils are being studied, along with electron beam propagation in air. Compact high current, high energy accelerators are being developed for mine clearing. Countermine missions of interest are discussed. 25 refs., 9 figs.

Since the first demonstration of the laser in the 1960`s, lasers have found numerous applications in analytical chemistry. In this work, two different applications are described, namely, DNA sequencing with capillary gel electrophoresis and single cell analysis with mass spectrometry. Two projects are described in which high-speed DNA separations with capillary gel electrophoresis were demonstrated. In the third project, flow cytometry and mass spectrometry were coupled via a laser vaporization/ionization interface and individual mammalian cells were analyzed. First, DNA Sanger fragments were separated by capillary gel electrophoresis. A separation speed of 20 basepairs per minute was demonstrated with a mixed poly(ethylene oxide) (PEO) sieving solution. In addition, a new capillary wall treatment protocol was developed in which bare (or uncoated) capillaries can be used in DNA sequencing. Second, a temperature programming scheme was used to separate DNA Sanger fragments. Third, flow cytometry and mass spectrometry were coupled with a laser vaporization/ionization interface.

The research in this thesis explores the separation capabilities of a new technique termed electrochemically-modulated liquid chromatography (EMLC). The thesis begins with a general introduction section which provides a literature review of this technique as well as a brief background discussion of the two research projects in each of the next two chapters. The two papers which follow investigate the application of EMLC to the separation of a mixture of aromatic amino acids and of a mixture of polycyclic aromatic hydrocarbons (PAHs). The last section presents general conclusions and summarizes the thesis. References are compiled in the reference section of each chapter. The two papers have been removed for separate processing.

The revised Federal Facility Agreement and Consent Order states that a tank characterization plan will be developed for each double-shell tank and single-shell tank using the data quality objective process. The plans are intended to allow users and regulators to ensure their needs will be met and resources are devoted to gaining only necessary information. This document satisfies that requirement for Tank 241-U-203 sampling activities.

A capillary array electrophoresis system was chosen to perform DNA sequencing because of several advantages such as rapid heat dissipation, multiplexing capabilities, gel matrix filling simplicity, and the mature nature of the associated manufacturing technologies. There are two major concerns for the multiple capillary systems. One concern is inter-capillary cross-talk, and the other concern is excitation and detection efficiency. Cross-talk is eliminated through proper optical coupling, good focusing and immersing capillary array into index matching fluid. A side-entry excitation scheme with orthogonal detection was established for large capillary array. Two 100 capillary array formats were used for DNA sequencing. One format is cylindrical capillary with 150 {micro}m o.d., 75 {micro}m i.d and the other format is square capillary with 300 {micro}m out edge and 75 {micro}m inner edge. This project is focused on the development of excitation and detection of DNA as well as performing DNA sequencing. The DNA injection schemes are discussed for the cases of single and bundled capillaries. An individual sampling device was designed. The base-calling was performed for a capillary from the capillary array with the accuracy of 98%.

The mixed potential integral equation (MPIE) formulation is convenient for problems involving layered media because potential quantities involve low order singularities, in comparison to field quantities. For nonperiodic problems, the associated Green`s potentials involve spectral integrals of the Sommerfeld type, in the periodic case, discrete sums over sampled values of the same spectra are required. When source and observation points are in the same or in adjacent layers, the convergence of both representations is enhanced by isolating the direct and quasi-static image contributions associated with the nearby layers. In the periodic case, the convergence of direct and image contributions may be rapidly accelerated by means of the Ewadd method.

We are investigating a novel insulator concept which involves the use of alternating layers of conductors and insulators with periods less than 1 mm. These structures perform many times better (about 1.5 to 4 times higher breakdown electric field) than conventional insulators in long pulse, short pulse, and alternating polarity applications. We present our ongoing studies investigating the degradation of the breakdown electric field resulting from surface roughness, the effect of gas pressure, and the performance of the insulator structure under bi-polar stress. Further, we present our initial modeling studies.

Previous research into the alkali-metal-gallium systems has revealed a large variety of networked gallium deltahedra. The clusters are analogues to borane clusters and follow the same electronic requirements of 2n+2 skeletal electrons for closo-deltahedra. This work has focused on compounds that do not follow the typical electron counting rules. The first isolated gallium cluster was found in Cs{sub 8}Ga{sub 11}. The geometry of the Ga{sub 11}{sup 7{minus}} unit is not deltahedral but can be described as a penta-capped trigonal prism. The reduction of the charge from a closo-Ga{sub 11}{sup 13{minus}} to Ga{sub 11}{sup 7{minus}} is believed to be the driving force of the distortion. The compound is paramagnetic because of an extra electron but incorporation of a halide atom into the structure captures the unpaired electron and forms a diamagnetic compound. A second isolated cluster has been found in Na{sub 10}Ga{sub 10}Ni where the tetra-capped trigonal prismatic gallium is centered by nickel. Stabilization of the cluster occurs through Ni-Ga bonding. A simple two-dimensional network occurs in the binary K{sub 2}Ga{sub 3} Octahedra are connected through four waist atoms to form a layered structure with the potassium atoms sitting between the layers. Na{sub 30.5}Ga{sub 60{minus}x}Ag{sub x} is nonstoichiometric and needs only …

Solid and liquid radioactive waste continues to be stored in 149 single-shell tanks at the Hanford Site. To date, 119 tanks have had most of the pumpable liquid removed by interim stabilization. Thirty tanks remain to be stabilized. One of these tanks (C-106) will be stabilized by retrieval of the tank contents. The remaining 29 tanks will be interim stabilized by saltwell pumping. In the summer of 1997, the US Department of Energy (DOE) placed a moratorium on the startup of additional saltwell pumping systems because of funding constraints and proposed modifications to the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement) milestones to the Washington State Department of Ecology (Ecology). In a letter dated February 10, 1998, Final Determination Pursuant to Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement) in the Matter of the Disapproval of the DOE`s Change Control Form M-41-97-01 (Fitzsimmons 1998), Ecology disapproved the DOE Change Control Form M-41-97-01. In response, Fluor Daniel Hanford, Inc. (FDH) directed Lockheed Martin Hanford Corporation (LNMC) to initiate development of a project plan in a letter dated February 25, 1998, Direction for Development of an Aggressive Single-Shell Tank (SST) Interim Stabilization Completion Project Plan in Support of Hanford …

The 105 KE Basin Recirculation System and Skimmer Loop have been upgraded to provide the flexibility to run the Ion Exchange Modules on either system to support spent fuel removal for the Spent Nuclear Fuel Project. This Acceptance Test Report Provides the documentation of the leak Testing for the construction work associated with the IXM inlet and outlet piping, places the cartridge filters back in service and provides the functional testing of the IXM`s on the recirculation and skimmer systems.

The overall objective of this project is to develop sensor-integrated ``intelligent`` diamond wheels for grinding of ceramics. Such wheels will be ``smart`` enough to monitor and supervise both the wheel preparation and grinding processes without the need to instrument the machine tool. Intelligent wheels will utilize reusable cores integrated with two types of sensors: acoustic emission (AE) and dynamic force transducers. Signals from the sensors will be transmitted from a rotating wheel to a receiver by telemetry. Wheels will be ``trained`` to recognize distinct characteristics associated with truing, dressing and grinding.

This report describes a new evaluation conducted to help understand the thermal-hydraulic behavior of tank A-101. Prior analysis of temperature data indicated that the dome space and upper waste layer was slowly increasing in temperature increases are due to increasing ambient temperatures and termination of forced ventilation. However, this analysis also indicates that other dome cooling processes are slowly decreasing, or some slow increase in heating is occurring at the waste surface. Dome temperatures are not decreasing at the rate expected as a forced ventilation termination effects are accounted for.

The Department of Energy Isotope Production and Distribution Program mission is to serve the national need for a reliable supply of isotope products and services for medicine, industry and research. The program produces and sells hundreds of stable and radioactive isotopes that are widely utilized by domestic and international customers. Isotopes are produced only where there is no U.S. private sector capability or other production capacity is insufficient to meet U.S. needs. The Department encourages private sector investment in new isotope production ventures and will sell or lease its existing facilities and inventories for commercial purposes. The Isotope Program reports to the Director of the Office of Nuclear Energy, Science and Technology. The Isotope Program operates under a revolving fund established by the Fiscal Year (FY) 1990 Energy and Water Appropriations Act and maintains financial viability by earning revenues from the sale of isotopes and services and through annual appropriations. The FY 1995 Energy and Water Appropriations Act modified predecessor acts to allow prices charged for Isotope Program products and services to be based on production costs, market value, the needs of the research community, and other factors. Although the Isotope Program functions as a business, prices set for small-volume, …

The gene identification problem is the problem of interpreting nucleotide sequences by computer, in order to provide tentative annotation on the location, structure, and functional class of protein-coding genes. This problem is of self-evident importance, and is far from being fully solved, particularly for higher eukaryotes, Thus it is not surprising that the number of algorithm and software developers working in this area is rapidly increasing. The present paper is an overview of the field, with an emphasis on eukaryotes, for such developers.

Part I (Inventory of Existing Data and Information Sources) objectives are to provide improved access to information available in the public domain by inventorying data files and records of the major information repositories in the Eastern Gulf Coastal Plain and making these inventories easily accessible in electronic format. The producers in the region maintain that the accessibility of oil and gas information is the single-most important factor to assist them in finding new hydrocarbon discoveries and in improving production from established fields. The principal investigator continues to discuss the project with geologists for Alabama, Mississippi, and Florida. A subcontract has been executed between the University of Alabama and the Geological Survey of Alabama. A subcontract agreement is under review by the Mississippi Office of Geology. The principal investigator continues to discuss the project with a number of faculty members from departments of geology in the region. A listing of theses and dissertations from the University of Alabama, Auburn University, Mississippi State University, University of Mississippi, University of Southern Mississippi, University of Southwestern Louisiana, and Louisiana State University related to the petroleum geology of the Mississippi Interior Salt Basin has been compiled. This list is accessible electronically through the Home Page …

In this Paper we provide a direct comparison of several important algorithms designed to track fluid interfaces. In the process we propose improved criteria by which these methods are to be judged. We compare and contrast the behavior of the following interface tracking methods: high order monotone capturing schemes, level set methods, volume-of-fluid (VOF) methods, and particle-based (particle-in-cell, or PIC) methods. We compare these methods by first applying a set of standard test problems, then by applying a new set of enhanced problems designed to expose the limitations and weaknesses of each method. We find that the properties of these methods are not adequately assessed until they axe tested with flows having spatial and temporal vorticity gradients. Our results indicate that the particle-based methods are easily the most accurate of those tested. Their practical use, however, is often hampered by their memory and CPU requirements. Particle-based methods employing particles only along interfaces also have difficulty dealing with gross topology changes. Full PIC methods, on the other hand, do not in general have topology restrictions. Following the particle-based methods are VOF volume tracking methods, which are reasonably accurate, physically based, robust, low in cost, and relatively easy to implement. Recent enhancements …

This document describes the basis for the development of the System for Highly Radioactive Equipment Dismantlement or SHRED. It is the result of a thorough investigation into current and past dismantlement practices at shielded cell facilities around the DOE complex. This information has been used to formulate the development requirements for the SHRED.

This paper presents the results of a study to evaluate the effects of soil-structure interaction (SSI) on the ambient vibration response of the switchyard/target area (S/TA) buildings at the National Ignition Facility (NIF) presently under construction at the Lawrence Livermore National Laboratory (LLNL) in Livermore, California. This laser facility houses optical and other special equipment whose alignment stability is sensitive to vibrations caused by ambient vibrations or other vibrating sources. In evaluating the deformations and displacements of the S/TA structures, the contribution of the SSI to the overall system flexibility can be very significant. The present study examines the results of fixed-base and SSI analyses of these massive stiff structures to develop an understanding of the potential contribution of SSI to the overall system displacements and deformations. A simple procedure using a set of factors is recommended for scaling the results of fixed-base analyses to approximately account for SSI effects.

As described in contribution AF99-0335, it is interesting that new security services and mechanisms are allowed to be negotiated during a connection in progress. To do that, new ''negotiation OAM cells'' dedicated to security should be defined, as well as some acknowledgment cells allowing negotiation OAM cells to be exchanged reliably. Remarks which were given at the New Orleans meeting regarding those cell formats are taken into account. This contribution presents some baseline text describing the format of the negotiation and acknowledgment cells, and the using of those cells. All the modifications brought to the specifications are reversible using the Word tools.

A significant amount of effort has been devoted to determining the properties and understanding the behavior of the alloy MA957 to define its potential usefulness as a cladding material, in the fast breeder reactor program. The numerous characterization and fabrication studies that were conducted are documented in this report. The alloy is a ferritic stainless steel developed by International Nickel Company specifically for structural reactor applications. It is strengthened by a very fine, uniformly distributed yttria dispersoid. Its fabrication involves a mechanical alloying process and subsequent extrusion, which ultimately results in a highly elongated grain structure. While the presence of the dispersoid produces a material with excellent strength, the body centered cubic structure inherent to the material coupled with the high aspect ratio that results from processing operations produces some difficulties with ductility. The alloy is very sensitive to variations in a number of processing parameters, and if the high strength is once lost during fabrication, it cannot be recovered. The microstructural evolution of the alloy under irradiation falls into two regimes. Below about 550 C, dislocation development, {alpha}{prime} precipitation and void evolution in the matrix are observed, while above about 550 C damage appears to be restricted to cavity …