Memorandum presenting a calculation of the amount of possible correction for coordinated turns with limited bank angle and level sideslips for a large transport airplane, the C-54D. The results indicate that for all instances from the end of the runway, coordinated turns are the more effective maneuver.

Report presenting surveys of the flow of the asymmetric adjustable nozzle of the 6- by 6-foot supersonic wind tunnel, which were made to determine the uniformity of the air stream. Test techniques for minimizing the effects of stream irregularities and the results of force and pressure-distribution tests of a swept-wing model are presented to illustrate the effectiveness of these techniques.

Report presenting an analysis to determine the applicability of existing propeller theory and the theory of oscillating airfoils to the problem of determining the magnitude of the forces on propellers in pitch or yaw. The steady-state method for calculating propeller forces appears to give satisfactory results.

Memorandum presenting an investigation of the change in spanwise load distribution at high Mach numbers, which is of considerable interest because lateral movement of the center of lift affects the trim, stability, and structural factors of safety of an airplane. The data is not sufficient to permit isolation of the effects of changes in wing configuration, but in a majority of cases, the tests reveal a tendency for the center of lift to shift outboard with increasing Mach number.

Report presenting the results of pitching-moment, lift, and drag measurements on a model of the D-558-1 with speed reduction brakes and a symmetrical profile wing at a range of Mach numbers. Only a small decrement in Mach number is produced with no nose-inlet flow and the speed-reduction brakes deflected.

The results of power-off force tests and flight tests of a model with a thin unswept low-aspect-ratio wing are presented. The tests were made with the flaps retracted and deflected. The effects on the lateral flight characteristics of decreasing directional stability were noted.

Report presenting wind-tunnel testing to determine the independent effects of Mach and Reynolds numbers on the aerodynamic characteristics of a wing-fuselage combination with a wing with the leading edge swept back 63 degrees and with camber and twist. Results regarding the fuselage alone and the effects of camber and twist are also provided.

Report presenting an investigation of the effects of various mass, aerodynamic, and dimensional parameters on the dynamic lateral stability of the Douglas D-558-2 airplane. Results regarding an airplane with the flaps and gear retracted, airplane at sea level with flaps deflected 50 degrees and landing gear lowered, and effect of assumed modifications to airplane are provided.

Report presenting tests to determine the recovery of total pressure attainable at a range of Mach numbers, which were performed with models with twin-scoop inlets situated on the sides of a long forebody. Results regarding ducts without slots and ducts with slots are provided.

Investigation conducted in the altitude wind tunnel to study the effect of Reynolds number on the performance of an axial-flow compressor. The compressor was operated as a part of a turbojet engine over a range of pressure altitudes and compressor-inlet Reynolds numbers. Results regarding compressor efficiency, air flow, and a comparison with axial-flow compressors of different design are provided.

Memorandum presenting a study to determine the possible blending agents or additives that may be used to supplement current high performance number, rich rating components in future aviation fuels. The study indicated that such high rich rating blending agents as toluene and xylene cannot be made available in sufficient quantities to maintain the rich rating performance of the fuels when reducing the lead content from 4.6 to 3.0 ml per gallon.

From Introduction: "Thrust augmentation of an axial-flow-type turbojet engine by burning fuel in the tail pipe is discussed in references 1 to 3. Thrust augmentation of the same turbojet engine by water injection at the compressor inlet is reported in reference 4."

Report presenting an investigation of the operation of two submerged-type inlets in a wind tunnel at subsonic and transonic speeds. The pressure recovery was relatively constant throughout the lower subsonic speed range. The ability of the divergent-walled inlet to operate with satisfactory pressure recovery at higher free-stream Mach numbers than was possible with the parallel-walled inlet is attributed to the difference in the boundary-layer characteristics of the two types of inlets.

Report discussing tests of an unshrouded axial-flow supersonic compressor rotor. Information about the pressure ratio, efficiency, and flow rate with and without inlet guide vanes is provided. The results are also compared to testing on the original shrouded rotor.

Report presenting an investigation in the transonic tunnel on the effect of sweepback angle on the wing-body characteristics at a range of Mach numbers. Results regarding lift characteristics, drag characteristics, and pitching-moment characteristics are provided.

"An experimental investigation in the Langley Gas Dynamics Laboratory has been made of the flow separation from slender rods mounted to extend forward along the axes of symmetry of blunt-nosed bodies. The mechanism of the separation and its governing criteria are discussed. Drag data at a Mach number of 2.72 for various rod lengths and nose radii at an angle of attack of zero degrees are presented. It was found that the drag coefficients of blunt noses could be appreciably reduced by the use of protruding rods. Criteria for rod length which gives lowest drag are given" (p. 1).

Report presenting an investigation in the pressure wind tunnel to determine the effect of an operating propeller on the aerodynamic characteristics of a model of a vertical-rising airplane with an unswept wing with an aspect ratio of 3. Lift, longitudinal force, pitch, and roll characteristics, with and without power, are presented for the complete model and various combinations of model components.

The effectiveness of molybdenum disulfide MoS2 as a bearing lubricant was determined at high temperature and at high speeds. A 1-inch-bore ball bearing operated at temperatures to 1000 F, a speed of 1725 rpm, and a thrust load of 20 pounds when lubricated only with MoS2-air mist. A 75-millimeter-bore cageless roller bearing, provided with a MoS2-syrup coating before operation, operated at DN values to 1 x 10(exp 6) with a load of 368 pounds.

Report presenting the results of a free-flight investigation of two drag research models equipped with canopies for a range of Mach numbers from 0.8 to 1.5. The main difference between the models was the location of the canopy, which was at the 15-percent fuselage station on one model and the 25-percent fuselage station on the other. The additional drag due to the canopies was about 10 to 20 percent of the total configuration drag at supersonic speeds.

Report presenting the horizontal-tail load measurements obtained during testing of the Bell X-5 airplane at the NACA High-Speed Flight Research Station. Measurements were taken at a range of Mach numbers and from sweep angles of 20 degrees to 59 degrees.

Report presenting analytical methods to calculate average and local turbine-blade temperatures. The temperatures were compared with experimental data obtained in a forced-convection, water-cooled aluminum turbine over a range of turbine-inlet-gas temperatures and coolant-mass velocities. Results regarding comparison of calculated and experimental aluminum turbine blade temperatures, comparison of calculated and experimental stationary-blade temperatures, stationary water-cooled blade operating data, and turbine operating data are provided.

Memorandum presenting an investigation of the rolling effectiveness of a partial-span, perforated spoiler on a wing with 45 degrees of sweepback at Mach numbers from 0.25 to 0.96. The effects of the spoiler on the lift, drag, and pitching moment were also determined. Results regarding Reynolds number, Mach number, and predicted rate of roll are provided.

Report presenting a wind-tunnel investigation at low speeds to determine the lateral-control and hinge-moment characteristics of a 20-percent-chord, unsealed, partial-span outboard aileron equipped with an overhang, a paddle, or a spoiler balance on a tapered 51.3 degree sweptback semispan wing model with an aspect ratio of 3.05. The aileron effectiveness was not greatly affected by the overhang or paddle balance, but the spoiler balance increased the effectiveness obtained with the plain flap.

Report presenting an investigation to study some factors affecting the drag of relatively large nonlifting bodies of revolution at transonic speeds in the 8-foot transonic tunnel. Drag and surface pressure measurements were made for two geometrically similar bodies of revolution of 8-inch and 4-inch maximum diameter at zero angle of attack through a range of Mach numbers.