The Lawrence Livermore Laboratory (LLL), as part of the Nevada Nuclear Waste Storage Investigations (NNWSI) program, is carrying out in situ rock mechanics testing in the Climax granitic stock at the Nevada Test Site (NTS). This summary addresses only those field data taken to date that address thermomechanical modeling for a hard-rock repository. The results to be discussed include thermal measurements in a heater test that was conducted from October 1977 through July 1978, and stress and displacement measurements made during and after excavation of the canister storage drift for the Spent Fuel Test (SFT) in the Climax granite. Associated laboratory and field measurements are summarized. The rock temperature for a given applied heat load at a point in time and space can be adequately modeled with simple analytic calculations involving superposition and integration of numerous point source solutions. The input, for locations beyond about a meter from the source, can be a constant thermal conductivity and diffusivity. The value of thermal conductivity required to match the field data is as much as 25% different from laboratory-measured values. Therefore, unless we come to understand the mechanisms for this difference, a simple in situ test will be required to obtain a …

None

The 5MW(e) electrical generating plant is a demonstrational unit intended to provide engineering data basic to improvement of geothermal-electric technology. It is anticipated that the plant will operate on a production basis after initial testing, and that periodic re-testing will be done to measure the effects of fouling in heat exchanges and aging generally. The initial tests will confirm engineering estimates of performance, and will identify optimum feasible operatinq conditions and maximum power generating capacity. They will also identify any anomalous plant behavior not foreseen. Several tests will lead to quantification of constant and variable terms used in thermodynamic relationships descriptive of plant and subsystem behavior. Because the product of the testing will be confirmatory engineering data heretofore unavailable, the plant has been carefully instrumented, with either explicit or implicit instrumentation redundancy for most parameters to be measured. The 5MW(e) data system collects the data directly from the instrumentation. Enhancements such as on-line analytical routines may be added later, but initially, data capture shall be the sole activity of the data system. The 5MW(e) plant converts the energy of geothermally heated water to electrical energy conforming to 60 Hz commercial power standards. The plant capacity is sufficiently large to be …

Possible geothermal development for the township of North Bonneville, Washington is being investigated because of the proximity of the town to hot springs in a geologic province of good geothermal potential. Surface expression of geothermal resources is provided by conduits through an impermeable reservoir cap and is therefore generally structurally controlled. Near North Bonneville the geologic formations that underlie potential drilling sites are the Eagle Creek formation and the Ohanpecosh Formation. The Lower Miocene Eagle Creek Formation is composed of poorly consolidated volcanic conglomerates, sandstones, tuffs, and includes a few minor interbedded lava flows. The Eocene-Oligiocene Ohanapecosh (Weigle) Formation in its nearest exposures to North Bonneville is composed of volcaniclastics and lava flows. The Ohanapecosh has been altered to zeolites and clays and is therefore well consolidated and impermeable. The lack of permeability provides the necessary reservoir cap for any geothermal system that may be present at depth. This formation, to the northeast, in the Wind River drainage is greater than 19,000 ft. thick. Circulation of geothermal heated water from this thick sequence of impermeable strata must be associated with penetrating fracture zones.

Objective is to design synthesize, and evaluate cyclic and polycyclic host organic compounds for their abilities to complex and lipophilize guest metal ions, their complexes, and their clusters. Host organic compounds consist of strategically placed solvating, coordinating, and ion-pairing sites tied together by covalent bonds through hydrocarbon units around cavities shaped to be occupied by guest metal ions or by metal ions plus their ligands. Specificity in complexation is sought by matching the following properties of host and guest: cavity and metal ion sizes; geometric arrangements of binding sites; number of binding sites; character of binding sites; and valences. During this period, hemispherands based on an aryloxy or cyclic urea unit, spherands based on aryloxyl units only, and their complexes with alkali metals and alkaline earths were investigated. An attempt to separate /sup 6/Li and /sup 7/Li by gel permeation chromatography of lithiospherium chloride failed. (DLC)

The development of standardized techniques for the comparative evaluation of electric vehicle battery technologies is summarized. The methodology considers both the traditional measures of battery performance (energy density, energy storage costs, and cycle life) and the equally important usage related battery characteristics (probability of technical success, operating and maintenance parameters, and safety/environmental impact). This comparative rationale is supplemented by the ability to generate battery test programs normalized to specific technologies and electric vehicle mission specifications. These test programs allow the evaluation of different battery technologies at comparable levels of electric vehicle performance. It was found that cost optimized electric passenger vehicles will have range specifications of 100 to 110 KM, depending on the specific performance of the battery. Longer range vehicles are penalized by higher first costs while shorter range vehicles suffer from reduced battery life and the need for more frequent alternative car rentals (presumably petroleum fueled) for trips which exceed the EV's range capability.

The Gravimelt Process was extended to the desulfurization of ordinary mine-cleaned Kentucky No. 11 coal obtained from the Tennessee Valley Authority. Eight process runs were made resulting in reduction of the sulfur content from a starting 2.7 lbs S/10/sup 6/ Btu to a mean of 0.475 lbs S/10/sup 6/ Btu, (0.95 lbs SO/sub 2//10/sup 6/ Btu) for an average 82% sulfur reduction. The effect of utilization of molten sodium hydroxide alone vs molten mixed potassium and sodium hydroxide was investigated for this coal; sulfur reduction averaged 84% for the mixed melt and 78% for the use of sodium hydroxide alone. A double extraction with sodium hydroxide resulted in a reduction in total sulfur to 0.3 lbs S/10/sup 6/ Btu which is an 89% reduction. In a series of experiments, the melt was reused three times on fresh samples of coal, always giving the same amount of sulfur reduction. Extraction of the desulfurized Kentucky No. 11 coals with an additional dilute sulfuric acid wash reduced the ash content of the coal from 7.9% to a level of 0.3%, thus providing a solid hydrocarbon fuel similar in both ash and sulfur content to a medium grade fuel oil. Multiple experimentation on high …

The toxicology and metabolism of nickel compounds (e.g., NiCl/sub 2/, ..cap alpha..Ni/sub 3/S/sub 2/, and Ni(CO)/sub 4/) were investigated in rats and hamsters.

Equipment modifications to a Freon 11 boil-off type calorimeter are described. The calorimetric system was used to measure the enthalpies of thiophene experimentally. Data were taken over a temperature range of 100/sup 0/F to 750/sup 0/F at pressures of 50, 100, 200, 400, 600, 825.9 (the critical), 1000, and 1500 psia. Thermodynamic properties derived from the data are compared to values in the literature, and the agreement is exceptionally good. The data are then compared directly to results calculated by means of two correlations: a modification of the BWR equation of state by Kesler and Lee, and a modified SRK equation of state method. Both correlations are found to work well in predicting the enthalpy of thiophene.

Extremely smooth, uniform metal coatings of micrometer thicknesses on microscopic glass spheres (microspheres) are often needed as targets for inertial confinement fusion (ICF) experiments. The first part of this paper reviews those methods used successfully to provide metal coated microspheres for ICF targets, including magnetron sputtering, electro- and electroless plating, and chemical vapor pyrolysis. The second part of this paper discusses some of the critical aspects of magnetron sputter coating of microspheres, including substrate requirements, the sticking of microspheres during coating (preventing a uniform coating), and the difficulties in growing the desired dense, smooth, uniform microstructure on continuously moving spherical substrates.

The objective of the BNL Neutral Beam Program is to develop a 250 keV neutral beam system suitable for heating experiments in toroidal or mirror plasma devices. The system will be based on acceleration and neutralization of negative hydrogen ions produced in and directly extracted from a source. The objective of source studies is to develop a unit delivering 10 A of negative ion currents in pulses of 1 s duration or longer, operating with extracted current densities of at least 0.5 A/cm/sup 2/ and having acceptable power and gas efficiencies and good beam optics. The 250 keV accelerator development work covers different structures, including those separated from the source by a bending magnet or a beam transfer system. During FY 1979 substantial progress was achieved toward the objectives of the program; in the same period the BNL program was reviewed by a panel, resulting in suggestions for a better orientation toward prospective users' requirements and in establishment of contacts with Princeton Plasma Physics Laboratory (TFTR Project) and Lawrence Berkeley and Livermore Laboratories (MFTF Project). A cooperative effort with Westinghouse was initiated in the second half of FY 1979 in order to utilize industrial facilities and expertise.

This will be an overview in which some of the general properties of loads are examined: their interface with the energy storage and switching devices; general problems encountered with different types of loads; how load behavior and fault modes can impact on the design of a power conditioning system (PCS).

In the preceding quarterly report, it was reported that while sampling the Solvent Refined Coal II (SRC II) pilot plant at Fort Lewis, Washington, the plant went down and vacuum bottoms waste material representing the minerals flow at the last steady state condition were obtained. This plant has been sampled again and samples of the incoming feed coal, sized coal and vacuum bottoms waste material were obtained. As part of our effort to trace the same mineral suite through mining, preparation and conversion, new samples of feed coal, cleaned coal and refuse were obtained from the District 4 commercial preparation plant. This preparation plant supplies coal to the SRC II pilot plant at Fort Lewis, Washington. A study of the thermal insulating properties of fired flyash based structural materials was completed and is included.

The Sunkist Citrus Plant in Ontario, California, processes about 6 million pounds of citrus fruit per day to make products which include frozen concentrated juice; chilled, pasteurized, natural strength juice; molasses from peel; dried meal from peel; pectin; citrus oil; and bioflavonoids. The energy intensive operations at the plant include concentration, drying, and refrigeration. The objective of the two-year two-phase project is to identify an economically viable alternative to the existing method of meeting energy requirements. Progress on the technical work of Phase I is reported. The following are summarized: requirements (energy price projection, atmospheric emission requirements, citrus juice quality constraints, economic evaluations); characterization (basic citrus processing operations, energy consumption and fruit processed vs time, identification and measurement of energy uses, energy balance for a typical citrus juice evaporator); and thermodynamic analysis (heat pump model, thermal evaporator, and co-generation model).

Thin film gold/polycrystalline cadmium telluride Schottky solar cells made by electrodepositing the semiconductor on an ITO-coated glass substrate serving also as an ohmic contact demonstrated an internal efficiency of 4% over 2 mm/sup 2/ areas. During the year being reported upon, Monosolar devoted mator attention to refining the electroplating process and determining the parameters governing CdTe film stoichiometry, grain size, substrate adhesion, and quality. UCLA acting as a Monosolar sub-contractor characterized both the CdTe films themselves and solar cells made from them. Techniques were developed for making measurements on films often less than 1 micron in thickness. The highest values achieved for efficiency parameters, not necessarily all in the same cell, were V/sub oc/ = 0.5 V, J/sub sc/ = 11 mA/cm/sup 2/, and fill factor = 0.55 before corrections in the absence of anti-reflection coatings. Typical resistivities for n-CdTe films were 10/sup 5/ ..cap omega..-cm. Lifetimes of about 10/sup -10/ sec were measured. Absorption coefficient of these films is in the order of 10/sup 4/ for lambda < 0.7 ..mu..m. Measured energy gap for these CdTe films is 1.55 eV, sightly higher than the 1.45 eV value for single crystal CdTe. The activation energy of the dominating trap level …

This report summarizes the results of Phase II of the High Velocity Particle Separator Program performed under Contract EF-77-C-01-2709. This high velocity wedge separator has the potential to reduce equipment size and cost of high temperature and pressurized particulate removal equipment for coal derived gases. Phase II has been directed toward testing and detailed conceptual design of an element suitable for a commercial scale high temperature, high pressure particle separator (HTPS). Concurrently, Phase IA has been conducted, which utilized the ambient analog method (AAM) for aerodynamic and collection performance investigation of each HTPS configuration prior and during hot testing. This report summarizes the results of Phase IA and II. The AAM effort established correlation of theoretical analysis and experiment for HTPS pressure drop, purge flow ratio and collection efficiency potential. Task I defined the initial test conditions to be the contract design point of 1800/sup 0/F and 350 psia. The 1800/sup 0/F, 350 psia testing represents the main high temperature testing with coal-derived particulates in the 2 to 10 micron range. Phase IA and Phase II have demonstrated efficient particle collection with acceptable pressure drop. In view of these encouraging results, it is reasonable to apply the developed technology toward …

Silicon dendritic web is a ribbon form of silicon produced from the melt without die shaping, and capable of fabrication into solar cells with greater than 15% AM1 conversion efficiency. This quarterly report describes the work carried out during the period April to June 1980, as part of Phase III of a DOE/JPL-sponsored effort to develop silicon web process technology compatible with the national goals for low cost photovoltaic output power. We have successfully demonstrated eight hours of silicon web growth with closed loop melt level control, a key contract milestone. The result was achieved using a feedback system in which the change in output from a laser melt level sensor was used to control the rate at which silicon pellets were fed to replace the material frozen into web crystal. The melt level was controlled to about +- 0.1mm, well within the range required for stable long term web growth. This is an important step toward the development of a fully automated silicon web growth machine. A second major highlight of this quarter was the completion of an engineering design for a semi-automated web growth machine embodying all the desired features developed so far as part of this program …

Potential ridges, now identified as the locus of breakdown of approximate separability of coordinates, require a special physico-mathematical treatment the initial phase of which has now been completed. The role of a potential ridge in separating the pair of exit channels of lower-energy two-electron excitations is circumscribed and hence accessible to numerical calculations; it has thus been studied in some detail for earth-alkaline-like configurations and for He/sup -/. Quantum defect theory approaches have been extended to molecular predissociation and to the study of Stark effect wave-functions; these extensions have now proved so far from the origins of the approach that a new name and description would be more appropriate.

The main research accomplishments during the past three years are summarized. The principle areas of investigation are: 1. embryotoxicity, teratogenicity, and mutagenicity of nickel carbonyl; 2. metabolism, detoxification, and excretion of nickel compounds; 3. studies of nickel carcinogenesis; 4. nickel analysis in body fluids and tissues to monitor occupational exposures; 5. nephrotoxicity of nickel compounds; and 6. hematological effects of nickel compounds. (ACR)

The price allocation guidelines (PAG) are an integrated set of specific cost targets for several task areas within the Low-cost Solar Array (LSA) Project. PAG is a working tool of LSA Project management designed to provide consistent and meaningful guidelines for costs of polycrystalline silicon material, sheet, cells, encapsulants, and module manufacturing. It is expected that advanced photovoltaic concepts derived from industry and the research community can be developed so that it will be possible by the end of 1982 to demonstrate production processes, all process steps, and prototype equipment required to manufacture flat-plate photovoltaic modules. This demonstration would incorporate production rates and product quality consistent with a specific market price determined by the program. This stage of development has been referred to as Technical Readiness. A goal of $0.70 per peak watt (1980 dollars) has been established for the cost of electricity generated by photovoltaic modules. The processes for producing modules demonstrated to be technically ready must be amenable to scale-up so that this price goal can eventually be achieved in the marketplace. The guidelines described in this document allocate portions of that goal to each module component. Sheet materials derived from the following five technologies are considered: Czochralski, …

In the second quarter of activities on developing Tailored Ceramic waste forms for SRP waste compositions, emphasis was on the chemistry controlling the incorporation of the waste elements into the crystalline phases of the high-alumina content ceramic and the major factors affecting the consolidation process. Research on the design and synthesis of oxide and phosphate ceramic waste forms has continued with emphasis on fluorite-structure oxides and on rare earth phosphates with the monazite structure. Dissolution studies to date indicate that monazite is very stable.

Most analytical and experimental approaches to the evaluation of fluid-structure interaction (FSI) effects in the General Electric Mark I BWR pressure suppression system treat the torus shell as rigid when the shell in real systems is flexible. This report describes linear three-dimensional finite-element analyses of one torus bay that investigated the qualitative effect of torus wall flexibility on hydrodynamic loads induced by a nominal safety relief valve (SRV) discharge. The results of these analyses support the general conclusion drawn from earlier two-dimensional analyses. The report also discusses finite-element analyses of a 3-D representation of the earlier 2-D plane-strain model of the torus shell.

An evaluation was completed to ascertain the applicability of line focus technologies to electrical power applications and to compare their performance and cost potential with point focus central receiver power systems. It was concluded that although the high temperature line focus (SRI) and fixed mirror line focus (GA) concepts duplicate the heat source characteristics and power conversion technology of the central receiver concepts these configurations do not offer a sufficient improvement in cost to warrant full scale development. The systems are, however, less complex than their point focus counterpart and should the central receiver system development falter they provide reasonable technology alternatives. The parabolic trough concept (BDM) was found to provide a low temperature technology alternative to the central receiver concept with promising performance and cost potential. Its continued development is recommended, with special emphasis on lower temperature (< 700/sup 0/F) applications. Finally, a variety of new promising line focus power system configurations were identified for a range of utility and industrial applications and recommendations were made on their implementation. This volume contains the detailed report. (WHK)

Proton magnetic resonance data are presented for plasma-deposited amorphous Si:H as a function of annealing temperature up to 650/sup 0/C. The data indicate that hydrogen diffuses internally before major evolution occurs, that transfer of hydrogen occurs from a heavily clustered phase to a dilute phase coincident with evolution and that evolution occurs initially from the heavily clustered phase. Comparison with infrared data indicates that the heavily clustered phase can be either SiH/ sub x/t = 2,3) or SiH.