From introduction: "This is the eighteenth in a series of quarterly reports which cover the progress and results from the conceptual designs, economic evaluations and research and development work performed by the General Electric Company as part of Contract AT(01-3)-189, Project Agreement No. 13."

Abstract: Residual and fission gas release from UO2 were studied in the laboratory and in in-reactor experiments. Arc-fused powder and sintered pellets were used to determine the rate of evolution and types of residual gases as a function of temperature. Fission gas release was related to the average UO2 temperature and fission gas release calculations were made using the latest thermal conductivity values, isotopic half lives, and branching ratios available in the literature. The results obtained were compared with those available in the literature, and a satisfactory agreement was found among the groups of comparable data.

From introduction: "This is the sixteenth in a series of quarterly reports which cover the progress and results from the conceptual designs, economic evaluations and research and development work performed by the General Electric Company as part of Contract AT(01-3)-189, Project Agreement No. 13."

Activities in a program to develop techniques in the use of pulsed neutron sources to measure shutdown parameters related to large thermal power reactors are reported. The development of pulsed neutron source techniques for large power reactors has led to a new theoretical model recently developed by E. Garelis and J.L. Russell, Jr. The theory is presently based on a bare, one-group model with m-delayed precursors and takes all spatial modes into account. Results indicate, however, that the application of this model is much broader. Experiments were designed and carried out to both verify this new theory and to demonstrate the performance of the experimental hardware in a large power reactor.

Technical report describing that as part of the AEC Fuel Cycle Program, tests are being conducted to evaluate the significance of current fuel design limitations that do not permit the maximum fuel temperature to exceed the melting point of UO2. The reliability of prediction of the fuel rod operating conditions that will cause melting of the UO2 was evaluated by means of a calibration test conducted in the Vallecitos Boiling Water Reactor. Conclusions: (a) The central portion of the 3.15-cm diameter uranium dioxide fuel column melted. It appears that the UO2 was molten to a radius of 1.22 cm in the peak power region. The maximum extent of melting probably occurred during the peak power run when the kdT in this region of the rod reached 171 watts cm. The estimated radius of melting from metallographic examination indicates the kdT for sintered UO2 is 89 watts/cm. This supports a calculated estimate for sintered UO2 thermal conductivity published by D. R. deHalas and G. R. Horn. The results of the previous calibration run and subsequent experimental data by Lyons are also consistent with the value. This conclusion is contingent on the interpretation of the post-irradiation crystal structure of the UO2. Insufficient …

From introduction: "This is the seventeenth in a series of quarterly reports which cover the progress and results from the conceptual designs, economic evaluations and research and development work performed by the General Electric Company as part of Contract AT(01-3)-189, Project Agreement No. 13."

Summary: A prototype control rod containing absorber plates made from an electro- deposited dispersion of boron carbide in nickel was tested in the VBWR. It was exposed to the reactor environment of 545 degree F boiling water and thermal neutron fluxes (perturbed) which ranged from 0.6 to 1.1 x 10/sup 13/ nv for 2236 hours over a period of six months. The maximum B/sup 10/ burnup achieved during the test period was 1.8 percent. After irradiation, the rod was examined. The results of the examination are summarized below: (1) The B/sub 4/C-- Ni plate assembly did not undergo significant dimensional changes during irradiation. (2) Numerous blisters developed on both the outer and inner surfaces of three of the four plates. Blistering was more severe on the outer surface than on the inner, and was most severe in a large region located in the lower half of plate 4. Metallographic examination revealed that the blisters were located only in the 2- mil protective nickel overlay covering the B/sub 4/C-- Ni dispersion. It was concluded that they formed from the buildup of gas pressure at the Ni: Ni-- B/sub 4/C interfaces, rather than from corrosion attack. Helium from the B/sup 10/(n alpha …

Activities in a program to develop techniques in the use of pulsed neutron sources to measure shutdown parameters related to large thermal power reactors are reported. The development of pulsed neutron source techniques for large power reactors has led to a new theoretical model recently developed by E. Garelis and J.L. Russell, Jr. The theory is presently based on a bare, one-group model with m-delayed precursors and takes all spatial modes into account. Results indicate, however, that the application of this model is much broader. Experiments were designed and carried out to both verify this new theory and to demonstrate the performance of the experimental hardware in a large power reactor.

Quarterly progress report discussing activities related to the Vallecitos Boiling Water Reactor (VBWR) and related facilities.