From Summary: "Pressure distributions and force characteristics have been determined for a body of revolution consisting of a fineness ratio 5.75, circular-arc, ogival nose tangent to a cylindrical afterbody for an angle-of-attack range of 0 degrees to 35.5 degrees. The free-stream Mach number was 1.98 and the free-stream Reynolds number was approximately 0.5 x 10 sup 6, based on body diameter. Comparison of the theoretical and experimental pressure distributions shows that for zero lift, either slender-body theory or higher-order theories yield results which are in good agreement with experiment."

Report discussing the stability and control characteristics and drag of a canard or tail-first configuration explored using the free-fall method. Information about the basic flight characteristics, experimental coefficients, zero-lift drag configurations, and longitudinal stability and trim characteristics is provided.

Stress-rupture data for four heat-resisting alloys are analyzed according to equations of the theory of rate processes. A method for determining the four parameters of structure and composition is demonstrated and the four parameters are determined for each of the alloys: forged S816, cast S816, cast S590, and cast Vitallium. It is concluded that parameters can be determined for an alloy provided sufficient reliable experimental data are available.

Results are presented of tests of two specimens tested to study the effect of normal pressure on the critical compressive stress for thin curved sheets. These specimens are designated by their respective rib spacings of 10 inches and 30 inches. The relationship between compressive stress and normal pressure at which buckles disappeared is independent of whether the buckles were made to disappear by increase of normal pressure or decrease of compressive stress. (author).

Memorandum presenting an investigation of two-dimensional, supersonic cascade-type inlets at a free-stream Mach number of 3.11. Two cascade-type inlets utilizing different methods of internal-flow compression were designed and tested. Results regarding the cascade inlet and stepped-cascade inlet are provided.

Report presenting an investigation of stores on the Douglas D-558-II research airplane in the wind tunnel and in flight using various store configurations. The drag measured for all store configurations was high, from two to three times the free-air drag estimated for the store and pylon. Results regarding longitudinal characteristics and lateral characteristics are provided.

"Measurement of average skin-friction coefficients have been made on six rocket-powered free-flight models by using the boundary-layer rake technique. The model configuration was the NACA RM-10, a 12.2-fineness-ratio parabolic body of revolution with a flat base. Measurements were made over a Mach number range from 1 to 3.7, a Reynolds number range 40 x 10(exp 6) to 170 x 10(exp 6) based on length to the measurement station, and with aerodynamic heating conditions varying from strong skin heating to strong skin cooling" (p. 1).

This report presents the results of a study made of the influence of several variables on the pressure decrease accompanying injection of a relatively cool liquid into a heated compressed gas. Indirectly, this pressure decrease and the time rate of change of it are indicative of the total heat transferred as well as the rate of heat transfer between the gas and the injected liquid. Air, nitrogen, and carbon dioxide were used as ambient gases; diesel fuel and benzene were the injected liquids. The gas densities and gas-fuel ratios covered approximately the range used in compression-ignition engines. The gas temperatures ranged from 150 degrees c. to 350 degrees c.

Investigations were conducted to determine effectiveness of refrigerants in increasing thrust of turbojet engines. Mixtures of water an alcohol were injected for a range of total flows up to 2.2 lb/sec. Kerosene was injected into inlets covering a range of injected flows up to approximately 30% of normal engine fuel flow. Injection of 2.0 lb/sec of water alone produced an increase in thrust of 35.8% of rate engine conditions and kerosene produced a negligible increase in thrust. Carbon dioxide increased thrust 23.5 percent.

"The J33-A-23 compressor with a 34-blade impeller was operated at ambient inlet temperature and an inlet pressure of 14 inches mercury absolute over a range of equivalent impeller speeds from 6000 to 11,750 rpm. Additional runs at equivalent speeds of 7,000, 10,000, and 11,750 rpm and ambient inlet temperature were made at inlet pressures of 5 and 10 inches mercury absolute. The results of this investigation are compared with those of the J33-A-23 compressor with a 17-blade impeller" (p. 1).

"A single-stage modification of the turbine from a Mark 25 torpedo power plant was investigated to determine the performance with two nozzle designs in combination with special rotor blades having a 20 inlet angle. The performance is presented in terms of blade, rotor, and brake efficiency as a function of blade-jet speed ratio for pressure ratios of 8, 15 (design), and 20. The blade efficiency with the nozzle having circular pas- sages (K) was equal to or higher than that with the nozzle having rectangular passages (J) for all pressure ratios and speeds investigated" (p. 1).

From Summary: "A preliminary experimental study was made of the properties of ferrocene as a solute and as a suspension in JP-4 fuel, and of the ignition delays of ferrocene - JP-4 mixture with A.F. specification 14104 white fuming nitric acid (WFNA). The investigation covered concentrations of 4 to 10 percent by weight ferrocene, and a temperature range of -40 to 80 F. The solubility of ferrocene in JP-4 is about 5 percent at room temperature and about 1 percent (extrapolated) at -80 F. The solubility is increased somewhat by increased aromatics content. Undissolved ferrocene particles of 100 mesh and smaller settle rapidly in JP-4."

From Summary: "A simplified analysis is made of the velocity and deceleration history of missiles entering the earth's atmosphere at high supersonic speeds. It is found that, in general, the gravity force is negligible compared to the aerodynamic drag force and, hence, that the trajectory is essentially a straight line. A constant drag coefficient and an exponential variation of density with altitude are assumed and generalized curves for the variation of missile speed and deceleration with altitude are obtained. A curious finding is that the maximum deceleration is independent of physical characteristics of a missile (e.g., mass, size, and drag coefficient) and is determined only by entry speed and flight-path angle, provided this deceleration occurs before impact. This provision is satisfied by missiles presently of more usual interest."

Report presenting a theoretical analysis of a supersonic canard missile configuration to show the means that might be used to improve its dynamic performance characteristics. The analysis was conducted by using the best available estimates of aerodynamic and airframe parameters. Results regarding missile longitudinal performance, selection of rate factor, angle of attack and normal acceleration, frequency response, pole plots, and tip control are provided.

Report discussing testing of a model of the Douglas A4D-1 to determine its low-speed yawing stability derivatives. The model was tested in clean and landing configurations with horizontal and vertical tails on and off and an investigation into the effect of slats and flaps on the wing-alone derivatives.

Report presenting measurements of the longitudinal stability and control characteristics of a canard airplane configuration using the wing-flow method. The investigation included measurements of lift, pitching moment, and rolling moment of the semispan model with control settings between several different degrees. The experimental data are presented in summarized or abridged form and calculated trim curves are presented for various flight loading conditions.