Report presenting calculated performance characteristics of a ducted rocket with gasoline and liquid oxygen as the fuel mixture and with a mass flow of 1 slug per second. Evaluations of net thrust, frontal area, thrust per unit frontal area, and specific fuel consumption are given for all of the flight conditions under which it might operate.

Report presenting an investigation to obtain a survey of the flying characteristics at low speeds of models with low-aspect-ratio delta wings. Four models with triangular plan-form sweptback wings and five models with the tips cut off to give taper ratios were tested. Results regarding the stability and control characteristics of each of the models is provided.

Report presenting flight measurements obtained during acceptance tests conducted by the Bell Aircraft Corporation on the XS-1 research airplane. The primary focus was on the aerodynamic loads, handling qualities, maximum lift, and buffet boundaries of the airplane.

The effects on dynamic lateral stability and controllability of some of the important aerodynamic and mass characteristics are discussed and methods are presented for estimating the various stability parameters to be used in the calculation of the dynamic lateral stability of airplanes with swept and low-aspect-ratio wings.

Report presenting transonic speed testing utilizing a rocket-powered Bell XS-1 airplane with 10-percent-thick wing and 8-percent-thick horizontal tail. Information is provided for flights up to Mach number 1.06 and altitudes of about 40,000 feet. Results regarding the variation of control-surface positions and forces and sideslip angle with Mach number, time history, rudder effectiveness, and lateral oscillations are provided.

Memorandum presenting the results of measurements of gust and draft velocities within thunderstorms at an air field over a 7-day period. The data are summarized in tables and compared to previous flights.

From Summary: "Thrust augmentation of an axial-flow type turbojet engine by burning fuel in the tail pipe has been investigated in the NACA Cleveland altitude wind tunnel. The performance was determined over a range of simulated flight conditions and tail-pipe fuel flows. The engine tail pipe was modified for the investigation to reduce the gas velocity at the inlet of the tail-pipe combustion chamber and to provide an adequate seat for the flame; four such modifications were investigated."

From Summary: "The hottest part of a turbine blade is likely to be the trailing portion. When the blades are cooled and when water is used as the coolant, the cooling passages are placed as close as possible to the trailing edge in order to cool this portion. In some cases, however, the trailing portion of the blade is so narrow, for aerodynamic reasons, that water passages cannot be located very near the trailing edge. Because ceramic coatings offer the possibility of protection for the trailing part of such narrow blades, a theoretical study has been made of the cooling effect of a ceramic coating on: (1) the blade-metal temperature when the gas temperature is unchanged, and (2) the gas temperature when the metal temperature is unchanged."

The gust and draft velocities from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air FIeld, Ohio, from August 7, 1947 to August 13, 1947 are presented.

This report contains the results of the investigation of the aerodynamic characteristics of the flying mock-up of the Consolidated Vultee XP-92 airplane as conducted in the Ames 40- by 80-foot wind tunnel, Data are presented for test conditions which would give information as to the limits of stability and controllability, and also, the effect of Reynolds number. No analysis of the data has been made.

From Summary: "The performance of an annular combustion chamber from a 24C turbojet engine was investigated over a range of simulated altitudes from 20,000 to 55,000 feet and corrected engine rotor speeds from 6000 to 13,000 rpm at a simulated ram-pressure ratio of 1.04. The purpose of the investigation was to determine the effects on the altitude operational limits, combustor-outlet gas temperature distribution, combustion efficiencies, and combustor inlet-to-outlet total-pressure drops of two changes in the 24C-4B basket air-passage arrangements that were designed to improve combustor-outlet temperature distribution. These changes were: (a) replacement of the downstream secondary air holes with large rectangular slots further upstream (rectangular-slot basket), and (b) enlargement of anticoking holes in the rectangular-slot basket (modified rectangular-slot basket)."