Report presenting lift, drag, and pitching-moment coefficients, lift-drag ratios, and center-of-pressure positions for four airplane-like configurations determined from tests at a range of Mach numbers and angles of attack. The wings and nose shapes were modified for each of the configurations.

Report presenting the results of oscillation tests to measure the dynamic-rotary stability derivatives of an airplane model at high subsonic speeds. Measurements taken included the damping in pitch, damping in yaw, damping in roll, and the yawing moment due to rolling velocity.

"Model investigations were made to determine the ditching characteristics of three typical multiengine airplanes equipped with possible arrangements of hydro-ski ditching gear. The behavior of the models was determined from visual observations, acceleration records, and motion pictures of the landings. Data are presented in tabular form and sequence photographs" (p. 1).

Report presenting an investigation of aileron flutter associated with high-speed flight. When the aileron control system was modified by installing a hydraulic irreversible unit, it was possible to delay aileron flutter and reduce its amplitude. Results regarding the aileron flutter with and without the modifications, analysis of the time histories for the control systems, and relation between aileron upfloat and flutter are provided.

Report discussing an investigation of the effect of spanwise aileron location on the rolling effectiveness of plain faired ailerons on untapered wing plan forms with designated sweep, airfoil sections, and aspect ratio using rocket-propelled test vehicles. Drag data is also presented for all configurations tested. Spanwise aileron location was found to have little effect on the effectiveness of the aileron on an unswept wing plan form.

Report presenting the results of pressure-distribution tests to determine the effects of compressibility on the characteristics of the NACA 66,2-215, 66,2-015, 65(216)-418, 16-212, and 23015 airfoil sections. Schileren photographs of the air flow and data on the wake characteristics was also obtained.

Memorandum presenting an investigation of two annular diffusers of different conical angles of expansion but constant outer diameters with rotating flow behind a fan. The performance characteristics are determined and the rotational-kinetic-energy effects on the overall energy transformation are observed over a range of inlet mach numbers from 0.1 to 0.44 and angles of flow up to 28 degrees.

Report presenting the total drag coefficients of 60 degree cone cylinders of fineness ratio 2.07 measured in free flight from Mach numbers of 1.5 to 8.2. Results regarding the smooth 60 degree cone cylinder, rifled models, and discontinuity lines in the shadowgraph pictures are provided.

Report presenting an investigation of the drag of spherically blunted conical models of fineness ratio 3 at a range of Mach and Reynolds numbers. Results of the tests showed that slightly blunted models had less drag than cones of the same fineness ratio through the Mach number range. Results regarding the total drag, wave drag, and viscous effects are provided.

From Introduction: "Because of the unusual nature of this equipment, and because it is proving to be very useful for certain kinds of aerodynamic research, this report has been prepared. It contains a description of the equipment and its use to obtain aerodynamic coefficients. The imperfections in the wind-tunnel air stream and their effect on model tests are also discussed."

Memorandum presenting the pressure recovery, mass flow, and drag of a twin-scoop, side-inlet-body combination measured at Mach number 1.4 and 1.7. The inlet was located on a body having an ogival nose followed by a cylindrical section and a total fineness ratio of 5.

Report presenting an investigation to determine the ditching characteristics of three typical multiengine airplanes equipped with different arrangements of hydro-ski ditching gear. The behavior was determined from visual observations, acceleration records, and motion pictures of the landings. Results regarding ski size, shape, and location are provided.

From Introduction: "Numerous tests of tip controls on delta wings at transonic and low supersonic speeds have shown that such configurations provide satisfactory rolling-moment effectiveness, and that the hinge can be controlled by proper location of the hinge line (ref. 1). The purpose of the present tests is to determine the characteristics of such a configuration at Mach number of 4.04 and a Reynolds number of 5.8 X 10^6, based on the wing mean aerodynamic chord."

Report presenting an investigation of a configuration of a body of fineness ratio 16.9, an unswept wing of aspect ratio 3, and a taper ratio of 0.4, and incline tail surfaces who was aeropulsed continuously in pitch during free flight with and without a sustainer rocket motor operating. A range of Mach numbers from 0.8 to 2.1 was tested. Results regarding drag, normal force and pitching moment, flow conditions at the horizontal tail, buffeting and model vibrations, and cross coupling are provided.

From Introduction: "This report presents the cooling-air requirements of a "paper" air-cooled turbojet engine operating over a wide range of flight Mach numbers and altitudes. The results are presented for a two-stage-turbine turbo-jet engine having a turbine-inlet temperature of 2500^o R and operating at sea-level static conditions and flight Mach numbers from 0.90 to 2.5 and flight altitudes from 40,000 to 70,000 feet. In addition, the effect of decreasing the blade-inlet cooling-air temperature on the required coolant-flow ratio is presented."

Report presenting an experimental investigation to evaluate combinations of fuselage and inlet throat boundary-layer removal for a ramp-type side inlet in the 8- by 6-foot supersonic wind tunnel at Mach numbers 1.5, 1.8, and 2.0. Optimum combinations of fuselage and inlet throat boundary-layer removal showed gains in available thrust from 3 to 10 percent over the case of no inlet throat bleed. Results regarding variations of diffuser total-pressure distortion, recovery and external drag coefficients, and net gains in available thrust are provided.

From Introduction: "The purpose of this report is to further analyze the turbine performance results of reference 1 with the objective of isolating the contribution of the cooling air to the turbine performance and establishing some systematic relation between these cooling-air effects and the turbine operational parameters."

Report presenting the design details of two transpiration-cooled strut-supported turbine rotor blades. One design uses a sintered blade shell while the other uses a wire blade shell. Ideal coolant flows were found for an effective gas temperature of 1425 degrees Fahrenheit, a coolant temperature of 180 degrees Fahrenheit, and a shell temperature of 600 degrees Fahrenheit.

Report presenting an investigation of a turbojet engine in an altitude test facility to supplement existing data relevant to gas-temperature control in a turbojet engine. The problems associated with gas-temperature control for minimizing turbine-blade damage are considered in the report.

Memorandum presenting a description of the Ames supersonic free-flight wind tunnel, which is a new piece of equipment for aerodynamic research at high supersonic Mach numbers. It has a wide Mach number range extending from low supersonic speeds to Mach numbers in excess of 10. The air stream in the tunnel is imperfect, mainly due to a symmetrical pair of oblique shock waves which reflect down the test section.

From Summary: "The aerodynamic characteristics in pitch of an F-94C airplane, with the primary attention given to its drag characteristics, have been evaluated at low speed in the Ames 40- by 80-foot wind tunnel. The increments of drag due to various surface irregularities, ports, and component parts of the production airplane were determined. Wing-wake surveys were taken to determine the section drag coefficients at midsemispan for the smooth and the production wing. Base-pressure and internal drags of the air-induction system were measured at low inlet-velocity ratios. The characteristics of the airplane in the landing configuration are also included."

"Investigations were conducted in the Cleveland altitude wind tunnel to determine the performance and operational characteristics of the 19B-2, 19B-8, and 19XS-1 turbojet engines. One objective was to determine the effect of altitude, flight Mach number, and tail-pipe-nozzle area on the performance characteristics of the six-stage and ten-stage axial-flow compressors of the 19B-8 and 19XB-1 engines, respectively, The data were obtained over a range of simulated altitudes and flight Mach numbers" (p. 1).