Report presenting the results of an investigation of flap-type controls on a low-aspect-ratio triangular wing using NACA 0005-63 sections for a constant-chord and a constant-percent-chord control surface. Two flap profiles were investigated: one with a true contour and the other with a blunt trailing edge. Results regarding lift, drag, pitching moment, hinge moment, and rolling moments were obtained for several Mach numbers, a constant Reynolds number, and a range of angles of attack.

Report presenting the effects of variation of trailing-edge angle and trailing-edge thickness on the lift characteristics of a 10-percent-chord thick symmetrical NACA airfoil section with a 25-percent-chord plain flap as determined from wind tunnel tests over a range of Mach numbers. Results regarding the section lift and pitching-moment characteristics, variation of lift coefficient with flap deflection, schileren photographs, and effect of angle of attack are provided.

Report presenting an investigation of a supersonic aircraft configuration and various combinations of its components at a range of Mach numbers. Longitudinal- and lateral-force characteristics of the configurations, as well as longitudinal- and lateral-stability derivatives, are provided.

Report presenting measurements of wing and fuselage pressure distributions made at low and high subsonic Mach numbers on a scale model of the projected X-3 research airplane. Tests were conducted in pitch and yaw and included measurements of the total pressure in the fuselage boundary layer at the location of the left boundary-layer bleed scoop.

"An investigation was conducted to determine the effectiveness of area suction used to delay the separation of air flow at the leading edge of a 63 degree swept-back wing. Changes in lift, drag, and pitching-moment data were correlated with the occurrence of the separation of the air flow by means of pressure-distribution data. It was found that the spanwise and the chordwise extent of area suction required to control leading-edge separation were in general agreement with that predicted by theory, but the quantity of flow required was considerably higher than predicted by theory" (p. 1).

Memorandum presenting an investigation of a 2:1 area ratio conical diffuser of length equal to the inlet diameter with separate variation of several basic parameters for simple nontwisted counterrotating rectangular vortex generators over a considerable range of inlet-boundary-layer thickness. The maximum values of static-pressure rise were determined for angle of attack, spacing, aspect ratio, and span-to-inlet boundary-layer thickness. Results for the diffuser with no vortex generators, effects of selectable vortex-generator variables, effect of inlet-boundary-layer displacement thickness, and use of the maximum indicated vortex-generator design values are provided.

Memorandum presenting flutter tests of untapered, low-aspect-ratio, sweptback-wing models and of triangular-wing models of solid magnesium, aluminum, and steel construction in an intermittent supersonic wind tunnel at Mach number 1.3. Flutter data are presented for 31 sweptback wing models and 24 triangular-wing models. The flutter boundaries are indicated on plots of streamwise thickness ratio and aspect ratio.

Memorandum presenting a method for calculating the stick-fixed longitudinal stability of a wing-fuselage configuration at subcritical Mach numbers. The method applies to unswept- and swept-wing configurations. The stability parameters estimated by the method show reasonable agreement with the experimental values for the 23 configurations used in the comparison.

Report presenting effects of wing trailing-edge bluntness on aerodynamic characteristics of a wing-body combination at a range of Mach numbers and Reynolds numbers. Modifications were made to the rear half of a basic plane tapered wing of aspect ratio 3.1 and a 3-percent-thick, circular-arc, biconvex section with three types of trailing-edge shapes. Results regarding the lift characteristics, pitching-moment characteristics, drag characteristics, and maximum lift-drag ratio are provided.

Testing occurred using the NACA wing-flow method at a range of Mach numbers to determine the effect on aerodynamic characteristics of reversing a triangular wing with a 6-percent-thick biconvex section. Results regarding the lift characteristics, drag characteristics, and pitching-moment characteristics are provided.

Report presenting an investigation of the longitudinal characteristics of a wing with 45 degree sweepback of the quarter-chord line, an aspect ratio of 8, a taper ratio of 0.45, and NACA 63(sub)1A012 airfoil sections. The results were obtained from force measurements and distribution measurements for a range of Reynolds numbers. Information regarding lift and pitching-moment characteristics, drag characteristics, and loading characteristics is provided.

From Summary: "A procedure is presented for determining boundary-layer quantities from pressure-rake data, which include the combined effects of viscous and shock losses. The problem is analyzed using schileren photographs of the shock configuration, the continuity of mass relationship, and the characteristic of the turbulent boundary layer that its outer edge is defined by a rapid change in slope in the Mach number profiles in the vicinity of the edge."

The effects of fineness ratio (14.2 and 12.2) and boattailing on aerodynamic characteristics of four bodies of revolution at Mach numbers from 1.50 to 1.99 within a range of angles of attack from 0 degrees 10 degrees at an approximate Reynolds number of 35x10(superscript)6 based on body length were investigated. A comparison of experimental data with available theory is included. At zero angle of attack, fineness ratio has no appreciable effect on model characteristics while boattailing and boattail convergence significantly affect fore drag and base drag.

Report presenting propeller-blade torsional-deflection data obtained during an investigation of the pressure distribution on constant-chord solid aluminum-alloy blades differing only in camber and thickness. Testing indicated that thinner blades were able to produce greater amounts of deflection. Results regarding torsional deflections are also provided.

The factors affecting the performance of ejector suitable for aircraft cooling are investigated theoretically and experimentally. The investigation covers a range of shroud-to-nozzle diameter ratios from 1.1 to 1.6, of shroud lengths from 0.2 to 2.28 nozzle diameters, of secondary-to-primary weight-flow ratios from 0 to 0.12, and of ambient-to-nozzle pressure ratios from 0.7 to 0.06. The results of a simplified theoretical analysis based on each type of flow are in good agreement with those experimentally obtained.

Report presenting an investigation at Mach number 1.61 to determine the hinge-moment characteristics of seven tip controls on a 60 degree sweptback delta wing. Testing occurred over a range of angles of attack and control deflection. The results indicated that the most important parameter in designing delta-wing tip control is the ratio of control-surface area ahead of the hinge line to total control-surface area.

Report presenting results from a limited flight program to obtain information on airplane response and actual rates and amounts of control motion used by service pilot in performance of squadron operational training. Results regarding control deflection, control rates, airplane angular velocities, airplane angular accelerations, angle of attack and angle of sideslip, airplane load factors, and airspeed and altitude are provided.

"During the flight investigation of the X-1 airplane the hinge moments of the elevator and aileron control surfaces have been measured over a Mach number range extending to above 1.0. The results of these measurements are presented in this paper" (p. 2).

Report presenting combustion-efficiency data for a 5-inch ramjet-type combustor using a simple V-gutter flame holder. Data for homogeneous fuel-air mixtures of 14 pure fuels and 3 fuel blends cover a range of inlet static pressures and velocities.

From Introduction: "This report presents the initial study, the tracking performance of typical fighter airplanes with fixed gunsights. The types of airplanes tested afford two comparisons of particular interest: that between typical World War II and currently operational fighters of greatly increased speed and altitude, and that between conventional and irreversabile power-boosted controls with artificial feel, both installed on the same airframe."

Report presenting an investigation in the 4- by 4-foot supersonic pressure tunnel to determine the effects of body contouring as specified by the transonic drag-rise area rule on the aerodynamic characteristics of a delta wing-body combination at Mach numbers of 1.41 and 2.01. Body contouring reduced zero-lift drag of a delta wing-body combination from that of a basic wing-body combination without contouring by 18 percent at Mach number 1.41 and 6 percent at Mach number 2.01. Results regarding the characteristics at zero lift and characteristics for the lifting condition are provided.

Report presenting testing of a shielded total-pressure tube with a curved venturi entry in order to obtain the variation of total-pressure error with angle of attack from a range of 0 to 60 degrees and for a range of Mach numbers. The critical angle was found to vary from about 57 degrees at Mach number 0.90 to 56 degrees at Mach number 1.10.

A summary of some effective aerodynamic twisting-moment coefficients of various wing-control configurations for use at a range of Mach numbers. The values obtained were determined by the combined use of experimentally determined free-flight data and subsonic aerodynamic theory.

Memorandum presenting an investigation of modifications to an indented body which was originally designed on the basis of the transonic drag-rise rule to determine the effects on the aerodynamic characteristics of a 45 degree sweptback-wing-body combination. The investigation covered a range of Mach numbers and angles of attack. Results regarding lift, drag for the nonlifting case, drag for the lifting case, maximum lift-to-drag ratios, and pitching moment are provided.