Report presenting an investigation of a fin-stabilized scale model of the NACA RM-10 missile at a Mach number of 1.62. Measurements were made of the lift, drag, and pitching moment of the finned body over a range of angles of attack. Comparisons with the results from other testing facilities are also provided.

Report presenting an investigation of an NACA 1-80-100 nose inlet fitted alternately with an elliptical, a parabolic, a 14 degree-inch conical, and a 22 degree-inch conical central body at subsonic and transonic speeds in the 8-foot transonic tunnel. Drag, surface-pressure, and pressure-recovery measurements were obtained at 0 degrees angle of attack through a range of Mach numbers. Results regarding tunnel boundary interference, surface-pressure distribution, external drag, pressure recovery, and propulsive thrust comparison are provided.

From Introduction: "The objective of this report are (1) to describe the complete fuel system, (2) to discuss the procedure used for transitions between JP-4 fuel and hydrogen, and (3) to present and discuss engine performance obtained with both fuels, and (4) to review the reliability of the fuel system."

Report presenting an investigation of a liquid-hydrogen fuel system developed to operate one of the turbojet engines in a twin-engine light bomber at an altitude of 50,000 feet and Mach number 0.75. The heat exchanger was evaluated in an altitude test chamber in conjunction with the complete aircraft fuel system. Results regarding calculated heat-exchanger performance, experimental heat-exchanger performance, and reliability are provided.

Memorandum presenting the system analysis, design, and performance of a control system for an experimental flight-type hydrogen fuel system. The fuel system was designed to investigate some of the problems associated with the utilization of hydrogen as an aircraft fuel. Speed control of the engine was obtained by coupling the hydrogen regulator to the JP-4 fuel control.

Memorandum presenting testing of a twin-engine light bomber modified to utilize hydrogen fuel in one of the two engines during flight at an altitude of 50,000 feet. Three completely successful flights were made using hydrogen fuel. Data are presented to show the effect of tank agitation on fuel pressure and fuel losses.

From Introduction: "The purpose of this paper is to present and discuss skin temperature measurements from two flight tests. Temperature measurements were obtained to a Mach number of 5.4 on the first flight and to a Mach number of 10.4 on the second flight."

Report presenting fluid-dynamics studies of a tank of fineness ratio 7.0 which was pylon mounted on a simplified two-dimensional flutter model in order to determine the effects of the fluid on flutter. The flutter speed was determined for three cases: with various amounts of water in the tank, with weights with the same mass and moment of inertia as the fluid considered to be a frozen solid, and with weights with the same mass and moment of inertia as the actual fluid. Results regarding the flutter speed, effects of inertia on flutter, and amplitude of flutter are provided.

An investigation of the performance and operating characteristics of two variable-thrust injectors over a wide thrust range using mixed oxides of nitrogen and ammonia. Specific impulse, characteristic velocity, thrust coefficient, and overall efficiency are presented as functions of thrust. A maximum thrust range of 12 during one run was obtained with a triplet impinging-jet injector.

From Summary: "The procedure currently employed by the NACA Lewis Laboratory in the design of transpiration-cooled strut-supported turbine rotor blades is discussed. The strut is the internal blade supporting member and also serves to partition the blade into separate cooling-air passages. Orifices in the blade base, which meter the cooling-air to each internal passage, are used in conjunction with a constant chordwise permeability."

Inserting a splitter plate in the subsonic diffuser caused a pressure-recovery loss of about 1 percent for an inlet with a long nearly constant-area throat section. The loss was due to the increased surface area. Another inlet, which had a comparatively rapid area increase immediately after the throat, experienced pressure-recovery losses of 5 and 6 percent at Mach numbers of 1.8 and 2.0, respectively, and about 1 percent at Mach 1.5.

Engine performance is better for constant outer-spool mechanical-speed operation than for constant inner-spool mechanical-speed operation over most of the flight range considered. Combustor and afterburner frontal areas are about the same for the two modes. Engine performance for a mode characterized by a constant outer-spool equivalent speed over part of the flight range and a constant outer-spool mechanical speed over the rest of the flight range is better that that for constant outer-spool mechanical speed operation.

Report presenting a comparison of the buffet loads measured on wind-tunnel models with loads measured in flight, which indicate that a simple strain-gage measurement can be used in wind tunnel testing that can be used to predict the wing buffet loads on the airplane. The technique appears to be usable for both unswept and swept configurations.

Report presenting an experimental investigation to study several wing-root inlet configurations at Mach number 1.9. The inlets were of triangular and rectangular shape and external compression was provided by two-dimensional wedge surfaces. Results regarding the pressure-recovery and mass-flow data, effect of inlet side plates and curved diffusers, exit and inlet total-pressure distributions, improvement of exit total-pressure profiles, and inlet tests at zero flight speed are provided.

Report presenting an investigation at the Lewis laboratory to develop air-cooled, strut-supported turbine blades. Six blades were investigated in a full-scale turbojet engine to obtain data on blade durability and blade-cooling effectiveness and strut temperature. Results regarding the heat-transfer investigation and blade-durability investigation are provided.

Report presenting the steady-state performance of the YJ73-GE-3 turbojet engine in an altitude test chamber for a range of exhaust-nozzle areas, simulated altitudes, and Mach numbers. A method of performance calculation based on engine pumping characteristics is provided. Results regarding performance maps, pumping characteristics and performance prediction, thrust correlation, effect of inlet temperature on performance, calculated performance from pumping characteristics, and altitude-ignition characteristics are provided.

Memorandum presenting an aerodynamic design-point analysis of one-spool turbojet engines with one-stage turbines with one and with two rows of downstream stator blades. The object of the analysis was to evaluate the design characteristics of the turbines in comparison with conventional one- and two-stage turbines, to determine the extent to which exit whirl can be increased before causing weight-flow capacity to decrease, and to determine the effect of downstream stators on engine design limitations.

Memorandum presenting an analysis to indicate the feasibility of the supercritical water compressor jet cycle for nuclear powered aircraft. Performance values of the cycle are given for a range of design-point engine operating conditions and subsonic flight conditions.

Memorandum presenting an experimental study of the effects of several variations in configuration geometry on the aerodynamic characteristics of flat-top wing-body combinations. Generally, the configurations consist of one half of a body of revolution mounted beneath a wing of essentially arrow plan form. Results regarding the effect of trailing-edge sweep, effect of the addition of auxiliary bodies, effect of tip-flap deflection, effect of dihedral, effect of leading-edge sweep, effect of fuselage fineness ratio, effect of fuselage profile shape, and static longitudinal stability characteristics are provided.

Memorandum presenting an investigation to determine the roll effectiveness of a differentially deflected horizontal tail of a 42 degree swept-wing model. The model was tested through an angle-of-attack range of 0 degrees through the stall in the clean and landing configurations with the horizontal tail in a low position. Results regarding the longitudinal characteristics and lateral characteristics are provided.

Report presenting an investigation of the thermal-shock effect of water-spray impingement upon turbine rotor blades subjected to rated engine operating conditions using external water-spray cooling. Turbine-blade cooling water was turned on and off in cycles which employed either sudden or gradual injection of cooling water. Results regarding blades modified and unmodified for rotating injection are provided.

"A tip section of a delta wing having an NACA 0004-65 airfoil section and a 600 leading-edge sweepback was equipped with a porous leading-edge section through which hot gas was bled for anti-icing. Heating rates for anti-icing were determined for a wide range of icing conditions. The effects of gas flow through the porous leading-edge section on airfoil pressure distribution and drag in dry air were investigated" (p. 1).

Report discussing the boundary-layer transition and heat-transfer measurements for a model of the Titan intercontinental ballistic missile up to a specified Mach and Reynolds number. Boundary-layer transition was observed on the nose of the missile. The drag coefficient for a variety of Mach numbers was also obtained.

Memorandum presenting an investigation to determine the energy transfer by thermal radiation from the flame of a single tubular turbojet-engine combustor to the combustor liner. The effects of variations in combustor inlet-air pressure, fuel-air ratio, and air mass flow on the transfer of radiant energy were studied.