The following report describes the process of epoxy resin casting of high-voltage transformers, bushings, and potheads.

"Design work was completed and construction initiated on a prototype field altimeter based on the gas density dependence of Townsend discharge current in an electrical discharge. The design of an ion tracer air velocity meter for laboratory applications, and construction of three units were successfully completed. Theoretical and experimental support is presented, showing the applicability of the ion tracer system to the accurate measurement of linear gas velocity. The operating range of the laboratory meter is 150 to 2500 ft/min at ambient pressures between 200 mu and 30.0 mm Hg. Further investigations on the application of the ion tracer concept to flowrate measurements are presented. By generating velocity profile curves with an ion tracer calibrated thermoanemometer, it was possible to determine the flowrate for 2 flow and pressure conditions; 37.5 cfm at 19.6 mm and 75 cfm at 9.8 mm Hg. Comparison with a calibrated Rotameter technique was within 5% in both cases. Also presented are some preliminary investigations leading to the development of a generalized ion tracer flowmeter for low gas densities. Results of some supplemental electrical discharge experiments in rarefied atmospheres are described. It was observed that electrical oscillations could be produced in a low density gas discharge, …

Considerable work has been done on decontamination procedures for both corrosion products and fission products. Testing of promising procedures under typical rupture conditions is an important phase of this work. The Irradiated Rupture Prototype (IRP) has been used since August in this evaluation work. This document is one of a series reporting these data.

The biological evaluation of the thermal neutron capture reaction of boron-10, B10 (n,α)Li7 + 2.786 MeV, has previously been studied, using different particles from the boron-10 thermal neutron capture reaction compared with 250 kvp x-rays has been reported as 1.05 for spleen-thymic weight reduction (1), as 1.5 to 2.0 for skin lesions in pigs (2), and 1.87 for skin lesions of the rabbit's ear (3). The significance of such a calculation is felt to be unreliable for the boron-10 reaction in animals because of the vagaries of dose determination resulting from irregular boron distribution, and by the presence of an adventitious irradiation from fast neutrons and capture gammas that is inadequately determined at present. Our present experiment attempts to circumvent the difficulties attendent to studies of the boron-10 reaction in animals by comparing the effect of this reaction on the proliferative capacity of HeLa cells with those produced with 250 kvp x-ray.

In these lectures we will discuss some examples of information about magnetic properties of solids which can be obtained by neutron scattering. We consider a scattering process in which a neutron with wave vector k and spin σ is incident upon a solid in state q>. (Here q stands for all of the quantum numbers which describe the state of the solid, such as spin and orbital electronic states, phonon numbers, etc.) After interacting with the solid, the neutron goes off with wave-vector k' and spin σ', leaving the solid in state q'>. In performing an experiment of this sort one does not usually observe the initial and final spin states of the neutron or the initial and final states of the solid. We must then sum over all possible final states and average over all initial states.

The present core of the Brookhaven Graphite Reactor consists of some 4900 highly enriched uranium fuel loaded in 615 horizontal fuel channels passing through a 25 foot cube of graphite moderator and reflector. The core is divided into two halves (north and south) by an 8 cm. wide vertical gap in the center of the graphite. The cooling air enters the reactor through inlet filters, at the rate of 270,000 CFM, passes into the central gap and flows bi-directionally through the north and south halves of the core. It then enters the collecting plenums and flows into the north and south ducts. The air is first monitored by the north and south exit air monitors located within the pile building. These are moving filter tape monitors with beta scintillation detectors. They are essentially operational monitors and are maintained by reactor operations. They are essentially operational monitors and are maintained by a reactor operations. The air then passes through the exit air filters, heat exchanger, venturi and on to the fan house where the north and south ducts join. After the fan house the air is monitored by Argon-41 by a Kanne ion chamber syste.

Boron-10 has a high thermal neutron capture cross section (3880 barns). Following neutron capture, the subsequent nuclear disintegration produces an alpha particle and a lithium-7 nucleus with the release of an average of 2.34 MeV for the particle irradiation, and in 93% of the reactions there is also the emission of an 0.48 MeV gamma ray: [equation not transcribed]. The kinetic energy is divided between the lithium-7 nucleus and the alpha particle giving the equal and opposite momentums with a range in tissue of about 8-14μ or approximately 1 cell diameter (1). This fact and the reported favorable partition of boron between tumor and the normal brain suggested a possible therapeutic usefulness which has been investigated clinically. The object of our study is to document the biological effects of the B10 (n,α) Li7 reaction on the brain of dogs injected with boron-10 30 minutes prior to irradiation with thermal neutrons. For this, we felt it desirable to estimate a dose for the boron-10 reaction which if exceeded, produces destruction of normal tissue. This dose could then be a reference dose to be utilized as a maximal limit for the irradiation of normal tissue. We have assured that the largest fluence …

A part of the development activities of the Process Equipment Development Group, Chemical Development, HLO through the year 1959 has consisted of test evaluation of some of the never products of manufacturers, design and refinement of novel units to do certain specialized jobs and development of improved components for existing plant equipment. Modification of present chemical processing methods and investigation of new basic procedures have made it necessary to utilize different and "exotic" materials, titanium, has given rise to another problem-- that of the selection of adequate and compatible bearings where the titanium is used as moving or rotating part.

Abstract: This technical report is concerned with the program and results of the SM-1 reactor vessel head removal and core inspection at Fort Belvoir, Virginia from the period March 7, 1969 to May 17, 1959. It covers the operating procedures in detail and records the conditions found and problems encountered in order to make a record for reference in future work of this nature. The major objective of the program, to obtain irradiation data on the SM-1 type core, has been met. The boron control rod elements were found unsatisfactory for full core life, and europium oxide elements were placed in the core for future irradiation stability data. A major problem was experienced with the cracked pressure vessel head studs. The methods developed for the removal of the broken studs are presented. The complete metallurgical study of the stud failure from stress corrosion is included as Appendix B.

This paper reports the chemical and physical properties of the NTA film packet. It correlates with these properties the response of this packet to neutrons of various energies. In this correlation the concept of the track unit is introduced as a basic unit for reporting film-packet response.

Abstract. While the concept of a biological system as a balanced network of chemical transformations is not a new one, experimental definition of specific systems has been lacking. This paper defines theoretically and experimentally a number of such networks and their behavior and response to some limited environmental changes.

"The degree of cleanliness is defined, and the methods and materials to be used are outlined for carbon and low alloy steels, 300 and 400 series ferritic and austenitic stainless steels, special Ni-Cr base heat-resistant hard-facing and high-temperature brazing alloys, and some non-ferrous materials."

The absorption in lead of Bremsstrahlung X radiation from a Sr^90 TiO3 pellet in the proximity of Hastelloy "C" was measured. The tenth value layer of the more energetic components of the X-ray continuum was determined to be 1.60 inches.