From Introduction: "In the present report, the results for the wings and bodies of revolution alone are first analyzed in comparison with exiting theory."

Memorandum presenting several top-inlet configurations tested on a body of revolution in the 8- by 6-foot supersonic wind tunnel at a range of angles of attack and free-stream Mach numbers. The effect on performance of the following variables were studied: throat bleed, ramp perforations, inlet approach surface, side fairings, fuselage fences, canopies, and a simulated 60 degree delta wing.

Report presenting an investigation to determine the control characteristics of flap-type controls of various chords and spans on an unswept wing with a modified double-wedge section, an aspect ratio of 2.5, and a taper ratio of 0.625.The control chords in the study were 25, 35, and 45 percent of the wing chord, and the control spans were 25, 50, and 75 percent of the wing semispan. The data from the study indicated that the control-parameter values are approximately proportional to control chord or span for the chords tested.

Report presenting an investigation of a turbojet engine with variable inlet guide vanes in an altitude test facility to determine the steady-state compressor performance and surge characteristics. Compressor surge pressure ratios were found to be unaffected by changes in flight condition for either position of the inlet guide vanes. Decreasing the inlet Reynolds number was found to reduce the corrected fuel flow required for compressor surge.

Report presenting a large-scale diamond-wing-body configuration flown at a range of Mach and Reynolds numbers. The model had a diamond-plan-form wing with an NACA 65A003 airfoil section, a total aspect ratio of 2.31, and 0 degrees sweep of the midchord. Results regarding zero-lift drag and low-lift longitudinal characteristics are provided.

Memorandum presenting experimental flutter Mach numbers for several solid, thin, rectangular cantilever wings with uniform section properties, low aspect ratio, and high relative density estimated from the results of previous tests at zero angle of attack. The experimental values are considered estimates, rather than determinations, in the high subsonic speed range because in that range the amplitude criterion was necessarily arbitrary. Results regarding conservatism of standard analysis relative to the experiment, closeness of analytical and experimental results, and interpretation of the analytical and experimental uncertainties are provided.

From Introduction: "The investigation reported herein was initiated to define further the effects on the aerodynamic characteristics and load distribution of a thin, sweptback wing of a low-pressure blowing system and also to provide information on which to base a more thorough study of a complete airplane configuration."

From Introduction: "The purpose of this paper is to discuss and evaluate some of the input signals or control parameters which have been experimentally employed to operate turbojet inlet-control systems. These include the normal-shock position, the oblique-shock position, and the diffuser-exit Mach number. The discussion is based on results obtained at the NACA Lewis laboratory during control investigations of ram-jet engines (ref. 1 to 5) and during a study on the control of a supersonic inlet for the J34 turbojet engine (refs 6 and 7)."

Report presenting preliminary tests of a counterrotating axial-flow supersonic compressor, which indicates that a flow limitation in the second rotor restricted the flow rate at design speed. The second-stage rotor was modified by increasing the flow area to increase the flow rate and improve flow stability. Results regarding the overall performance of the modified compressor, radial variation of flow conditions and performance parameters in the second rotor, stability of the shock wave in the second rotor, and individual stage performance are provided.

Report presenting flight measurements of the lateral control characteristics of the Douglas D-558-II airplane in abrupt rudder-fixed aileron rolls. Results regarding the aileron rolling effectiveness, time histories, and aileron effectiveness variation with Mach number are provided.

Memorandum presenting an investigation of the effects of orientation by multi-axial stretching on properties of various plastic glazing materials. The materials studied were Lucite HC-222, Plexiglass 55, Gafite, and resin C. Some of the tests conducted included dimensional stability at elevated temperatures, surface abrasion, standard tensile tests, and stress-solvent crazing tests using ethylene dichloride.

Report presenting an investigation of the low-speed characteristics of a wing swept back 42 degrees at the leading edge and having various high-lift and stall-control devices and fuselage and horizontal tail vertical positions. Results regarding the characteristics of the basic wing, leading-edge flap investigation, wing fuselage investigation, and horizontal tail investigation are provided.

Memorandum presenting a review of the current and anticipated lubricant problems as related to aircraft turbojet engines, which has indicated that the current and anticipated bearing operating temperature ranges to be met are specified. The most promising approaches, including types of lubricants and temperatures, are provided.