Report presenting an experimental investigation to determine the effect of boundary-layer control and inlet lip shape on the performance of a side-inlet air-induction system for a fighter-type airplane. Two methods of boundary layer control and three inlet lip shapes were investigated at a range of Mach numbers and mass-flow ratios. Results regarding net propulsive thrust are also provided.

Memorandum presenting a wind-tunnel investigation in which dynamic models that included elastic simulation were used to study the flight characteristics of a swept-wing bomber with parasite swept-wing fighters coupled at the wing tips. The configuration is meant to represent an efficient towing arrangement whereby the operational range of fighters can be increased.

Report presenting an investigation at subsonic and transonic speeds to determine the aerodynamic characteristics of three geometrically similar wings with 42 degree sweepback of the leading edge, aspect ratio 4, taper ratio 0.625, and NACA 64(sub)1-112 airfoils. The lift, drag, and pitching-moment characteristics are provided.

This report presents measurements of the lift and pitching-moment characteristics of a straight wing of aspect ratio 4, taper ratio 0.5, having a symmetrical double-wedge airfoil section with a maximum thickness of 4.4-percent chord. The tests were conducted in the Mach number range 0.51 to 1.20, Reynolds numbers 380,000 to 660,000, by the NACA wing-flow method. The results are compared with theory and with wind-tunnel tests of a similar model. It is indicated that in the Mach number range 0.82 to 1.00 the model surface, profile, and test Reynolds number all would be very important considerations in any attempt to study or predict full-scale characteristics from small-model tests.

A report in a series of five that present unanalyzed pressure data obtained in tests of five full-scale propellers with NACA 16-series blade sections. Pressure distributions on the blade sections were measured under operating conditions to determine the aerodynamic characteristics of each blade section. This particular report presents information for nine radial stations of the NACA 10-(3)(049)-033 propeller.

Memorandum presenting the pressure recovery, mass flow, and drag of a twin-scoop inlet-body combination measured at Mach numbers 1.4 and 1.7 at zero angle of attack. Tests were made of the inlet-body combination with an ogival forebody, an ogival forebody with a small amount of bluntness near the tip, and two forebodies of elliptical longitudinal section. Results regarding the effect of forebody bluntness on pressure recovery, effect of forebody bluntness on mass-flow ratio, and the effects of forebody bluntness on drag are provided.

Memorandum presenting a study using a suspended flat plate to continuously vary the Mach number in the 18- by 18-inch Mach number 1.91 supersonic tunnel. The technique was applied to the determination of pressure recovery and mass-flow characteristics of four supersonic nose inlets over the Mach number range produced. Results regarding the plate calibration and inlet performance are provided.

Memorandum presenting an investigation conducted in the Lewis 8- by 6-foot supersonic wind tunnel to determine the force and pressure characteristics of an all-external compression inlet with a conical spike and a supersonic cowl lip. Measurements of lift, drag, pitching moment, and internal and external pressures were made at free-stream Mach numbers of 1.59, 1.79, and 1.99 for a range of mass-flow ratios and angles of attack to 10 degrees.

From Introduction: "The purpose of this report is to present the results of the investigation, to compare the coolant-flow requirements of the two configurations, and to show what advantages an air-cooled internal-strut-supported blade may have over an equivalent shell-supported air-cooled blade."

"The modifications in the pressure distributions and the aerodynamic coefficients associated with additions of heat to the two-dimensional supersonic in viscid flow field adjacent to the lower surface of of a 5-percent-thickness symmetrical circular-arc wing are presented in this report. The pressure distributions are obtained by the use of graphical method which gives the two-dimensional supersonic inviscid flow field obtained with moderate heat addition. The variation is given of the lift-drag ratio and of the aerodynamic coefficients of lift, drag, and moment with free stream Mach number, angle of attack, and parameters defining extent and amount of heat addition" (p. 1).

Report presenting an investigation conducted with a conventional turbojet fuel, MIL-F-5624 (JP-3), and a low-volatility, high-density hydrocarbon, monomethylnaphthalene, in a vaporizing-type combustor to determine the combustion efficiency for variations in inlet-air conditions and fuel flow and to what extent fuel vaporization would minimize differences in combustion efficiency between the two fuels. Results regarding the performance of the combustor, correlation parameter, pressure-drop characteristics, and other miscellaneous observations are provided.

Report presenting an investigation of the F9F-4 airplane to evaluate a high-energy blowing boundary-layer-system in flight in order to improve the maximum lift characteristics of airplane wings. A high-energy blowing-boundary-layer control system was installed by the Grumman Aircraft Engineering Corporation. A series of test flights were made to measure the lift and drag variations with changes in angle of attack for the flap and gear both up and down and for blowing on and off.

Report presenting a wind-tunnel investigation in which dynamic models that included elastic simulation to study the flight characteristics of a swept-wing bomber with parasite swept-wing fighters coupled at the wing tips. The configuration represents an efficient owing arrangement in which the operational range of fighters can be increased. Results regarding the bomber alone, fighter coupled wing tip to wing tip, and fighter coupled on boom are provided.

From Introduction: "The purpose of this paper is to review new and significant data which will be of interest to designers in determining the heating of these components. A comparison with existing theory to indicate its adequacy in each case is also presented."

"This report contains the results of tests of a 1/3-scale model of the Lockheed YP-90A "Shooting Star" airplane and a comparison of drag, maximum lift coefficient, and elevator angle required for level flight as measured in the wind tunnel and in flight. Included in the report are the general aerodynamic characteristics of the model and of two types of dive-recovery flaps, one at several positions along the chord on the lower surface of the wing and the other on the lower surface of the fuselage. The results show good agreement between the flight and wind-tunnel measurements at all Mach numbers" (p. 1).

Flight and ground investigations have been made to compare an exhaust-ejector installation with a standard exhaust-collector-ring installation on air-cooled aircraft engines in a twin-engine airplane. The ground investigation allowed that, whereas the standard engine would have overheated above 600 horsepower, the engine with exhaust ejectors cooled at take-off operating conditions at zero ram. The exhaust ejectors provided as much cooling with cowl flaps closed as the conventional cowl flaps induced when full open at low airspeeds. The propulsive thrust of the exhaust-ejector installation was calculated to be slightly less than the thrust of the collector-ring-installation.

"An untwisted wing, which when unswept has an NACA 65-210 section, an aspect ratio of 9.0 and a taper ration of 2.5:1.0, has been tested with no sweep, and 30 deg and 45 deg of sweepback and sweepforward in conjunction with a typical fuselage at Mach numbers from 0.60 to 0.96 at angles of attack generally between -2 deg and 10 deg in the Langley 8-foot high-speed tunnel. Sweep was obtained by rotating the wing semispans about a point in the plane of symmetry. The normal-force, pitching-moment, profile-drag, and loading characteristics for the wings have been obtained from pressure measurements and wake surveys" (p. 1).

"At the request of the Bureau of Aeronautics, Department of the Navy, an investigation of the Westinghouse XJ34-WE-32 turbojet engine is being conducted in the NACA Lewis altitude wind tunnel to determine the steady-state and transient operating characteristics of the controlled and uncontrolled engine at various altitudes and ram pressure ratios. As part of this program, transient performance data that illustrate the operation of the engine is obtained in the form of oscillographic traces. Similar data for engine operation in the afterburning range, covering a range of throttle settings from the minimum value giving rated speed (throttle position, 72 degrees) to full afterburning (throttle position, 110 degrees), is presented herein" (p. 1).