"Results have been obtained by means of a free-flight technique utilizing rocket propulsion which indicate that aileron-rolling-effectiveness characteristics are affected adversely by variations in airfoil section which procedure large increases in the trailing-edge angle" (p. 1).

An investigation of the rolling effectiveness at transonic and supersonic speeds of partial-span ailerons on a 42.7 degree sweptback wing having symmetrical circular-arc airfoil sections of 10-percent thickness ratio normal to the wing quarter-chord line has been made by means of rocket-propelled test vehicles. The results are compared with results of a supersonic wind-tunnel test at Mach number 1.9.

Memorandum presenting an approximate subsonic theory developed for the solid blockage interference in circular wind tunnels with walls slotted in the direction of flow. The theory indicated the possibility of obtaining zero blockage interference. Tests in a circular slotted tunnel based on the theory confirmed the theoretical predictions.

Report presenting testing of a 42.7 degree sweptback tapered wing with three types of ailerons tested at a Mach number of 1.9 and a Reynolds number of 2,200,000; the wing geometry was similar to that of an XS-2 airplane. The purpose of the investigation was to determine the effectiveness of ailerons at these specified flight characteristics. Results regarding the aerodynamic characteristics of the wing are also provided.

Results are presented of tests of two specimens tested to study the effect of normal pressure on the critical compressive stress for thin curved sheets. These specimens are designated by their respective rib spacings of 10 inches and 30 inches. The relationship between compressive stress and normal pressure at which buckles disappeared is independent of whether the buckles were made to disappear by increase of normal pressure or decrease of compressive stress. (author).

Report presenting flight measurements of the pressures on the horizontal tail surfaces of a typical propeller-driven pursuit airplane during stalled pull-outs at high Mach number. Unit loads measured on the stabilizer at safe maneuvering limits were not only considerably in excess of the design unit loads, but also occurred in a direction opposite to the design loads. Revision of the tail-load design requirements and manner of specifying safe maneuverability limits to pilots appears necessary.

"A method of predicting equilibrium operating performance of turbojet engines has been developed, with the assumption of simple model processes for the components. Results of the analysis are plotted in terms of dimensionless parameters comprising critical engine dimensions and over-all operating variables. This investigation was made of an engine in which the ratio of axial inlet-air velocity to compressor-tip velocity is constant, which approximates turbojet engines with axial-flow compressors" (p. 673).

An analysis has been made of the drag losses in airplane flight of cross-flow plate and tubular intercoolers to determine the cooling-air weight flow and pressure drop that give a minimum drag loss for any given cooling effectiveness and, thus, a maximum power-plant net gain due to charge-air cooling. The drag losses considered in this analysis are those due to (1) the extra drag imposed on the airplane by the weight of the intercooler, its duct, and its supports and (2) the drag sustained by the cooling air in flowing through the intercooler and its duct. The investigation covers a range of conditions of altitude, airspeed, lift-drag ratio, supercharger-pressure ratio, and supercharger adiabatic efficiency. The optimum values of cooling air pressure drop and weight flow ratio are tabulated. Curves are presented to illustrate the results of the analysis.

The results of an investigation of two 10-foot-diameter, two-blade NACA propellers are presented for a range of blade angles from 20 degrees to 55 degrees at airspeeds up to 500 miles per hour. These results are compared with those from previous investigations of five related NACA propellers in order to evaluate the effects of blade-section thickness ratios on propeller aerodynamic characteristics.

"A general algebraic method of attack on the problem of controlling gas-turbine engines having any number of independent variables was utilized employing operational functions to describe the assumed linear characteristics for the engine, the control, and the other units in the system. Matrices were used to describe the various units of the system, to form a combined system showing all effects, and to form a single condensed matrix showing the principal effects. This method directly led to the conditions on the control system for noninteraction so that any setting disturbance would affect only its corresponding controlled variable" (p. 581).

From Summary: "Results are presented of light tests made to determine the effect of flap deflection on the lateral control characteristics of a modified Brewster F2A-2 airplane equipped with partial-span narrow-chord ailerons on the trailing edge of a full-span NACA slotted flap. The investigation included determination of the rolling and yawing characteristics of the airplane in abrupt aileron rolls with the slotted flap at various settings ranging from 0 degree to about 40 degrees. The results showed that the effectiveness of the ailerons was greatly reduced at flap deflections greater than about 20 degrees. For flap deflections up to about 20 degrees, the aileron effectiveness was about the same as with flaps retracted, but the adverse yawing velocity developed in the abrupt aileron rolls was somewhat increased."

"Flight tests were conducted at the NACA Pilotless Aircraft Research Station, Wallops Island, to determine the characteristics of the Allegany Ballistics Laboratory's 6.2inch-diameter Deacon and 10-inch-scale model solid-propellant rocket motors. The tests were performed to assist in the development of these rockets which were designed for, and urgently needed to propel supersonic research models and pilotless aircraft. The tests showed that the rocket motors functioned properly under various flight- acceleration loads over a range of pre-ignition grain temperatures" (p. 1).

"The J33-A-23 compressor with a 34-blade impeller was operated at ambient inlet temperature and an inlet pressure of 14 inches mercury absolute over a range of equivalent impeller speeds from 6000 to 11,750 rpm. Additional runs at equivalent speeds of 7,000, 10,000, and 11,750 rpm and ambient inlet temperature were made at inlet pressures of 5 and 10 inches mercury absolute. The results of this investigation are compared with those of the J33-A-23 compressor with a 17-blade impeller" (p. 1).

A 1/5.5-size powered dynamic model of the Columbia XJL-1 amphibian was landed in Langley tank no. 1 in smooth water and in oncoming waves of heights from 2.1 feet to 6.4 feet (full-size) and lengths from 50 feet to 264 feet (full-size). The motions and the vertical accelerations of the model were continuously recorded. The greatest vertical acceleration measured during the smooth-water landings was 3.1g.

"A single-stage modification of the turbine from a Mark 25 torpedo power plant was investigated to determine the performance with two nozzle designs in combination with special rotor blades having a 20 inlet angle. The performance is presented in terms of blade, rotor, and brake efficiency as a function of blade-jet speed ratio for pressure ratios of 8, 15 (design), and 20. The blade efficiency with the nozzle having circular pas- sages (K) was equal to or higher than that with the nozzle having rectangular passages (J) for all pressure ratios and speeds investigated" (p. 1).

Flight tests were conducted at the Flight Test Station of the Pilotless Aircraft Research Division at Wallop Island, Va., to determine the longitudinal control and stability characteristics of 0.5-scale models of the Fairchild Lark pilotless aircraft with the tail in line with the wings a d with the horizontal wing flaps deflected 60 deg. The data were obtained by the use of a telemeter and by radar tracking.

Wind-tunnel tests of a full-scale model of the Republic XF-91 airplane were conducted to determine the distribution of pressure over the external wing fuel tank installation and over the vee tail and ventral fin. The data were obtained for a range of angles of attack and sideslip and elerudder deflection angles; the presentation is in tabular form.

Stress-rupture data for four heat-resisting alloys are analyzed according to equations of the theory of rate processes. A method for determining the four parameters of structure and composition is demonstrated and the four parameters are determined for each of the alloys: forged S816, cast S816, cast S590, and cast Vitallium. It is concluded that parameters can be determined for an alloy provided sufficient reliable experimental data are available.

"Investigations were conducted in the Cleveland altitude wind tunnel to determine the performance and operational characteristics of the 19B-2, 19B-8, and 19XS-1 turbojet engines. One objective was to determine the effect of altitude, flight Mach number, and tail-pipe-nozzle area on the performance characteristics of the six-stage and ten-stage axial-flow compressors of the 19B-8 and 19XB-1 engines, respectively, The data were obtained over a range of simulated altitudes and flight Mach numbers" (p. 1).

"The spin and recovery characteristics of the Northrop XF-89 airplane, as well as the spin-recovery parachute requirements, the control forces that would be encountered in the spin, and the best method for the crew to attempt an emergency escape are presented in this report. The characteristics were mainly estimated rather than determined by model tests because the XF-89 dimensional and mass characteristics were such as to make this airplane similar to several others, models of which have previously been tested. Brief tests were made on an available model of similar design to augment the estimation" (p. 1).

Report presenting an analytical study of four combinations of subsonic and supersonic flow in the rotor- and stator-blade passages of axial-flow compressors.

From Introduction: "Performance results of the tail-pipe burning investigation on the TG-180 turbojet engine and a comparison of experimental results with theoretical calculations are presented."

Report presenting an investigation of aileron flutter associated with high-speed flight. When the aileron control system was modified by installing a hydraulic irreversible unit, it was possible to delay aileron flutter and reduce its amplitude. Results regarding the aileron flutter with and without the modifications, analysis of the time histories for the control systems, and relation between aileron upfloat and flutter are provided.

Report presenting calculations based on a theoretical analysis for a composite engine consisting of a uniflow two-stroke-cycle spark-ignition engine, a compressor, a blowdown turbine, and a steady-flow turbine. Operation of the engine is considered for four cases of gas mixtures and steady-flow turbine temperatures.