Memorandum presenting measurements of some of the high-speed characteristics of the D-558-1 airplane up to Mach number 0.89. The results of the tests showed that the stabilizer incidence drastically affected the longitudinal trim characteristics above a Mach number of 0.80.

Memorandum describing a way in which the data of three previous reports can be used to compute the incompressible flow fields for cowling-spinner combinations and open-nose inlets for use in the design of propeller shanks and cuffs. The method consists of regarding the cowling surface as replaced by a ring vortex sheet whose strength at any point is equal to the local tangential velocity.

Report presenting the results of an investigation of flap-type controls on a low-aspect-ratio triangular wing using NACA 0005-63 sections for a constant-chord and a constant-percent-chord control surface. Two flap profiles were investigated: one with a true contour and the other with a blunt trailing edge. Results regarding lift, drag, pitching moment, hinge moment, and rolling moments were obtained for several Mach numbers, a constant Reynolds number, and a range of angles of attack.

Report presenting the results of an investigation of the static longitudinal stability and control characteristics of a canard airplane configuration without analysis for a range of Mach numbers. Data are presented for a variety of angles of attack and canard angles.

Report presenting a blade-vibration and rotating-stall survey on a modified version of a production turbojet engine with a 13-stage axial-flow compressor with a design pressure ratio of 7 and an air flow of 120 pounds per second. This testing was carried out due to the problems rotating stall can cause with both experimental and production axial-flow compressors. Results regarding the rotating-stall patterns, rotor-blade vibrations, radial and axial strength of rotating stall, and maximum rotating-stall speed are provided.

Report presenting an investigation in the 4- by 4-foot supersonic pressure tunnel to determine the effects of body contouring as specified by the transonic drag-rise area rule on the aerodynamic characteristics of a delta wing-body combination at Mach numbers of 1.41 and 2.01. Body contouring reduced zero-lift drag of a delta wing-body combination from that of a basic wing-body combination without contouring by 18 percent at Mach number 1.41 and 6 percent at Mach number 2.01. Results regarding the characteristics at zero lift and characteristics for the lifting condition are provided.

Report presenting free-flight investigations conducted on four 16-inch-diameter ramjet units to determine the performance at high subsonic and supersonic velocities. Data for evaluating the performance were obtained from radio-telemetering and radar-tracking equipment. Results regarding combustion performance, diffuser total-pressure recovery, thrust coefficient, and external drag coefficient are provided.

Tests were performed in the Langley Unitary Plan wind tunnel to determine the drag and static longitudinal and lateral stability and control characteristics of a 1/20-scale model of the McDonnell F4H-1 airplane at Mach numbers of 1 57, 1 87, 2.16, and 2.53. This is the second phase in a series of tests performed on this model. The Reynolds numbers for these tests, based on the mean aerodynamic chord of the wing, are 1.446 x 10 (exp 6), 1.269 x 10 (exp 6), 1.116 x 10 (exp 6), and 0.714 x 10 (exp 6) at Mach numbers of 1.57, 1.87, 2.16, and 2.53, respectively.

Report presenting an investigation with a ram-jet combustion chamber to determine the effect of fuel-air ratio and the inlet-air parameters of pressure, temperature, and velocity on combustion limit, combustion efficiency, and flame length.

From Summary: "Measurements of wing and fuselage pressure distributions were made at low and high subsonic Much numbers on a 0.16-scale model of the projected MX-656 research airplane. The MX-656 is a supersonic design utilizing a low-aspect-ratio wing and tail. Pressure-distribution measurements indicated that, although the critical Mach number of the wing was approximately 0.81 at 0 degree angle of attack, compressibility effects were of little significance below a Mach number of at least 0.90. The principal effect of compressibility was an increase in the pressure gradient over the after 30 percent of the wing chord, causing a tendency for the flow to separate."

Report presenting measurements of wing and fuselage pressure distributions made at low and high subsonic Mach numbers on a scale model of the projected X-3 research airplane. Tests were conducted in pitch and yaw and included measurements of the total pressure in the fuselage boundary layer at the location of the left boundary-layer bleed scoop.

The effects of fineness ratio (14.2 and 12.2) and boattailing on aerodynamic characteristics of four bodies of revolution at Mach numbers from 1.50 to 1.99 within a range of angles of attack from 0 degrees 10 degrees at an approximate Reynolds number of 35x10(superscript)6 based on body length were investigated. A comparison of experimental data with available theory is included. At zero angle of attack, fineness ratio has no appreciable effect on model characteristics while boattailing and boattail convergence significantly affect fore drag and base drag.

From Summary :"An investigation was conducted with a single combustor from a J47 turbojet engine using weathered aviation gasoline and several spark-plug modifications to determine altitude ignition, acceleration, and steady state operating characteristics. Satisfactory ignition was obtained with two modifications of the original opposite-polarity spark plug up to and including an altitude of 40,003 feet at conditions simulating equilibrium windmilling of the engine at a flight speed of 400 miles per hour. At a simulated altitude of 30,000 feet, satisfactory ignition was obtained over a range of simulated engine speeds."

"An investigation was conducted to determine the effectiveness of area suction used to delay the separation of air flow at the leading edge of a 63 degree swept-back wing. Changes in lift, drag, and pitching-moment data were correlated with the occurrence of the separation of the air flow by means of pressure-distribution data. It was found that the spanwise and the chordwise extent of area suction required to control leading-edge separation were in general agreement with that predicted by theory, but the quantity of flow required was considerably higher than predicted by theory" (p. 1).

"An investigation of the XJ-41-V turbojet-engine compressor was conducted to determine the performance of the compressor and to obtain fundamental information on the aerodynamic problems associated with large centrifugal-type compressors. The results of the research conducted on the original compressor indicated the compressor would not meet the desired engine-design air-flow requirements because of an air-flow restriction in the vaned collector. The compressor air-flow choking point occurred near the entrance to the vaned-collector passage and was instigated by a poor mass-flow distribution at the vane entrance and from relatively large negative angles of attack of the air stream along the entrance edges of the vanes at the outer passage wall and large positive angles of attack at the inner passage wall" (p. 1).

From Summary: "An investigation is being conducted to determine the performance of the 12-stage axial-flow compressor of the XT-46 turbine-propeller engine. This compressor was designed to produce a pressure ratio of 9 at an adiabatic efficiency of 0.86. The design pressure ratios per stage were considerably greater than any employed in current aircraft gas-turbine engines using this type of compressor. The compressor performance was evaluated at two stations."

Report presenting an investigation at Mach number 1.61 to determine the hinge-moment characteristics of seven tip controls on a 60 degree sweptback delta wing. Testing occurred over a range of angles of attack and control deflection. The results indicated that the most important parameter in designing delta-wing tip control is the ratio of control-surface area ahead of the hinge line to total control-surface area.

Report presenting testing of a twin-scoop duct inlet that enclosed 37.2 percent of the forebody circumference at Mach numbers between 1.36 and 2.01. The approach to each scoop consisted of a ramp that deflected the flow to create an oblique shock wave in front of the duct entrance. Results regarding the inlet proportions, ramp angle, slots, and angle of incidence are provided.

Report presenting pressure-drag coefficients and the changes in these coefficients with mass-flow ratio, which have been measured in tests of six open-nose conical cowls at an angle of attack of 0 degrees. Testing occurred in the Ames 8 by 8-inch supersonic wind tunnel at a range of Mach numbers. Results regarding pressure distributions, change in cowl pressure drag with mass-flow ratio, cowl pressure drag at a given mass-flow ratio, and changes in cowl pressure drag with mass-flow ratio as a function of Mach number are provided.

Report presenting the results of an investigation to determine the pressure ratios required to operate a slotted tunnel through a range of Mach numbers where the speed variation is affected by removal of air from the main stream by auxiliary pumping, use of a main-stream-operated ejector located downstream of the test section, and a combination of these methods. Testing was conducted in order to improve the accuracy of transonic wind-tunnel testing.

Report presenting a flight and preflight evaluation of an automatic thrust-coefficient control system in a twin-engine ram-jet missile. A flicker-type single-loop servocontrol system is shown to be a usable way of controlling ram-jet thrust coefficients.

Report presenting a flight test of pentaborane fuel in an air-launched ramjet engine with a design free-stream Mach number of 1.8. The ramjet used in the investigation had a revised spray bar-flameholder configuration. Results regarding propulsive thrust and propulsive-thrust specific fuel consumption are provided.

Flight investigation of pentaborane fuel in 9.75- inch-diameter ramjet engine with downstream fuel injection.

Memorandum presenting the results of a wind-tunnel investigation of the low-speed characteristics of horizontal tails of aspect ratio 3 with unswept and swept-back plan forms. Two models were tested which had identical areas, aspect ratio, taper ratio, and airfoil section, differing only in the angle of sweepback and elevator area ratios. The major effect of sweepback was to increase the rate of change of hinge-moment coefficient with angle of attack, to reduce the rate of change with elevator deflection, and to reduce the elevator effectiveness.