Report discussing an investigation of external-store characteristics using a 245-gallon external fuel tank mounted under a wing of a North American F-86A airplane. The store normal force was found to increase abruptly on penetration of the buffet boundary. Information about the normal- and side-load distribution and integrated force and moment coefficients is provided.

"Measurement of average skin-friction coefficients have been made on six rocket-powered free-flight models by using the boundary-layer rake technique. The model configuration was the NACA RM-10, a 12.2-fineness-ratio parabolic body of revolution with a flat base. Measurements were made over a Mach number range from 1 to 3.7, a Reynolds number range 40 x 10(exp 6) to 170 x 10(exp 6) based on length to the measurement station, and with aerodynamic heating conditions varying from strong skin heating to strong skin cooling" (p. 1).

Report presenting tests to determine the flight characteristics of an F-86 airplane equipped with a blowing-type boundary-layer-control installation on the trailing-edge flaps. The effectiveness of the flap was determined in conjunction with slatted leading edges and an inflatable rubber boot on the leading edge. Measurements were made of lift, drag, flow requirements, and computations for take-off, climb, and landing.

Report presenting a flight investigation at a range of altitudes to determine the wing loads on the Convair XF-92A airplane over the lift range of the airplane at subsonic and transonic speeds. Theoretical lift-curve slope for a delta wing was calculated and compared with the flight data at a Mach number of 0.75.

Report presenting a pilot-opinion survey conducted with a conventional fighter airplane fitted with special servo devices for varying in flight the dihedral effect, static directional stability, and directional damping. Results showing the boundaries that define satisfactory and tolerable lateral oscillatory characteristics are presented.

Report presenting a flight investigation of a rocket-launched ram-jet engine incorporating an end-burning solid fuel. Results regarding acceleration, altitude, booster separation, survival time of booster adapter, and air specific impulse are provided.

Report presenting the results of force and moment tests at Mach numbers from 3.0 to 6.3 on bodies of revolution of fineness ratios from 5 to 10 and on flat-bottom bodies of fineness ratio 10 along with theoretical predictions for these bodies. Testing included eight cone and cone-cylinder models, six nose-cylinder models, and three flat-bottom bodies.

Report presenting an investigation to determine the zero-lift rolling effectiveness of all-movable sweptback horizontal tail fins mounted behind a notched delta wing at a constant angle of differential incidence of 7 degree per fin. Two models, one with a stiff wing and one with a flexible wing, were tested in free flight over a range of Mach numbers. The rolling effectiveness was about the same magnitude at subsonic and supersonic speeds for both models.

Report presenting a rocket-propelled missile model with cruciform, triangular, inline wings and tails, which has been tested through a range of Mach numbers at small wing-deflection angles. Results regarding the stability and damping, control effectiveness, and hinge moments are provided.

Memorandum presenting a model of a 60 degree delta-wing bomber with strut-mounted Siamese nacelles, which was designed, with the use of a symmetrical fuselage indentation, to have a smooth average area distribution at a Mach number of 1.20. The results show that the configuration drag rise was significantly higher than that from the equivalent-body tests and area-rule theory throughout the Mach number range. Results regarding total drag and pressure drag are provided.

From Summary: "An investigation of the altitude performance of a 20-inch-diameter high-temperature-ratio ram-jet combustor which had been redesigned to provide good combustor efficiency over a wide range of temperature ratios was conducted at zero angle of attack in a free-jet facility at a Mach number of 3.0. Configurations investigated incorporated a cylindrical control sleeve which confined the injected fuel at low over-all fuel-air ratios to about 40 percent of the engine air flow. This provided an optimum fuel-air mixture over a portion of the flame holder when the over-all fuel-air ratio was about 0.02."

Report presenting an exploratory investigation of the effectiveness of outboard horizontal tails in reducing the static longitudinal stability changes with lift coefficient associated with many sweptback wings. The results indicated that outboard horizontal tails can be a very effective means of counteracting the trend toward longitudinal instability characteristics of many sweptback wings. Results regarding the effects of changes in horizontal-tail position, effects of wing fences, average downwash at the tail, effects of changing tail size, lift, drag, and pitching-moment characteristics, and effects of flaps are provided.

Memorandum presenting an icing investigation conducted to determine the general de-icing and runback characteristics of three production samples of electric rubber-clad cyclic de-icing boots. The overall de-icing characteristics of two of the boots investigated were quite similar. Results regarding boot surface temperatures and general de-icing and runback characteristics are provided.

Report presenting an icing investigation conducted in the icing research tunnel to determine the general de-icing and runback characteristics of three production samples of electric rubber-clad cyclic de-icing boots. The boots were all designed for the same airplane and were designed to operate at the same values of power density, heat-on time, and cycle ratio. Results regarding the boot surface temperatures and general de-icing and runback characteristics are provided.

"Small-perturbation spectral-analysis techniques are used to obtain the root-mean-square flame-generated turbulence velocities and the attenuating pressure fluctuations stemming from interaction of a constant-pressure flame front with a field of isotropic turbulence in the absence of turbulence decay processes. The anisotropic flame-generated turbulence velocities are found to be of about the same intensity as those of the incident isotropic turbulence, the lateral turbulence velocities being always lower, but the longitudinal velocity is somewhat increased for flame-temperature ratios over 7" (p. 599).

Report presenting measurements of the normal force and pitching moment of a rectangular tail surface at Mach 1.9 to determine the interference effects due to trailing shock waves from an axisymmetric body with a jet exiting from a sonic nozzle in the base. The data were obtained at various jet pressure ratios and locations of tail with respect to the body. Results regarding tail location, tail pitching moment, and tail-shock-wave effects on base pressure are provided.

Report presenting an investigation of the pressure distribution over a rectangular wing with a 9-percent-thick symmetrical circular-arc section and a 30-percent-chord trailing-edge flap. Results are given for pressure distributions, Schileren and liquid-film studies, and wing section characteristics are provided.

Memorandum presenting an investigation to evaluate the effect of Reynolds number and Mach number on the aerodynamic characteristics of a horizontal tail of aspect ratio 3 equipped with a plain, sealed, full-span elevator. The line joining the quarter-chord points of the airfoil sections was swept back 45 degrees and the sections perpendicular to this line were the NACA 64A010. Results regarding the effect of Reynolds number and effects of leading-edge roughness and elevator-nose seal are provided.

Report presenting an investigation to study the aerodynamic problems associated with a turbine design for a mode of engine operation which utilizes turbine stator adjustment to maintain a fixed compressor operating point. An indication of the turbine requirements for a particular compressor operating point indicated that a feasible sing-stage air-cooled turbine design could be obtained within reasonable aerodynamic limits. Results regarding the performance of the turbine, pressure ratios, and operational requirements are provided.

Report presenting visual observations and flow analyses made of annular liquid flow with cocurrent air flow in 2- and 4-inch-diameter horizontal transparent tubes. The experiments occurred over a range of air mass velocities, air temperatures, and Reynolds numbers. Results regarding the velocity and thickness of liquid films, description of water-film disturbances, effect of flow variables on liquid-film characteristics, and relation between disturbances and flow conditions are provided.

Report presenting an investigation of spoilers at a Mach number of 1.93 to determine the effects of height and chordwise location on the section pressure distributions and section aerodynamic characteristics of a two-dimensional, 6-percent-thick, symmetrical wing. Spoilers of 3-, 5-, and 7-percent-chord height were tested at three chordwise locations. Results regarding pressure distributions, aerodynamic characteristics, and shock boundary-layer interactions are provided.

Memorandum presenting an investigation of a series of five 75S-T6 aluminum-alloy elementary skin and spar-cap combinations with skin varying from 0.051 to 0.500 inch in thickness to determine the temperature and stress gradients resulting from the application of heat to the surface. The data are presented in the form of tables of the measured temperatures and stresses calculated from the measured strains.

Report presenting an investigation in the 4- by 4-foot supersonic pressure tunnel to determine the effects of body indentation on the minimum drag and maximum lift-drag ratio of a 60 degree swept-wing-body combination. A secondary goal of the tests was to determine the effect on the maximum lift-drag ratio of modifying the inboard plan form of the 60 degree swept wing. Lift, drag, and pitching-moment data are presented.

Report presenting an investigation of the low-speed power-on stability and control characteristics of a free-flying model of the North American X-15 airplane. Results regarding the longitudinal stability and control, lateral stability, and lateral control are provided. Longitudinal stability was low, but it was considered to be satisfactory up to an angle of attack of about 30 degrees.