An interfacial viseometer was built for use in an interfacial phenomena study. Installation of a 6-in.-ID foam separation column system was completed. The dispersiondrying-sintering characteristics of six low-nitrate batches of thoria sol material were studied. The average effective porosity of the CuO pellets used for reactor helium purification was determined to be 0.0545 for H/ sub 2/ transport and 0.0526 for CO transport. In continuous Zirflex dissolution studies, no H/sub 2/O/sub 2/ decomposition was observed when 10% H/sub 2/O/sup 2 was fed into boiling dissoivent through a water-cooled nozzle and the oxygen concentration in the scrubbed off-gas could be used to control the H/sub 2/O/sub 2/ concentration in the dissolver. The free fluoride in Zirflex solutions must be maintained above 1 molar in order to prevent uranium precipitation at low concentrations of uranium even though the F/sup -//U ratio exceeds 100. Chopped stainless steel-clad UO/sub 2/ sections were leached in a 4 stage pyrex leacher model using 6, 7, and 8 M nitric acid as the dissolvent. The temperature distribution expected within fuel elements consisting of square arrays of tubes was calculated for shipping conditions assuming heat to be transferred only by radiation. HETS values were calculated for uranium stripping …

Measurement of beam properties at the foci of high energy linacs is difficult due to the small size of the waists in proposed and existing accelerators (1 nm {minus} 2 {mu}). This paper considers the use of bremsstrahlung radiation from thin foils to measure the size and phase space density these beams using nonimaging optics. The components of the system are described, and the ultimate resolution, evaluated theoretically for the case of the Final Focus Test Beam at Stanford Linear Accelerator Center, is a few nm. 13 refs., 4 figs. 1 tab.

A stress analysis of the 3/8-inch and 1/4-inch pins which hold the rake assembly to the flange was performed and shows stresses to be lower than the Class 1 allowables of the ASME Boiler and Pressure Vessel Code. The alternating pin stresses were found to be below the endurance limit and fatigue failure will not occur. The rake assembly was assumed to be loaded by steady drag and lift forces and alternating vortex shedding forces.

The objective of this presentation is to: (1) present the physical motivation for fusion-fission hybrids, (2) outline design considerations for hybrid blankets, and (3) discuss the nuclear performance potential of hybrid blankets.

Eight appendices address the following concentrations of radionuclides: in fish; in frog legs; in crayfish; in sediments; in soil samples; in surface and ground water samples; in water hyacinths; and in beef samples.

Results from calculations of focal spot size for beam transport through a gas-filled reactor are summarized. In the converging beam mode, we find an enlargement of the focal spot due to multiple scattering and zeroth order self-field effects. This enlargement can be minimized by maintaining small reactors together with a careful choice of the gaseous medium. The self-focused mode, on the other hand, is relatively insensitive to the reactor environment, but is critically dependent upon initial beam quality. This requirement on beam quality can be significantly eased by the injection of an electron beam of modest current from the opposite wall.

The Department of Energy has authorized a team of glass formulation and processing experts at the Savannah River National Laboratory (SRNL), the Pacific Northwest National Laboratory (PNNL), and the Vitreous State Laboratory (VSL) at Catholic University of America to develop a systematic approach to increase high level waste melter throughput (by increasing waste loading with minimal or positive impacts on melt rate). This task is aimed at proof-of-principle testing and the development of tools to improve waste loading and melt rate, which will lead to higher waste throughput. Four specific tasks have been proposed to meet these objectives (for details, see WSRC-STI-2007-00483): (1) Integration and Oversight, (2) Crystal Accumulation Modeling (led by PNNL)/Higher Waste Loading Glasses (led by SRNL), (3) Melt Rate Evaluation and Modeling, and (4) Melter Scale Demonstrations. Task 2, Crystal Accumulation Modeling/Higher Waste Loading Glasses is the focus of this report. The objective of this study is to provide supplemental data to support the possible use of alternative melter technologies and/or implementation of alternative process control models or strategies to target higher waste loadings (WLs) for the Defense Waste Processing Facility (DWPF)--ultimately leading to higher waste throughputs and a reduced mission life. The glass selection strategy discussed …

We propose to combine and slightly extend two existing 'Les Houches Accords' to provide a simple generic interface between beyond-the-standard-model parton-level and event-level generators. All relevant information--particle content, quantum numbers of new states, masses, cross sections, parton-level events, etc.--is collected in one single file, which adheres to the Les Houches Event File (LHEF) standard.

The XRD-31 is a fast, windowless X-ray vacuum photodiode developed by EG&G. It is currently the primary fast X-ray detector used to diagnose the X-rays on NIF and OMEGA on the multichannel DANTE spectrometer. The XRD-31 has a dynamic range of less than 1e-12 amps to more than 10 amps. A technique is described to measure the impulse response of the diodes to a 150 fs pulse of 200 nm laser light and a method to calculate the “risetime” for a square pulse and compare it with the computed electron transit time from the photocathode to the anode. Measured response time for 5 XRD-31s assembled in early 2004 was 149.7 ps +-2.75 ps.

Soft x-ray zone plate microscopy has proven to be a valuable imaging technique for nanoscale studies. It complements nano-analytic techniques such as electron and scanning probe microscopies. One of its key features is high spatial resolution. We developed an overlay nanofabrication process which allows zone plates of sub-20 nm zone widths to be fabricated. Zone plates of 15 nm outer zones were successfully realized using this process, and sub-15 nm resolution was achieved with these zone plates. We extend the overlay process to fabricating zone plates of 12 nm outer zones, which is expected to achieve 10 nm resolution. In addition, we have identified a pathway to realizing sub-10 nm resolution, high efficiency zone plates with tilted zones using the overlay process.

Failure occurs when one or more of the intended functions of a product are no longer fulfilled to the customer's satisfaction. The most critical product failures are those that escape design reviews and in-house quality inspection and are found by the customer. The product may work for a while until its performance degrades to an unacceptable level or it may have not worked even before customer took possession of the product. The end results of failures which may lead to unsafe conditions or major losses of the main function are rated high in severity. Failure Modes and Effects Analysis (FMEA) is a tool widely used in the automotive, aerospace, and electronics industries to identify, prioritize, and eliminate known potential failures, problems, and errors from systems under design, before the product is released (Stamatis, 1997). Several industrial FMEA standards such as those published by the Society of Automotive Engineers, US Department of Defense, and the Automotive Industry Action Group employ the Risk Priority Number (RPN) to measure risk and severity of failures. The Risk Priority Number (RPN) is a product of 3 indices: Occurrence (O), Severity (S), and Detection (D). In a traditional FMEA process design engineers typically analyze the 'root …

This annual report provides details on the research conducted at EMSL--the Environmental Molecular Sciences Laboratory in Fiscal Year 2008.

A two-stage gas release model was examined to determine if it could provide a physically realistic and accurate model for fission gas release under Prometheus conditions. The single-stage Booth model [1], which is often used to calculate fission gas release, is considered to be oversimplified and not representative of the mechanisms that occur during fission gas release. Two-stage gas release models require saturation at the grain boundaries before gas is release, leading to a time delay in release of gases generated in the fuel. Two versions of a two-stage model developed by Forsberg and Massih [2] were implemented using Mathcad [3]. The original Forsbers and Massih model [2] and a modified version of the Forsberg and Massih model that is used in a commercially available fuel performance code (FRAPCON-3) [4] were examined. After an examination of these models, it is apparent that without further development and validation neither of these models should be used to calculate fission gas release under Prometheus-type conditions. There is too much uncertainty in the input parameters used in the models. In addition. the data used to tune the modified Forsberg and Massih model (FRAPCON-3) was collected under commercial reactor conditions, which will have higher fission …

Forty one years ago, September 20, 1966, the first beam entered End Station A, passed on through, and was terminated in Beam Dump East. This beam had an energy of 18.4 GeV, a record for the time. Since then, the SLAC ESA has been a mainstay facility for many high-energy physics and test beam experiments involving countless hours of data taking. Heretofore, it was assumed that with the completion and commissioning of the LCLS facility, beams from the main injector would no longer be available to this well equipped experimental facility. Fortunately, it has become clear that a bypass beamline design calling for modest modifications and using existing, soon to be surplus, components will enable continued utilization of this important facility.

In an attempt to predict the creep deformation of spent nuclear fuel cladding under the repository conditions, different correlations have been developed. One of them, which will be referred to as Murty's correlation in the following, and whose expression is given in Henningson (1998), was developed on the basis of experimental points related to unirradiated Zircaloy cladding (Henningson 1998, p. 56). The objective of this calculation is to adapt Murty's correlation to experimental points pertaining to irradiated Zircaloy cladding. The scope of the calculation is provided by the range of experimental parameters characterized by Zircaloy cladding temperature between 292 C and 420 C, hoop stress between 50 and 630 MPa, and test time extending to 8000 h. As for the burnup of the experimental samples, it ranges between 0.478 and 64 MWd/kgU (i.e., megawatt day per kilogram of uranium), but this is not a parameter of the adapted correlation.

The purpose of this analysis is to select the critical characteristics to be verified for steel sets and accessories and the verification methods to be implemented through a material dedication process for the procurement and use of commercial grade structural steel sets and accessories (which have a nuclear safety function) to be used in ground support (with the exception of alcove ground support and alcove opening framing, which are not addressed in this analysis) for the Exploratory Studies Facility (ESF) Topopah Spring (TS) Loop. The ESF TS Loop includes the North Ramp, Main Drift, and South Ramp underground openings.

We present the results of our measurements of the electron cloud density in the PEP-II low energy ring (LER) by propagating a TE wave into the beam pipe. By connecting a signal generator to a beam position monitor button we can excite a signal above the vacuum chamber cut-off frequency and measure its propagation through the beam pipe with a spectrum analyzer connected to another button about 50 meters away. The measurement can be performed with different beam conditions and also at different settings of the solenoids used to reduce the build up of electrons. The presence of a modulation in the TE wave transmission, synchronous with the beam revolution frequency, which appear to increase in depth when the solenoids are switched off, seem to be directly correlated to the electron cloud density in the region between the two BPM's. In this paper we present and discuss the measurements taken in the Interaction Region 12 straight of the LER during 2006 and the first part of 2007.

The Linac Coherent Light Source (LCLS), currently under design, requires accurate alignment between the electron beam and each undulator's magnetic centerline. A beam finder wire (BFW) instrument has been developed to provide beam location information that is used to move the undulators to their appropriate positions. A BFW instrument is mounted at each of the 33 magnets in the undulator section. Beam detection is achieved by electrons impacting two carbon fiber wires and then sensing the downstream radiation. The wires are mounted vertically and horizontally on a wire card similar to that of a traditional wire scanner instrument. The development of the BFW presents several design challenges due to the need for high accuracy of the wires locations and the need for removal of the wires during actual operation of the LCLS (30 microns repeatability is required for the wire locations). In this paper, we present the technical specification, design criteria, mechanical design, and results from prototype tests for the BFW.

A mathematical model of entry-time processes was developed, and a computational method for solving that model was verified. This methodology was demonstrated via application to a succession of increasingly more complex subsystems of nuclear power plants. The effort culminated in the application to main generators that constituted the PhD dissertation of Shuwen (“Eric”) Wang. Dr. Wang is now employed by ABS Consulting, in Anaheim, CA. ABS is a principal provider to the nuclear industry of technical services related to reliability and safety.

This report is the second of a series of studies to evaluate research and development (R&D) projects funded by the Automotive Lightweighting Materials (ALM) Program of the Office of Advanced Automotive Technologies (OAAT) of the U.S. Department of Energy (DOE). The objectives of the program evaluation are to assess short-run outputs and long-run outcomes that may be attributable to the ALM R&D projects. The ALM program focuses on the development and validation of advanced technologies that significantly reduce automotive vehicle body and chassis weight without compromising other attributes such as safety, performance, recyclability, and cost. Funded projects range from fundamental materials science research to applied research in production environments. Collaborators on these projects include national laboratories, universities, and private sector firms, such as leading automobile manufacturers and their suppliers. Three ALM R&D projects were chosen for this evaluation: Design and Product Optimization for Cast Light Metals, Durability of Lightweight Composite Structures, and Rapid Tooling for Functional Prototyping of Metal Mold Processes. These projects were chosen because they have already been completed. The first project resulted in development of a comprehensive cast light metal property database, an automotive application design guide, computerized predictive models, process monitoring sensors, and quality assurance methods. …

This multi-investigator project was concerned with the development and application of new methods and computer codes that would allow realistic modeling of nanosystems. Carter's part in this team effort involved two method/algorithm/code development projects during the first 14 months of this grant. Carter's group has been advancing theory and applications of the orbital-free density functional theory (OF-DFT), the only DFT method that exhibits linear scaling for metals. Such a method offers the possibility of simulating large numbers of atoms with quantum mechanics, such that properties of metallic nanostructures (e.g. nanowires of realistic dimensions) could be investigated. In addition, her group has been developing and applying an embedded correlated wavefunction theory for treating localized excited states in condensed matter (including metals). The application of interest here is spin manipulation at the nanoscale, i.e., spintronics, in which local electron excitations interact with the surrounding material. Her embedded correlation method is ideal for studying such problems.

The title compound C{sub 81}H{sub 88}BF{sub 3}N{sub 6}O{sub 5}SYb{sub 2}, crystallizes as a half-sandwich complex with a bridging inner-sphere trifluoro-methane sulfonate as well as two bridging hydroxide groups. there is uncoordinated 5,5{prime}-dimethyl-2,2{prime}-bipyridine in the crystal structure. The bound bipyridine ligands have N-C-C{prime}-n{prime} torsion angles of 12-13{sup o}. The triply bridged Yb centers are 3.5990(4) Angstroms apart. The Yb-N bonds range from 2.389(6)-2.424(5) Angstroms.

The resummation of soft gluon exchange for QCD hard scattering requires a matrix of anomalous dimensions, which has been computed through two loops. The two-loop matrix is proportional to the one-loop matrix. Recently there have been proposals that this proportionality extends to higher loops. One can test such proposals by computing the dependence of this matrix on the matter content in a generic gauge theory. It is shown that for the matter-dependent part the proportionality extends to three loops for arbitrary massless processes.

In this paper we present the design of the beam position monitor (BPM) system for the LCLS undulator, which features a high-resolution X-band cavity BPM. Each BPM has a TM{sub 010} monopole reference cavity and a TM{sub 110} dipole cavity designed to operate at a center frequency of 11.384 GHz. The signal processing electronics features a low noise single-stage three-channel heterodyne receiver that has selectable gain and a phase locking local oscillator. We will discuss the system specifications, design, and prototype test results.