The report comprises seven sections. A separate abstract was prepared for each section. (J.R.D.)

Tests of Cambridge absolute filters, Model Sl-071, specified for use in the GCR-ORR Loop No. 2 as full-flow, primary coolant fiiters were completed. kD.O.P/ (dioctylphthalate) efficiency tests were performed on three filters in the as-received condition, on two filters following canning and thermal cycling, and on one of the canned fiIters following bsking out. None of the three units met the design criteria of 99.97% efficiency for removal of 0.3 micron particles in the as-received condition. The postthermal cycle efficiencies of the canned fiIters were slightly higher than their respective as-received efficiencies. At the corapletion of testing, the two fiiters canned for installation in the reactor facility had measured efficiencies of 99.855% and 99.93%. These values were judged acceptable for the intended application/su The thermal cycling of the two canned filters and the subsequent baking out of one of these units demonstrated that a limited amount of off-gas products would be given off/su Pressure drop tests were performed on the canned fiiters with instrument air (ambient temperature, atmospheric pressure) over a flow rate range of 150 to 530 lb/hr. Curves of pressure drop across each fiIter versus Reynolds number were plotted for air and He. (auth)

In the tandem mirror experiment (TMX), coherent oscillations have been identified as resulting from the Alfven ion-cyclotron instability. Although the drive for this instability is localized in the end cell, the waves generated propagate out of the unstable region and interact with the central-cell ions. This interaction leads to an experimentally observed scaling of the stored end-cell energy with axial ion end-loss current.

Two automated reaction calorimetry systems were built and tested. The first made use of a quartz thermometer probe as the temperature measuring element. The second was constructed using a thermister which was part of a Wheatstone bridge. The off-balance voltage from the bridge was measured using the 6 1/2 digit digital voltmeter, and transferred to the microprocessor. The one disadvantage of the first system is the relatively large size of the quartz sensor. The calorimeter systems were used to measure: the enthalpies of hydrolysis of ketals, acetal, orthoesters, enthalpies of hydration of alkenes; enthalpies of formation of small ring hydrocarbons. (ATT)

The maximum stress calculated for the SMl-1 reactor vessel closure studs occurs during operation at full power. This value is 27,180 psi of which 19,800 psi is tension and 7380 psi bending. This stress does not include a stress concentration factor for effect of threads. It was eonservatively assumed the studs were initially tightened to a code allowable stress of 20,000 psi as specified in the ASME Code rather than the lesser stress obtained by the normal operating procedure. The maximum calculated stress occurs at the outside surface of the cover where the stress ranges from 318 psi in tension to 90,660 psi in compression. The alternating stress is 50,000 psi. According to the Navy Code for a stress range of 50,000 psi, the eover material ean safely undergo a maximum of 1600 cycles. It was estimated that the SM-1 will go through approximately 000 startup and shutdown cycles during a 20-yr life period, so the calculated stress is regarded as safe. For a transient eondition of 30 deg F/hr during heat-up, approximate temperature differences between the inside and outside surfaces of the cover were obtained. Temperature differentials between the inside and outside surfaces of the cover are increased by …

Astrophysical r-process calculations of transbismuth elements are of interest because certain actinide pairs can be treated as chronometers in determining the duration of nucleosynthesis. For one such calculation where a particularly long galactic age was derived, 21 + 2 - 4 Gyr, we present evidence that the effect of beta-delayed fission appears to be seriously overestimated in uranium decay chains with A = 252 to 257. With this conclusion, it follows that this estimate of the galactic age must be considered more uncertain than if the calculated rates of beta-delayed fission were found to be acceptable. The nuclear level structure of 238Np has been investigated using the 237Np(n,..gamma..)238Np reaction and the alpha decay of 242mAm as experimental probes. Having established a level scheme for 238Np that includes 47 excited levels and 93 secondary transitions, we find a high degree of correspondence between the experimental band structure and that of a semi-empirical model developed to predict excitations in odd-odd deformed nuclei. 35 refs., 4 figs., 3 tabs.

Twenty-seven papers are presented on beryllium supply, production, fabrication, safe handling, analysis, powder technology, and coatings. Separate abstracts have been prepared for the individual papers. (DLC)

At the Lawrence Livermore Laboratory, a computer code based on the Gaussian plume model is used to estimate radiation doses from routine or accidental release of airborne radioactive material. Routine releases of tritium have been used as a test of the overall uncertainty associated with these estimates. The ration of concentration to release rate at distances from the two principal release points to each of six site boundary sampling locations has been calcuated using local meteorological data. The concentration of airborne tritiated water vapor is continuously measured at the six sampling stations as part of the Laboratory's environmental monitoring program. Comparison of predicted with observed annual tritiated water concentrations in 1978 showed an average ratio of 2.6 with a range of from 0.97 to 5.8.

This report describes efforts leading to the development and characterization of a compact ion source and optical transfer system producing relatively high current density ion beams. The ion source and beam transfer system represent a major advance in the state of the art in that high current densities at low kinetic energies have been achieved for high molecular weight polyatomic ions. Indeed, the ion beams produced display ion abundance patterns typical of simple low energy electron impact ionization processes.

FIRESET is a PC-based computer code which calculates current as a function of time for an RLC circuit containing up to fifteen series conductors which undergo rapid heating and subsequent explosion as a consequence of an electric current which passes through them. In its original form, the code was developed to model electrical waveforms measured when a large, typically 25.4 x 25.4 x 0.051-mm, aluminum foil was exploded using a capacitor bank with tens of kilojoules of stored energy. The code proved to be useful for this purpose, and it was recognized that it could also be used for modeling the electrical response of detonator bridgewires. In view of the increasing use of slapper detonators for DOD applications, we wish to make the latest version of the code, available to DOD laboratories and contractors for use in designing firing systems which employ slapper or exploding bridgewire detonators. This document provides instructions for the code.

The objective of this contract is to extend and optimize UOP's single-stage, slurry-catalyzed co-processing scheme. The particular emphasis is one evaluating alternative and disposable slurry-catalyst systems. During the current quarter, Lloydminster vacuum resid was processed without the presence of coal. The objective of this study was to evaluate the manner in which the resid is upgraded at high-severity conditions to help understand the function of the resid during co-processing. This report coves Bench-Scale Runs 30 to 34. In Runs 30 to 34, Lloydminster vacuum resid was processed without the presence of coal using a 0.05 wt % molybdenum-based catalyst at 465{degrees}C.

A survey of the literature on carbonate scaling is presented as it affects geothermal fluid systems. The geothermal brine, as the fluid is called, contains a number of chemical constituents which have leached into it from the reservoir rock. As the hot fluid is withdrawn through wells, a flow of steam, water, or a mixture of steam and water, results. If the well flows at a high enough rate, some brine will flash to steam because of the pressure drop, resulting in the steam/water flow mixture. The chemical composition of the brines is tabulated as the composition of the components in the water system before flashing and the composition of the non-condensible gases after flashing. Total dissolved solids vary from that of ordinary well water to concentrated solutions as high as 40% by weight. Calcium is a major cationic constituent, and biocarbonate an important anionic constituent of the brine. Prevention/treatment techniques, specific site experimental results, and computer models are presented.

This current project is pilot-scale testing of NO{sub x} recycle. The objective is to provide further fundamental understanding and useful information for its implementation at the Niles station. A Babcock Wilcox's 6 million Btu/hr Small Boiler Simulator (SBS) has been chosen to perform the tests. The SBS is the same type of cyclone furnace as that at Niles and simulates a large cyclone unit very well. The project involves conducting a series of tests which include injecting NO, NO{sub 2}, N{sub 2}O, and simulated NO{sub x} recycle stream respectively. The work performed during this reporting period focused on the site preparation, shakedown tests, and baseline tests. The shakedown testing of NO injection into the primary air stream alone and the secondary air stream alone showed promising results. A large amount of NO injected into furnace was destroyed, especially when the NO was injected into the primary air duct. However, the measuring instrumentation needs to be improved to give accurate data.

None

We present measurements of elliptic flow and event-by-event fluctuations established by the PHOBOS experiment. Elliptic flow scaled by participant eccentricity is found to be similar for both systems when collisions with the same number of participants or the same particle area density are compared. The agreement of elliptic flow between Au+Au and Cu+Cu collisions provides evidence that the matter is created in the initial stage of relativistic heavy ion collisions with transverse granularity similar to that of the participant nucleons. The event-by-event fluctuation results reveal that the initial collision geometry is translated into the final state azimuthal particle distribution, leading to an event-by-event proportionality between the observed elliptic flow and initial eccentricity.

U.S. Department of Energy (DOE) Order 450.1, Environmental Protection Program, requires each DOE site to conduct environmental monitoring. Environmental monitoring at the Waste Isolation Pilot Plant (WIPP) is conducted in order to: (a) Verify and support compliance with applicable federal, state, and local environmental laws, regulations, permits, and orders; (b) Establish baselines and characterize trends in the physical, chemical, and biological condition of effluent and environmental media; (c) Identify potential environmental problems and evaluate the need for remedial actions or measures to mitigate the problem; (d) Detect, characterize, and report unplanned releases; (e) Evaluate the effectiveness of effluent treatment and control, and pollution abatement programs; and (f) Determine compliance with commitments made in environmental impact statements, environmental assessments, safety analysis reports, or other official DOE documents. This Environmental Monitoring Plan (EMP) has been written to contain the rationale and design criteria for the monitoring program, extent and frequency of monitoring and measurements, procedures for laboratory analyses, quality assurance (QA) requirements, program implementation procedures, and direction for the preparation and disposition of reports. Changes to the environmental monitoring program may be necessary to allow the use of advanced technology and new data collection techniques. This EMP will document any proposed changes …

A total of 66 urine samples, 6 blank fecal and 6 spiked artificial fecal samples were submitted during the report period (April 1, 2006 through March 31, 2007) to General Engineering Laboratories, South Carolina by the Hanford Internal Dosimetry Program (IDP) to check the accuracy, precision, and detection levels of their analyses. Urine analyses for tritium, Sr, 238Pu, 239Pu, 241Am, 243Am 235U, 238U, elemental uranium and fecal analyses for 241Am, 238Pu and 239Pu were tested this year. The number of QC urine samples submitted during the report period represented 1.7% of the total samples submitted. In addition to the samples provided by IDP, GEL was also required to conduct their own QC program, and submit the results of analyses to IDP. About 36% of the analyses processed by GEL during the second year of this contract were quality control samples. GEL tested the performance of 16 radioisotopes, all of which met or exceeded the specifications in the Statement of Work. IDP concluded that GEL was performing well for all analyses tested, and concerns identified earlier were satisfactorily resolved.

The overall objective of this program is to develop the engine and lubricant system design approach that has the highest probability for commercial acceptance. Several specific objectives can also be identified. These objectives include: definition of the dominant wear mechanisms prevailing in coal-fueled diesel engines; definition of the specific effect of each coal-related lube oil contaminant; determination of the potential of traditional engine lubrication design approaches to either solve or mitigate the effects of the coal related lube oil contaminants; evaluation of several different design approaches aimed specifically at preventing lube oil contamination or preventing damage due to lube oil contamination; and presentation of the engine/lubricant system design determined to have the most potential. 2 figs., 3 tabs.

The role of weak interactions, particularly electron capture and {beta}{sup {minus}} decay, in presupernova evolution is discussed. The present uncertainty in these rates is examined and the possibility of improving the situation is addressed. 12 refs., 4 figs.

A simple, compact, high brightness x-ray source has recently been built. This source utilizes a commercially available, cylindrical geometry electron beam evaporator, which has been modified to enhance the thermal cooling to the anode. Cooling is accomplished by using standard, low-conductivity laboratory water, with an inlet pressure of less than 50 psi, and a flow rate of approx.0.3 gal/min. The anode is an inverted cone geometry for efficient cooling. The x-ray source has a measured sub-millimeter spot size (FWHM). The anode has been operated at 1 KW e-beam power (10 KV, 100 ma). Higher operating levels will be investigated. A variety of different x-ray lines can be obtained by the simple interchange of anodes of different materials. Typical anodes are made from easily machined metals, or materials which are vacuum deposited onto a copper anode. Typically, a few microns of material is sufficient to stop 10 KV electrons without significantly decreasing the thermal conductivity through the anode. The small size and high brightness of this source make it useful for step and repeat exposures over several square centimeter areas, especially in a research laboratory environment. For an aluminum anode, the estimated Al-K x-ray flux at 10 cms from the source …

This project is a part of the continuing Smolt Monitoring Program (SMP) to monitor Columbia Basin salmonid stocks coordinated by the Fish Passage Center (FPC). The SMP provides timely data to the Fish Passage Managers for in season flow and spill management for fish passage and post-season analysis by the FPC for travel time, relative magnitude and timing of the smolt migration. Sampling sites were McNary, John Day and Bonneville Dams under the SMP, and the Dalles Dam under the Fish Spill Memorandum of Agreement'' for 1989. All pertinent fish capture, condition and brand data, as well as dam operations and river flow data were incorporated into the FPC Fish Passage Data Information System (FPDIS). 15 refs., 6 figs., 6 tabs.

The central research problem of this project is the effective representation, computation, and display of surfaces interpolating to information in three or more dimensions. If the given information is located on another surface, then the problem is to construct a surface defined on a surface''. Sometimes properties of an already defined surface are desired, which is geometry processing''. Visualization of multivariate surfaces is possible by means of contouring higher dimensional surfaces. These problems and more are discussed below. The broad sweep from constructive mathematics through computational algorithms to computer graphics illustrations is utilized in this research. The breadth and depth of this research activity makes this research project unique.

The objective of this contract is to extend and optimize UOP's single-stage, slurry-catalyzed co-processing scheme. The current task is to complete a long-term operability run using a 0.05 wt-% Mo-based catalyst at approximately 460{degrees}C. The objectives of this run are to demonstrate that high-severity conditions can be run for an extended period of time (at least one month) and to collect enough product sample to do a complete Hempel fractionation and detailed characterization of the individual naphtha, distillate, and VGO cuts. This information will be used to reevaluate the engineering design and product upgrading scheme that was developed under the first co-processing contract (DE-AC22-84PC70002). During the current two quarters, the long-term operability study was unsuccessfully attempted several times. This report discusses these attempts.

A digitally based deflection generator for an electron-beam welder is presented. Up to seven patterns of any shape are stored in programmable read-only memory (PROM). The pattern resolution is 39% at frequencies from 10 Hz to 1 kHz and can be x-t, y-t, or x-y formed. Frequency and pattern selections may be chosen by the welder computer or manually selected on the front panel. The ability to repeatedly synchronize two waveforms of any shape and frequency enables an unlimited variety of welds.