Report presenting the results of an investigation of flap-type controls on a low-aspect-ratio triangular wing using NACA 0005-63 sections for a constant-chord and a constant-percent-chord control surface. Two flap profiles were investigated: one with a true contour and the other with a blunt trailing edge. Results regarding lift, drag, pitching moment, hinge moment, and rolling moments were obtained for several Mach numbers, a constant Reynolds number, and a range of angles of attack.

Report presenting effects of wing trailing-edge bluntness on aerodynamic characteristics of a wing-body combination at a range of Mach numbers and Reynolds numbers. Modifications were made to the rear half of a basic plane tapered wing of aspect ratio 3.1 and a 3-percent-thick, circular-arc, biconvex section with three types of trailing-edge shapes. Results regarding the lift characteristics, pitching-moment characteristics, drag characteristics, and maximum lift-drag ratio are provided.

Report presenting testing of a shielded total-pressure tube with a curved venturi entry in order to obtain the variation of total-pressure error with angle of attack from a range of 0 to 60 degrees and for a range of Mach numbers. The critical angle was found to vary from about 57 degrees at Mach number 0.90 to 56 degrees at Mach number 1.10.

Report presenting an investigation of the performance of several conical cooling-air ejectors at primary jet pressure ratios from 1 to 10, secondary shroud pressure ratios from 0.60 to 4.00, and primary to secondary temperature ratio of 1.0. The investigation centered on primary air flow, secondary air flow, primary nozzle thrust, and gross ejector thrust.

From Summary: "Ogive-cylindrical fuselages of fineness ratio 11 have been flight-tested with and without stabilizing fins. Base-pressure measurements over a range of free-stream Mach numbers from 0.7 to 1.3 indicated that the fins reduced the base drag. A rear-support sting similar to those used in wind tunnels was tested with one of the fuselages and found to reduce base suction by 40 percent at subsonic speeds, but to have little effect at Mach numbers above 1.15."

Report presenting an investigation of the effect of Reynolds number and the addition of leading-edge roughness on the aerodynamic characteristics of wings with aspect ratio 1, 2, and 3, a rectangular plan form, square-cut wing tips, and NACA 0012 airfoil sections. Results regarding lift and moment, lift-curve slope, and maximum lift are provided.

Memorandum presenting a method for calculating the stick-fixed longitudinal stability of a wing-fuselage configuration at subcritical Mach numbers. The method applies to unswept- and swept-wing configurations. The stability parameters estimated by the method show reasonable agreement with the experimental values for the 23 configurations used in the comparison.

The stator-blade angles in the twelfth to fifteenth stages of a 16-stage high-pressure-ratio axial-flow compressor were decreased 3 deg The over-all performance of this compressor is compared with the performance of the same compressor with standard blade angles. The matching characteristics of the modified compressor and a two-stage turbine were also obtained and compared with those of the compressor with the original blade angles and the same turbine.

Memorandum presenting an investigation to determine the increase in the useful ranges of flight conditions that may be obtained with a given jet-engine research facility when the choked nozzle technique or the exhaust jet diffuser, or both, are employed. The report describes the two methods, the considerations involved in their application, and typical results of their use as well as confirmation of the accuracy of data obtained by utilization of these techniques.

"The experimental performance of a modified turbine for driving a supersonic compressor is presented and compared with the performance of the original configuration to illustrate the effect of small changes in the ratio of nozzle-throat area to rotor-throat area. Performance is based on the performance of turbines designed to operate with both blade rows close to choking. On the basis of the results of this investigation, the ratio of areas is concluded to become especially critical in the design of turbines such as those designed to drive high-speed, high-specific weight-flow compressors where the turbine nozzles and rotor are both very close to choking" (p. 1).

A summary of some effective aerodynamic twisting-moment coefficients of various wing-control configurations for use at a range of Mach numbers. The values obtained were determined by the combined use of experimentally determined free-flight data and subsonic aerodynamic theory.

Report presenting testing of JP-3 fuel and a slurry of 60 percent powdered magnesium in JP-3 fuel in a small-scale afterburner in the presence of large quantities of water vapor. The results indicated that total temperature, combustion efficiency, and air specific impulse were improved when the magnesium slurry was used, but the improvements came at the cost of increased liquid consumption.

Memorandum presenting flutter tests of untapered, low-aspect-ratio, sweptback-wing models and of triangular-wing models of solid magnesium, aluminum, and steel construction in an intermittent supersonic wind tunnel at Mach number 1.3. Flutter data are presented for 31 sweptback wing models and 24 triangular-wing models. The flutter boundaries are indicated on plots of streamwise thickness ratio and aspect ratio.

Memorandum presenting an investigation of a 2:1 area ratio conical diffuser of length equal to the inlet diameter with separate variation of several basic parameters for simple nontwisted counterrotating rectangular vortex generators over a considerable range of inlet-boundary-layer thickness. The maximum values of static-pressure rise were determined for angle of attack, spacing, aspect ratio, and span-to-inlet boundary-layer thickness. Results for the diffuser with no vortex generators, effects of selectable vortex-generator variables, effect of inlet-boundary-layer displacement thickness, and use of the maximum indicated vortex-generator design values are provided.