This paper gives a cost breakdown of all the water facilities in the 100-F area for the month of January, 1948. Also given is the cost of chlorine for addition to the process water system along with where it is added and in what amounts. Lastly, the average figure for the hardness for the Columbia River water at Hanford.

On August 21, 1948, several smear samples of contamination from the inner rod room at 100-F Area were submitted for beta identification. This contamination was spread as a result of maintenance work on the horizontal rods. Urine sample were deemed advisable for two men who had been exposed while working on the rods. These urine samples were also submitted for beta analyses. The analyses of the smears showed the contamination to consist of primarily S{sup 35} (65%) and Fe{sup 59} (30%)and minor amounts of Ca (5%) and C{sup 14} (3%). No significant amount of radio iron or sulfur was found in either the feces or urine samples.

None

None

An investigation conducted in the icing research tunnel to determine aerodynamic and icing characteristics of two flush-inlet-type fuel cell vent installations. The vent tubes were mounted in two different locations in the two installations. The vents were aerodynamically investigated to obtain vent-tube static-pressure differentials and pressure surveys as a function of tunnel-air velocity and angle of attack.

Report presenting an investigation of the pressure distributions over the drooped-nose flap of a 42 degree sweptback wing with circular-arc airfoil sections and half-span trailing-edge split flaps in the 19-foot pressure tunnel. The effects of the deflection and span of the drooped-nose flap and effects of split trailing-edge flaps on the pressures over the drooped-nose flap were determined.

Report discusses the results of an investigation into the aerodynamic characteristics of models of a tailless, pursuit-type, supersonic airplane employing a wing of triangular plan form. Measurements of lift, drag, and pitching moment, side force, drag, and yawing moment are described for several angles of attack and angles of yaw. Information about elevator and rudder behavior is also described.

Report discussing an aerodynamic control effectiveness study using free-flight, rocket-propelled test vehicles. Information about the effects of wing sweepback, aspect ratio, taper ratio, and section thickness ratio on the rolling effectiveness of full-span, sealed ailerons is provided.

From Summary: "The effects of externally mounted rockets and fuel tanks on the aerodynamic characteristics of an airplane model with a swept-back wing are presented in this report."

Report presenting an investigation using the NACA wing-flow method to determine the longitudinal stability and control characteristics at transonic speeds of a semispan airplane with a 45 degree sweptback wing and tail. Measurements of the lift and angle of attack for trim were made for several stabilizer and elevator settings. Testing was also performed to investigate the effects of transition wires mounted on the wing and tail, the effect of increasing the boundary-layer thickness on the test surface, and the effectiveness of a wing flap with a sweepback of 45 degrees.

Memorandum presenting some pressure-distribution and boundary-layer measurements made in flight in the presence of shock on two modifications of the local contour of the wings of a high-speed airplane. Results regarding the pressure distribution, boundary-layer surveys, and effects on test airplane are provided.

The vibration characteristics of a group of axial-flow compressor blades of similar geometry were investigated. Empirical-mode constants were determined for the first three bending and torsional modes. A comparison of experimentally determined frequencies of a second group of blades with frequencies computed using these mode constants showed that the computed values were correct within 10 percent. The approximate limiting ratios of depth to chord and length to chord below which these constants could not be used to compute the natural frequencies were also found experimentally.

Report presenting the results of an estimation of the limit forces on airfoils at supersonic speeds. The limit pressure coefficient attainable on an airfoil is shown to be about 70 percent of the pressure coefficient for a vacuum over a wide range of Mach numbers.

Two low-acceleration transonic-flutter vehicles were launched and flown. The first carried two test wings, one of which fluttered at M = 0.92 at a frequency of 61.4 cycles per second. The reference flutter speed determined from two-dimensional theory for an unswept wing in incompressible flow is conservative when compared to the experimental flutter speed. The second vehicle carried two test wings, one of which failed at M = 0.71 because of low-frequency divergent oscillation. Since this failure was not caused by conventional flexure-torsion flutter, no comparison with a reference flutter speed can be made.

Report presenting an investigation of burner liners in a turbojet engine to determine the principal factors limiting the burner-liner service life. The investigation covered a range of engine speeds and testing was conducted to determine whether bare, ceramic-coated, or shielded thermocouples would give the most correct temperature readings.

Report presenting several rectangular and tapered wing configurations with leading-edge and trailing-edge ailerons tested as part of a general investigation of an aerodynamic control at supersonic speeds. Results indicated that the use of the leading-edge aileron alone was ineffective or caused negative control until a high Mach number was attained. Results for the untapered configurations, tapered configurations, and drag measurements are provided.

An X-ray - diffraction analysis of residual surface stresses after plastic strain was introduced in a parallel-sided 3S-O aluminum disk with a central hole by two types of centrifugal overspeed is reported. Both tangential and radial stresses were generally tensile with large local variations near the hole where surface stresses may have been partly superficial. These stresses were both tensile and compressive dependent on the distance from the disk center when mass compression was effected near the hole.

Report presenting results obtained to determine the effects of compressibility at high Mach numbers on a scale model of the Bell XS-1 transonic research airplane. The results are presented for several model configurations through a range of Mach numbers. Results regarding aerodynamic characteristics and static longitudinal stability characteristics are provided.

"The stability derivatives valid for a limited range of supersonic speeds are presented for a series of sweptback wings tapered to a point with sweptback or sweptforward trailing edges. These wings were derived by modifying the trailing edge of a basic triangular wing so that it coincided with lines drawn from the wing tips to the wing axis of symmetry. The stability derivatives were formulated by using the pressure distributions previously obtained for the basic triangular wing for angle of attack, constant vertical acceleration, sideslip, pitching, rolling, and yawing" (p. 411).

Routine inspections of selected Van Stone flanges have been made at all three piles since start-up. In September, 1947, these inspections indicated that corrosion effects were becoming dangerously severe. Some of the flanges appeared to be corroied and pitted to a depth of two-thirds of the original flange thickness. To determine the extent and severity of the corrosion, residual flange thickness measurements were made on the flanges of about 64 scattered tubes. Included were front and rear flanges of tubes from all four orifice zones. Results of the survey indicated the immediate need for an extensive repair program to preclude the possibility of failure of some of the flanges.

"An investigation has been conducted in the NACA Cleveland altitude wind tunnel to evaluate the performance and windmilling drag characteristics of an original and a modified turbojet engine of the same type. Data have been obtained at simulated altitudes from 5000 to 45,000 feet, simulated flight Mach numbers from 0.09 to 1.08, and engine speeds from 4000 to 12,500 rpm. Engine performance data are presented for both engines to show the effects of altitude at a flight Mach number of 0.25 and of flight Mach number at an altitude of 25,000 feet" (p. 1).

Combustion chamber performance properties of a 3000-pound-thrust axial-flow turbojet engine were determined. Data are presented for a range of simulated altitudes from 15,000 to 45,0000 feet and a range of Mach numbers from 0.23 to 1.05 for various modifications of the engine.

An investigation was conducted to evaluate the operational characteristics of a 3000 pound thrust axial flow turbojet engine over a range of simulated altitudes from 2000 to 50,000 feet and simulated flight Mach numbers from 0 to 1.04 throughout the operable range of engine speeds. Engine operating range, acceleration, deceleration, starting, altitude, and flight Mach number compensation of the fuel control system, and operation of the lubrication system at high and low ambient air temperatures were evaluated.

A wind tunnel investigation was conducted to determine the performance of a turbine operating as an integral part of a turbojet engine. Data was obtained while the engine was running over full operable range of speeds at various altitudes and flight mach numbers, and with four nozzles of different outlet areas.A maximum turbine efficiency of 0.875 was obtained at altitude of 15 thousand feet, Mach number 0.53, and corrected turbine speed of 5900 rpm.