This report follows the studies on the interactions of antiproton with ordinary matter.

The antiproton--proton interaction was studied at three energies, 2.0, 1.25, and 0.98 Bev. Antiprotons produced internally in the Revatron and channeled externally by a system of bending magnets and quadrupoles were selected from background particles by using a gas Cherenkov counter and scintillation counters. At the two lower energies, an electrostatic-magnetic velocity spectrometer was used to reject background particles. A liquidhydrogen target was completely surrounded by scintillation counters so that all charged secondaries from the antiproton--proion interactions could be detected. With the information obtained from these counters, the --p-bar--p total, elastic, inelastic, and charge-exchange cross sections and the angular distribution of the elastic scatterings were obtained at each energy. The total cross section was found to be 80, 89, and 100 mb at 2.0 1.25. and 0.98 Bev. respeclively. The inelastic cross section was about twothirds of ihe total cross section at each energy. It was found that each of the partial cross sections was dropping off slowly with energy. The results were fitted by an optic al-model c alculation. (auth)

A mass-spectrometric investigation was performed on sulfur vapor in equilibrium with the condensed phase at 120 to 210 gas-cooled C. It was found that, in this temperature range, equilibrium sulfur vapor contains appreciable quantities of S/sub 8/, S/sub 7/, S/sub 6/, and S/sub 5/ only. The sulfur vapor emanated as a small well-collimated molecular beam from a specially constructed source into an ionization chamber which was designed to exclude from analysis any sulfur vapor that had impinged on the walls or the hot electron filament. Essential identical ionization potentials were determined for S/sub 8/ , S/sub 7/, S/sub 6/, and S/sub 5/ of 9.8 0.4 ev. The heat of vaporizati on of S/sub 7/ was calculated to be approximately 2.5 kcal greater than that of S/ sub 8/. Upper limits for S/sub 8/ and S/sub 7/ composition in S vapor at 120 gas- cooled C were determined to be 86% and 14%, respectively. It is proposed thst S/sub 8/ is the vaporizing species, that S/sub 7/, S/sub 6/, and S/sub 5/ result from dissociation of S/sub 8/. and that all four molecules have a ring configuration. (auth)

The inelastic interactions of negative pi mesons with protons at 374, 417, and 454 Mev incident pi kinetic energy are studied by measuring the differential distributions of finalstate neutrons. The pi source is an internal target of the Berkeley 184-inch synchrocyclotron. A magnetic beamtransport system momentum-anaiyzes and focuses the pi beam at a liquid hydrogen target located in an adjacent shielded experimental area. The time-of- flight distribution of neutral particles is measured at various laboratorysystem angles between 10 and 65 deg. Neutral particles are detected by observing the charged products of their interactions in plastic scintillator. The time-of- flight information is determined electronically by time-to-height conversion and pulse-height analysis. The time resolution of the total system is 1.0 nsec. Detected neutral particles accompanied by charged particles are separated by the electronic system from those not accompanied by charged particles. Analysis presuming the principal inelastic reactions to be pi /sup -/p yields pi /sup +/ pi /sup -/n and pi /sup -/p yields pi /sup 0/ pi /sup 0/n separates the time-of-flight spectra into gamma rays, neutrons from the reaction pi /sup -/p yields pi /sup 0/n, and inelastic neutrons. Calculated values of the neutron- detection efficiency are used in the …

In Part One they formulate in a general way the problem of analyzing and evaluating the aberrations of quadrupole magnet beam systems, and of characterizing the shapes and other properties of the beam envelopes in the neighborhood of foci. They consider all aberrations, including those due to misalignments and faulty construction, through third order in small parameters, for quadrupole beam systems. One result of this study is the development of analytic and numerical techniques for treating these aberrations, yielding useful expressions for the comparison of the aberrations of different beam systems. A second result of this study is a comprehensive digital computer program that determines the magnitude and nature of the aberrations of such beam systems. The code, using linear programming techniques, will adjust the parameters of a beam system to obtain specified optical properties and to reduce the magnitude of aberrations that limit the performance of that system. They examine numerically, in detail, the aberrations of two typical beam systems. In Part Two, they examine the problem of extracting the proton beam from a synchrotron of 'H' type magnet construction. They describe the optical studies that resulted in the design of an external beam from the Bevatron that is …

None

This thesis describes the design, selection and scale model test results of a contour design for a convectively-cooled, ground test nozzle extension which originates at an area ratio of 5:1 (termination point of main nozzle).

None

The nonlinear coupling of intense, monochromatic, electromagnetic radiation with plasma is considered in a number of special cases. The first part of the thesis serves as an introduction to three-wave interactions. A general formulation of the stimulated scattering of transverse waves by longitudinal modes in a warm, unmagnetized, uniform plasma is constructed. A general dispersion relation is derived that describes Raman and Brillouin scattering, modulational instability, and induced Thomson scattering. Raman scattering (the scattering of a photon into another photon and an electron plasma wave) is investigated as a possible plasma heating scheme. Analytic theory complemented by computer simulation is presented describing the nonlinear mode coupling of laser light with small and large amplitude, resonantly excited electron plasma waves. The simulated scattering of a coherent electromagnetic wave by low frequency density perturbations in homogeneous plasma is discussed. A composite picture of the linear dispersion relations for filamentation and Brillouin scattering is constructed. The absolute instability of Brillouin weak and strong coupling by analytic and numerical means is described. (auth)

The investigation of two poorly understood but technologically important physical properties of silicate glasses and related materials is described. The use of Electron Paramagnetic Resonance to investigate the nature of radiation-induced damage in glasses exposed to a variety of high-energy radiation sources is discussed first. Second, the measurement of the nonlinear index of refraction coefficient in a variety of optical materials related to the design of high-power laser systems is described. The radiation damage investigations rely heavily on the comparison of experimental results for different experimental situations. The comparison of EPR lineshapes, absolute spin densities and power saturation behavior is used to probe a variety of microscopic and macroscopic aspects of radiation damage in glasses. Comparison of radiation damage associated with exposure to gamma rays and fast neutrons (and combinations thereof) are interpreted in terms of the microscopic damage mechanisms which are expected to be associated with the specific radiations. Comparison of radiation damage behavior in different types of glasses is also interpreted in terms of the behavior expected for the specific materials. The body of data which is generated is found to be internally self-consistent and is also generally consistent with the radiation damage behavior expected for specific situations. …

A thesis, Assessing Student Achievement in Art, A Study of The Feasibility of Achievement Testing in Art. Submitted to: The Getty Center for Education in the Arts, The J. Paul Getty Trust by Ralph Hoepfner, Ph.D. The report on feasibility of developing curriculum-fair achievement tests the art on both positive and negative notes. During the 1983-84 school year an achievement test was developed to assess the school children's knowledge.

The Cloudy Quark Bag Model is extended from S-wave to P- and D-wave. The parameters of the model are determined by K{sup {minus}}p scattering cross section data, K{sup {minus}}p {yields}{Sigma}{pi}{pi}{pi} production data, K{sup {minus}}p threshold branching ratio data, and K{sup {minus}}p {yields}{Lambda}{pi}{pi}{pi} production data. The resonance structure of the {Lambda}(1405), {Sigma}(1385), and {Lambda}(1520) are studied in the model. The shift and width of kaonic hydrogen are calculated using the model.

Results are presented here from several two dimensional numerical calculations of events in Type II supernovae. A new 2-D hydrodynamics and neutrino transport code has been used to compute the effect on the supernova explosion mechanism of convection between the neutrinosphere and the shock. This convection is referred to as exterior convection to distinguish it from convection beneath the neutrinosphere. The model equations and initial and boundary conditions are presented along with the simulation results. The 2-D code was used to compute an exterior convective velocity to compare with the convective model of the Mayle and Wilson 1-D code. Results are presented from several runs with varying sizes of initial perturbation, as well as a case with no initial perturbation but including the effects of rotation. The M&W code does not produce an explosion using the 2-D convective velocity. Exterior convection enhances the outward propagation of the shock, but not enough to ensure a successful explosion. Analytic estimates of the growth rate of the neutron finger instability axe presented. It is shown that this instability can occur beneath the neutrinosphere of the proto-neutron star in a supernova explosion with a growth time of {approximately} 3 microseconds. The behavior of the …

In the United States we generate greater than 500 million tons of toxic waste per year which pose a threat to human health and the environment. Some of the most toxic of these wastes are those that are radioactively contaminated. This thesis explores the need for permanent disposal facilities to isolate radioactive waste materials that are being stored temporarily, and therefore potentially unsafely, at generating facilities. Because of current controversies involving the interstate transfer of toxic waste, more states are restricting the flow of wastes into - their borders with the resultant outcome of requiring the management (storage and disposal) of wastes generated solely within a state`s boundary to remain there. The purpose of this project is to study nuclear waste storage issues and public perceptions of this important matter. Temporary storage at generating facilities is a cause for safety concerns and underscores, the need for the opening of permanent disposal sites. Political controversies and public concern are forcing states to look within their own borders to find solutions to this difficult problem. Permanent disposal or retrievable storage for radioactive waste may become a necessity in the near future in Colorado. Suitable areas that could support - a nuclear storage/disposal …

The Department of Energy`s program for disposing of nuclear High-Level Waste (HLW) and transuranic (TRU) waste has been impeded by overwhelming political opposition fueled by public perceptions of actual risk. Analysis of these perceptions shows them to be deeply rooted in images of fear and dread that have been present since the discovery of radioactivity. The development and use of nuclear weapons linked these images to reality and the mishandling of radioactive waste from the nations military weapons facilities has contributed toward creating a state of distrust that cannot be erased quickly or easily. In addition, the analysis indicates that even the highly educated technical community is not well informed on the latest technology involved with nuclear HLW and TRU waste disposal. It is not surprising then, that the general public feels uncomfortable with DOE`s management plans for with nuclear HLW and TRU waste disposal. Postponing the permanent geologic repository and use of Monitored Retrievable Storage (MRS) would provide the time necessary for difficult social and political issues to be resolved. It would also allow time for the public to become better educated if DOE chooses to become proactive.

The differential geometry on a Hopf algebra is constructed, by using the basic axioms of Hopf algebras and noncommutative differential geometry. The space of generalized derivations on a Hopf algebra of functions is presented via the smash product, and used to define and discuss quantum Lie algebras and their properties. The Cartan calculus of the exterior derivative, Lie derivative, and inner derivation is found for both the universal and general differential calculi of an arbitrary Hopf algebra, and, by restricting to the quasitriangular case and using the numerical R-matrix formalism, the aforementioned structures for quantum groups are determined.

The equations of motion describing turbulent flows (in both the low and high Reynolds-number regimes) are well established. However, present day computers cannot meet the enormous computational requirement for numerically solving the governing equations for common engineering flows in the high Reynolds number turbulent regime. The characteristics that make turbulent, high Reynolds number flows difficult to simulate is the extreme range of time and space scales of motion. Most current engineering calculations are performed using semi-empirical equations, developed in terms of the flow mean (average) properties. These turbulence{open_quote} models{close_quote} (semi-empirical/analytical approximations) do not explicitly account for the eddy structures and thus, the temporal and spatial flow fluctuations are not resolved. In these averaging approaches, it is necessary to approximate all the turbulent structures using semi-empirical relations, and as a result, the turbulence models must be tailored for specific flow conditions and geometries with parameters obtained (usually) from physical experiments. The motivation for this research is the development of a finite element turbulence modeling approach which will ultimately be used to predict the wind flow around buildings. Accurate turbulence models of building flow are needed to predict the dispersion of airborne pollutants. The building flow turbulence models used today are not …

The work described in this report was carried out at a national laboratory of the Department of Energy, during the time that the author was engaged in a Department of Energy Industrial Hygiene Graduate Fellowship. The national laboratory had a respiratory protection program with approximately 50 employees participating. The program was in place to protect employees from over-exposure to airborne contaminants while engineering and work practice controls were being installed and implemented. It was also in place to protect workers in situations where engineering and work control practices were not feasible, such as during maintenance and repair work, as well as in situations where engineering and work practice controls were not enough to lower the exposure to or below the Permissible Exposure Limit (PEL) as set by the Occupational Safety and Health Association (OSHA) as an eight-hour time weighted average (TWA) or an excursion limit. Respirators were also used for emergencies by the emergency response team.

Atmospheric iron (Fe) is thought to play an important role in cloudwater chemistry (e.g., S(IV) oxidation, oxidant production, etc.), and is also an important source of Fe to certain regions of the worlds oceans where Fe is believed to be a rate-limiting nutrient for primary productivity. This thesis focuses on understanding the chemistry, speciation and abundance of Fe in cloudwater and aerosol in the troposphere, through observations of Fe speciation in the cloudwater and aerosol samples collected over the continental United States and the Arabian Sea. Different chemical species of atmospheric Fe were measured in aerosol and cloudwater samples to help assess the role of Fe in cloudwater chemistry.

Mortandad Canyon is a discharge site for treated industrial effluents containing radionuclides and other chemicals at Los Alamos National Laboratory, New Mexico. This study was conducted to develop an understanding of the unsaturated hydrologic behavior below the canyon floor. The main goal of this study was to evaluate the hypothetical performance of the vadose zone above the water table. Numerical simulations of unsaturated groundwater flow at the site were conducted using the Finite Element Heat and Mass Transfer (FEHM) code. A two-dimensional cross-section along the canyon's axis was used to model flow between an alluvial groundwater system and the regional aquifer approximately 300 m below. Using recharge estimated from a water budget developed in 1967, the simulations showed waters from the perched water table reaching the regional aquifer in 13.8 years, much faster than previously thought. Additionally, simulations indicate that saturation is occurring in the Guaje pumice bed an d that the Tshirege Unit 1B is near saturation. Lithologic boundaries between the eight materials play an important role in flow and solute transport within the system. Horizontal flow is shown to occur in three thin zones above capillary barriers; however, vertical flow dominates the system. Other simulations were conducted to …

Partial transient liquid phase (PTLP) bonding is a technique which can be used to join ceramics with metals and is used to form niobium-based joints for alumina. The principal advantage to PTLP bonding is that it enables refractory joints to be fabricated at temperatures below those typically required by solid state diffusion bonding. A thorough review of the important parameters (chemical compatibility, thermal expansion match, sufficient wettability of the liquid phase on the solid phases) in choosing a joining material for ceramics by the PTLP method is provided. As in conventional PTLP joining, the current study uses thin (=3 (mu)m) copper layers sandwiched between the alumina (bulk) and niobium (127 (mu)m). However, unlike the case of copper/nickel/copper obium is limited. Consequently, the copper is not entirely dissolved in the process, resulting in a two phase (copper-rich and niobium-rich phases) microstructure. Different processing conditions (temperature and applied load) result in different morphologies of the copper-rich and niobium-rich phases at the interface. These different microstructures exhibit distinct strength characteristics. Extended annealing of as-processed joints can influence the strengths differently depending on the ambient partial oxygen pressure at the annealing temperature. The focus of this work is to correlate processing conditions, microstructure, and …

This dissertation reports on measurements of inclusive cross sections times branching fractions into electrons for W and Z bosons produced in p{anti p} collisions at {radical}s = 1.8 TeV. From an integrated luminosity of 84.5 pb{sup {minus}1} recorded in 1994--1995 by the D0 detector at the Fermilab Tevatron {Lambda} the cross sections are measured to be {sigma}p{anti p} {r_arrow} W + X {center_dot} B(W {r_arrow} e{nu}) = 2,310 {+-} 10 (stat) {+-} 50 (Syst) {+-} 100 (lum) pb and {sigma}(p{anti p} {r_arrow} Z + X) {center_dot} B(Z {r_arrow} ee) = 221 {+-} 3 (stat) {+-} 4 (Syst) {+-} 10 (lum) pb. The cross section ratio R is determined to be {sigma}(p{anti p} {r_arrow} W + X) {center_dot} B(W {r_arrow} e{nu})/{sigma}(p{bar p} {r_arrow} Z + X) {center_dot} B(Z {r_arrow} ee) = 10.43 {+-} 0.15 (stat) {+-} 0.20 (syst) {+-} 0.10 (NLO){Lambda} and R is used to determine B(W {r_arrow} e{nu}) = 0.1044 {+-} 0.0015 (stat) {+-} 0.0020 (syst) {+-} 0.0017 (theory) {+-} 0.0010 (NLO){Lambda} and {Lambda}{sub W} = 2.169 {+-} 0.031 (stat) {+-} 0.042 (syst) {+-} 0.041 (theory) {+-} 0.022 (NLO) GeV. The latter is used to set a 95% confidence level upper limit on the partial decay width of the …

We attempt to identify a single top signal in the muon + jets data collected using the D0 detector at the Fermilab Tevatron at a center-of-mass energy of {radical}s = 1.8 TeV from 1992-96. The data corresponds to an integrated luminosity of 103.7 pb{sup -1}. While resolving a signal has proved impossible, we are able to place an upper limit on the production cross section for single top events using these data. The cross section for production of single top via 95% p{bar p} {yields} tb and p{bar p} {yields} qtb is less than 78 pb at the 95% confidence level based on muon + jets data only.

The Standard Model predicts that the lifetime of the top quark is shorter than the typical time scale at which hadronization process occurs, and the spin information at its production is preserved. Spin correlation of the t{anti t} system from p{anti p} collisions at the Tevatron is analyzed using 6 events in the dilepton channels collected using the D0 detector. Spin correlation factor of {kappa} > {minus} 0.25 at 68% CL is obtained from the data.