Technical report outlining cavity-type ionization chambers with graphite walls that are used to measure heat dissipation in the graphite reflector of the MTR mock-up. Studies the relationship between the ionization occurring in the chamber and the heat generated in the surrounding graphite medium. [From Abstract]

Technical report covering work completed on the removal of radioisotopes from water using a calcium phosphate floc as a carrier. This research was performed as part of the Health Physics Waste Disposal Research Section work on the removal of small quantities of radioactivity from large volumes of water. [From Abstract]

Technical reports outlining the controls for the Homogeneous Reactor Experiment (HRE); controls are divided into three principal groups. 1. Reactor. 2. Process or auxiliary. 3. Power generation. These are the classifications designating the primary functions of the controls. [From Introduction]

Review of methods by which the radial deposition mechanism was determined in experiments with simulated waste solutions are briefly reviewed.

The preliminary process design of a PRFR pilot leaching plant, which is proposed to be located in Cell B of Building ORNL, is considered. Chemical, physical, and nuclear parameters are investigated in order that the leaching operations may be carried out without any chemical or nuclear hazards.

The Turco 4501 process is recommended for the decontamination of the PRFR pilot leaching plant equipment. The caustic-tartrate-nitric acid process is recommended for the decontamination of the cell and the equipment exterior.

The nil-ductility-transition (NDT) temperature, as defined by the Naval Research Laboratory drop-weight test, was determined on the A212B carbon-silicon steel used in the pressure vessel of the N. S. Savannah nuclear reactor. Correlations were made with the Charpy-V-notch impact energy at NDT. Specimens taken at two different thickness location from materials used in the upper closure head of the reactor vessel yielded NDT temperatures of 0 - 20°F which correspond to Charpy-V-notch impact energies of 11-19 ft-lb. Testing of as-received material used in the lower closure head indicated that the NDT temperature was 50°F which was equivalent to an average Charpy-V-notch impact energy of 12 ft-lb. After normalizing and stress-relieving this material, in order to more closely approximate the final condition of the reactor vessel, NDT was reduced to less than 10°F.

This quarterly progress details ongoing research at the Oak Ridge National Laboratory as a part of the Aircraft Nuclear Propulsion Project. Topics discussed include reactor theory and design, [part two is not included], materials research, and appendixes with information on analytical chemical studies.

The countercurrent gas-liquid system BF3(g)—anisole·BF3(l) for the concentration of boron isotopes has been studied. The single-storage separation factor varies from 1.039 at 0°C to 1.029 at 30°C. Rate of exchange is rapid, and, with efficient contacting equipment, complete exchange may be obtained in less than 15 sec. A total separation of 1.525 has been realized in laboratory equipment. The critical-product reflux reaction is quite efficient. Only about 55 moles of BF3 remain in each million moles of effluent solvent under laboratory conditions. The vapor pressure of BF3 over the complex rises sharply as the temperature is increased. At 0°C the pressure is 150 mm Hg, and at 40°C the pressure has risen to 1800 mm Hg. From vapor-pressure measurements, an approximate upper limit of ΔH= -12kcal per mole of complex was calculated for the reaction [equation not transcribed]. Qualitative tests indicate good resistance of anisole to decomposition by BF3 under plant conditions. The uncatalyzed exchange of boron between BF3 and BCl3 was found to be too slow to be exploited in a countercurrent system. The single-stage, equilibrium separation factor for the Nitrox system is a function of acid concentration. At 26°C the factor ranges from 1.064 with 1 M acid …

Report documenting the design and testing progress of the Oak Ridge National Laboratory's Gas-Cooled Reactor Program.

Report that describes the Oak Ridge National Laboratory Experimental Gas-Cooled Reactor, problems with the procurement and assembly of its components, and its economic feasibility.

The flux through a given region is proportional to the total lengths of the neutron flight paths that intersect that region. The analytical Monte Carlo procedure manufactured neutron flight paths and totaled the lengths of all paths intercepted by the regions illustrated in Figure 1. The procedure was designed to utilize the various symmetries in the lattice. / Consider a portion of the lattice whose planar cross-section is shown in Figure 5. If R is the region in which the flux is to be estimated and F the fuel rod in which the neutron originated, then flight path P results in an intercepted length whose reflection in the plane is L. On the other hand flight path P' intercepts R' with length L'. R' is not the region to be studied, but a translation of the flight path P' to F' would result in the neutron intercepting R. The origin in P was arbitrary. For each neutron originating in P another could, with equal probability, have originated in P' with parallel paths. Hence consulting L' in R' towards the total flux is equivalent to starting a neutron at P'. Thus consideration of all regions symmetric to R with respect to …

The use of the DD^3 amplifier with the RIDL 200- and 400-channel analyzers has been found advantageous for certain applications. In order to use the DD2, certain modifications to the input circuits of the Analog-to Digital Converter Unit are necessary. In addition, the modifications improved the linearity of the analyzer in the low channels. Using the analyzer with the RIDL Type 30-7 Scintillation Pulse Amplifier, it was noted that non-linearity of as much as 5 or 6 channels was present below channel 20. With the modifications made and with the use of the DD2, this non-linearity has been reduced to less than 1/2 channel.

At the request of the Alloy Preparation Group, the Nondestructive Test Development Group investigated the feasibility of determining the clad thickness on Mark X MTR Fuel Plates. As the use of induced eddy-currents was considered to be the most promising approach, a prototype instrument and probe coil utilizing this principle was developed to measure clad thickness. The results of the investigation conducted with this instrument indicate that the clad thickness of this type of fuel plats can be measured to withing +- 0.001 in.

The equilibrium and maximum override values for xenon and samarium poisoning have been computed using the recently issued effective cross sections of C. H. Westcott. Values are given as a function of specific power, neutron temperature, and epithermal flux content.