This report describes the analysis and modeling approaches used in the evaluation for criticality-control applications of the neutron-absorbing structural-amorphous metal (SAM) coatings. The applications of boron-containing high-performance corrosion-resistant material (HPCRM)--amorphous metal as the neutron-absorbing coatings to the metallic support structure can enhance criticality safety controls for spent nuclear fuel in baskets inside storage containers, transportation casks, and disposal containers. The use of these advanced iron-based, corrosion-resistant materials to prevent nuclear criticality in transportation, aging, and disposal containers would be extremely beneficial to the nuclear waste management programs.

Argentina is faced with the challenging problem ofdeveloping technology for near-surface disposal and isolation of low- andintermediate-level radioactive waste (LILW). The preferred option fordisposal of LILW (including both relatively short-lived and long-livedradionuclides) is to use disposal facilities that arenear-surface--either above or below ground level [IAEA, 1985; 2001a;2004]. How individual components of a waste disposal system perform(including waste forms, waste containers, engineered barriers and hostenvironment) will determine system safety and the safety of thesurrounding environment [IAEA, 1999]. The lack of appropriate engineeringfor the backfill, and for the selection of sealing and covering materialsfor trenches, vaults, and ditches, could result in the escape ofradionuclides from the disposed wastes [IAEA, 1994a; 2001b]. Therefore,assessment and design of backfill, barriers, and cover materials are veryimportant, both for preventing invasion of water into the disposalsystem, and for retarding radionuclides that could potentially migratefrom the system into the atmosphere or groundwater [IAEA, 1982; 1994b;2001a].

The Waste Calcining Facility (WCF) is located at the Idaho Nuclear Technology and Engineering Center. In 1998, the WCF was closed under an approved Hazardous Waste Management Act/Resource Conservation and Recovery Act (HWMA/RCRA) Closure Plan. Vessels and spaces were grouted and then covered with a concrete cap. The Idaho Department of Environmental Quality issued a final HWMA/RCRA post-closure permit on September 15, 2003, with an effective date of October 16, 2003. This permit sets forth procedural requirements for groundwater characterization and monitoring, maintenance, and inspections of the WCF to ensure continued protection of human health and the environment.

The synthesis and characterization of 1-10 nm Si nanocrystals highly resistant to oxidation is described. The nanocrystals were prepared by thermal decomposition of tetramethylsilane at 680 C, or in a gold- induced catalytic process at lower temperatures down to 400-450 C using trioctylamine as an initial solvent. Transmission electron microscopic analysis of samples obtained in the presence of gold show that the nanocrystals form via solid-phase epitaxial attachment of Si to the gold crystal lattice. The results of computational modeling performed using first principles density functional theory (DFT) calculations predict that the enhanced stability of nanocrystals to oxidation is due to the presence of N or N-containing groups on the surface of nanocrystals.

The electromagnetic particle-in-cell (PIC) code VORPAL is being used to simulate the interaction of microwave radiation through an electron cloud. The results so far showgood agreement with theory for simple cases. The study has been motivated by previous experimental work on this problem at the CERN SPS [1], experiments at the PEP-II Low Energy Ring (LER) at SLAC [4], and proposed experiments at the Fermilab Main Injector (MI). With experimental observation of quantities such as amplitude, phase and spectrum of the output microwave radiation and with support from simulations for different cloud densities and applied magnetic fields, this technique can prove to be a useful probe for assessing the presence as well as the densityof electron clouds.

Solid low-level radioactive wastes at the Savannah River Site (SRS) are disposed in trenches. In order to determine the permissible radioactive inventory limits for such disposal facilities, it is required to assess the behavior of radioactive waste material over long periods of time. The sensitivity of flow and I-129 (and similar radionuclides) transport in groundwater in the vadose zone to the hydraulic conductivities of the vadose zone subregions and the low-level waste is identified and quantified. A trench configuration and simulation model have been developed to analyze the flow and transport of the radionuclide in the vadose zone as it migrates to the groundwater table. The analysis identifies and quantifies the major dependencies of the flow and radionuclide fractional flux on the subregion hydraulic conductivities. Analysis results indicate the importance of the hydraulic conductivity assigned to the materials modeled, thereby providing the modeler and decision makers with valuable insights on the potential impact of the hydraulic conductivity on flow and radionuclide transport.

When a fixed anode x-ray tube is placed in a magnetic field (B) that is parallel to the anode-cathode axis, the x-ray exposure increases with increasing B. It was hypothesized that the increase was caused by backscattered electrons which were constrained by B and reaccelerated by the electric field onto the x-ray tube target. We performed computer simulations and physical experiments to study the behavior of the backscattered electrons in a magnetic field, and their effects on the radiation output, x-ray spectrum, and off-focal radiation. A Monte Carlo program (EGS4) was used to generate the combined energy and angular distribution of the backscattered electrons. The electron trajectories were traced and their landing locations back on the anode were calculated. Radiation emission from each point was modeled with published data (IPEM Report 78), and thus the exposure rate and x-ray spectrum with the contribution of backscattered electrons could be predicted. The point spread function for a pencil beam of electrons was generated and then convolved with the density map of primary electrons incident on the anode as simulated with a finite element program (Opera-3d, Vector Fields, UK). The total spatial distribution of x-ray emission could then be calculated. Simulations showed that …

Ecosystem health with its near infinite number of variables is difficult to measure, and there are many opinions as to which variables are most important, most easily measured, and most robust, Bioassessment avoids the controversy of choosing which physical and chemical parameters to measure because it uses responses of a community of organisms that integrate all aspects of the system in question. A variety of bioassessment methods have been successfully applied to aquatic ecosystems using fish and macroinvertebrate communities. Terrestrial biotic index methods are less developed than those for aquatic systems and we are seeking to address this problem here. This study had as its objective to examine the baseline differences in ant communities at different seral stages from clear cut back to mature pine plantation as a precursor to developing a bioassessment protocol. Comparative sampling was conducted at four seral stages; clearcut, 5 year, 15 year and mature pine plantation stands. Soil and vegetation data were collected at each site. All ants collected were preserved in 70% ethyl alcohol and identified to genus. Analysis of the ant data indicates that ants respond strongly to the habitat changes that accompany ecological succession in managed pine forests and that individual genera …

Simulation of ductile fracture at the atomic scale reveals many aspects of the fracture process including specific mechanisms associated with void nucleation and growth as a precursor to fracture and the plastic deformation of the material surrounding the voids and cracks. Recently we have studied void coalescence in ductile metals using large-scale atomistic and continuum simulations. Here we review that work and present some related investigations. The atomistic simulations involve three-dimensional strain-controlled multi-million atom molecular dynamics simulations of copper. The correlated growth of two voids during the coalescence process leading to fracture is investigated, both in terms of its onset and the ensuing dynamical interactions. Void interactions are quantified through the rate of reduction of the distance between the voids, through the correlated directional growth of the voids, and through correlated shape evolution of the voids. The critical inter-void ligament distance marking the onset of coalescence is shown to be approximately one void radius based on the quantification measurements used, independent of the initial separation distance between the voids and the strain-rate of the expansion of the system. No pronounced shear flow is found in the coalescence process. We also discuss a technique for optimizing the calculation of fine-scale information …

A vitrification technology utilizing a lanthanide borosilicate (LaBS) glass appears to be a viable option for dispositioning excess weapons-useable plutonium that is not suitable for processing into mixed oxide (MOX) fuel. A significant effort to develop a glass formulation and vitrification process to immobilize plutonium was completed in the mid-1990s to support the Plutonium Immobilization Program (PIP). Further refinement of the vitrification process was accomplished as part of the Am/Cm solution vitrification project. The LaBS glass formulation was found to be capable of immobilizing in excess of 10 wt% Pu and to be very tolerant of the impurities accompanying the plutonium material streams. Thus, this waste form would be suitable for dispositioning plutonium owned by the Department of Energy-Office of Environmental Management (DOE-EM) that may not be well characterized and may contain high levels of impurities. The can-in-canister technology demonstrated in the PIP could be utilized to dispose of the vitrified plutonium in the federal radioactive waste repository. The can-in-canister technology involves placing small cans of the immobilized Pu form into a high level waste (HLW) glass canister fitted with a rack to hold the cans and then filling the canister with HLW glass. Testing was completed to demonstrate that …

We report the discovery of a self-doped multilayer high T{sub c} superconductor Ba{sub 2}Ca{sub 3}Cu{sub 4}O{sub 8}F{sub 2} (F0234) which contains distinctly different superconducting gap magnitudes along its two Fermi-surface sheets. While formal valence counting would imply this material to be an undoped insulator, it is a self-doped superconductor with a T{sub c} of 60 K, possessing simultaneously both electron- and hole-doped Fermi-surface sheets. Intriguingly, the Fermi-surface sheet characterized by the much larger gap is the electron-doped one, which has a shape disfavoring two electronic features considered to be important for the pairing mechanism: the van Hove singularity and the antiferromagnetic ({pi}/{alpha}, {pi}/{alpha}) scattering.

We discuss images of the central {approx} 10 kpc (in projection) of the galaxy merger NGC 6240 at H and K{prime} bands, taken with the NIRC2 narrow camera on Keck II using natural guide star adaptive optics. We detect 28 star clusters in the NIRC2 images, of which only 7 can be seen in the similar-spatial-resolution, archival WFPC2 Planetary Camera data at either B or I bands. Combining the NIRC2 narrow camera pointings with wider NICMOS NIC2 images taken with the F110W, F160W, and F222M filters, we identify a total of 32 clusters that are detected in at least one of these 5 infrared ({lambda}{sub c} > 1 {micro}m) bandpasses. By comparing to instantaneous burst, stellar population synthesis models (Bruzual & Charlot 2003), we estimate that most of the clusters are consistent with being {approx} 15 Myr old and have photometric masses ranging from 7 x 10{sup 5} M{sub {circle_dot}} to 4 x 10{sup 7}M{sub {circle_dot}}. The total contribution to the star formation rate (SFR) from these clusters is approximately 10M{sub {circle_dot}} yr{sup -1}, or {approx} 10% of the total SFR in the nuclear region. We use these newly discovered clusters to estimate the extinction toward NGC 6240's double nuclei, …

The accurate computation of the external magnetic field from a permanent magnet motor is accomplished by first computing its magnetic scalar potential. In order to find a solution which is valid for any arbitrary point external to the motor, a number of proven methods have been employed. Firstly, A finite element model is developed which helps generate magnetic scalar potential values valid for points close to and outside the motor. Secondly, charge simulation is employed which generates an equivalent magnetic charge matrix. Finally, an equivalent multipole expansion is developed through the application of a toroidal harmonic expansion. This expansion yields the harmonic components of the external magnetic scalar potential which can be used to compute the magnetic field at any point outside the motor.

As part of its national security mission, Lawrence Livermore develops technologies to help government agencies prevent terrorists from smuggling nuclear materials into the country. One ongoing effort is to design radiation detectors that can distinguish threat sources from legitimate sources, such as medical isotopes, and naturally occurring radiation. (See S&TR, September 2004, pp. 4-11; May 2006, pp. 4-10.) Detectors intended for use by nonspecialists must be easy to operate and require minimal maintenance. To be most effective, they also must detect both gamma and neutron energies. That may sound like a lot to ask of one instrument, but the Ultrahigh-Resolution Gamma and Neutron Spectrometer (UltraSpec) delivers all of these features. UltraSpec is so sensitive that even the minute thermal energy deposited by a single gamma ray or neutron can be detected with high precision. With this capability, the detector can identify differences in composition that help reveal a material's origin, processing history, and likely intended use. In addition to its application as a counterterrorism technology, UltraSpec can be used to protect nuclear material stored at nuclear power plants, to evaluate weapon stockpiles, and to verify material composition. UltraSpec was developed by a team of scientists and engineers from Livermore's Physics …

Space charge and coherent synchrotron radiation may deteriorate electron beam quality when the beam passes through a magnetic bunch compressor. This paper presents the transverse phase-space tomographic measurements for a compressed beam at 60 MeV, around which energy the first stage of magnetic bunch compression takes place in most advanced linacs. Transverse phase-space bifurcation of a compressed beam is observed at that energy, but the degree of the space charge-induced bifurcation is appreciably lower than the one observed at 12 MeV.

People with flu-like symptoms who seek treatment at a medical clinic or hospital often must wait several hours before being examined, possibly exposing many people to an infectious virus. If a patient appears to need more than the routine fluids-and-rest prescription, effective diagnosis requires tests that must be sent to a laboratory. Hours or days may pass before results are available to the doctor, who in the meantime must make an educated guess about the patient's illness. The lengthy diagnostic process places a heavy burden on medical laboratories and can result in improper use of antibiotics or a costly hospital stay. A faster testing method may soon be available. An assay developed by a team of Livermore scientists can diagnose influenza and other respiratory viruses in about two hours once a sample has been taken. Unlike other systems that operate this quickly, the new device, called FluIDx (and pronounced ''fluidics''), can differentiate five types of respiratory viruses, including influenza. FluIDx can analyze samples at the point of patient care--in hospital emergency departments and clinics--allowing medical providers to quickly determine how best to treat a patient, saving time and potentially thousands of dollars per patient. The FluIDx project, which is led …

The Department of Energy Office of Environmental Management (DOE/EM) plans to conduct the Plutonium Disposition Project at the Savannah River Site (SRS) in Aiken, SC, to disposition excess weapons-usable plutonium. A plutonium glass waste form is a leading candidate for immobilization of the plutonium for subsequent disposition in a geologic repository. The objectives of this present task were to fabricate plutonium-loaded lanthanide borosilicate (LaBS) Frit B glass and perform testing to provide near-term data that will increase confidence that LaBS glass product is suitable for disposal in the proposed Federal Repository. Specifically, testing was conducted in an effort to provide data to Yucca Mountain Project (YMP) personnel for use in performance assessment calculations. Plutonium containing LaBS glass with the Frit B composition with a 9.5 wt% PuO{sub 2} loading was prepared for testing. Glass was prepared to support glass durability testing via the ASTM Product Consistency Testing (PCT) at Savannah River National Laboratory (SRNL). The glass was characterized with X-ray diffraction (XRD) and scanning electron microscopy coupled with energy dispersive spectroscopy (SEM/EDS) prior to performance testing. This characterization revealed some crystalline PuO{sub 2} inclusions with disk-like morphology present in the as fabricated, quench-cooled glass. A series of PCTs was conducted …

Experiments at the FLASH facility at DESY have demonstrated that the higher order modes induced in superconducting cavities can be used to provide a variety of beam and cavity diagnostics. The axes of the modes can be determined from the beam orbit that produces minimum power in the dipole HOM modes. The phase and amplitude of the dipole modes can be used to obtain high resolution beam position information, and the phase of the monopole modes to measure the beam phase relative to the accelerator rf. For most superconducting accelerators, the existing higher order mode couplers provide the necessary signals, and the downmix and digitizing electronics are straightforward, similar to those for a conventional beam position monitor.

A new laser-wire (LW) system has been installed at the ATF extraction line at KEK, Tsukuba. The system aims at a micron-scale laser spot size and employs a mode-locked laser system. The purpose-built interaction chamber, light delivery optics, and lens systems are described, and the first results are presented.

None

This research program has explored the stability of alloys under pulsed laser irradiation. Two primary directions were investigated: (i) phase transitions during a single laser pulse, and (ii) phase stability under repeated laser irradiation. The first theme was primarily concerned with both the crystalline to amorphous phase transition and the transition of liquids and glasses to crystalline matter. The second project examined the phase evolution during laser pulsing in situations where plastic deformation was prevalent (high-energy laser pulses). Both computer simulation and experimental programs were undertaken. Our work using computer simulations had several notable successes. For the work connected with multiple pulsing, we used molecular dynamics (MD) to simulate the behavior of alloys under severe plastic deformation. We found that during high strain-rate deformation atomic mixing of chemical species is random, independent of the detailed thermochemical properties of the system. This result contrasts with recent reports. In this work, we also developed two new methods of analyzing atomic mixing, one is based on relative mean square displacements (RMSD) of atoms and the other, Burgers vector analysis (BVA), on nearest neighbor displacements. The RMSD analysis is valuable in that it specifies the length scales over which deformation processes take place, and …

We report the first experimental observation of sequential, multiple polymorphic phase transformations occurring in Praseodymium dynamically compressed using a ramp wave. The experiments also display the signatures of reverse transformations occuring upon pressure release and reveal the presence of small hysteresys loops. The results are in very good agreement with equilibrium hydrodynamic calculations performed using a thermodynamically consistent, multi-phase equation of state for Praseodymium, suggesting a near-equilibrium transformation behavior.

The cosmic microwave background power spectra are studied for different families of single field new and chaotic inflation models in the effective field theory approach to inflation. We implement a systematic expansion in 1/N(e), where N(e)~;;50 is the number of e-folds before the end of inflation. We study the dependence of the observables (n(s), r and dn(s)/dlnk) on the degree of the potential (2n) and confront them to the WMAP3 and large scale structure data: This shows in general that fourth degree potentials (n=2) provide the best fit to the data; the window of consistency with the WMAP3 and LSS data narrows for growing n. New inflation yields a good fit to the r and n(s) data in a wide range of field and parameter space. Small field inflation yields r<0.16 while large field inflation yields r>0.16 (for N(e)=50). All members of the new inflation family predict a small but negative running -4(n+1) x 10-4<=dn(s)/dlnk<=-2 x 10-4. (The values of r, n(s), dn(s)/dlnk for arbitrary N(e) follow by a simple rescaling from the N(e)=50 values.) A reconstruction program is carried out suggesting quite generally that for n(s) consistent with the WMAP3 and LSS data and r<0.1 the symmetry breaking scale …

We perform an analysis of the production of elements with mass number A {ge} 12 in a standard Big Bang Nucleosynthesis scenario. The goal is to provide a more accurate estimate of the very low and yet poorly explored abundance of such elements, relevant for the pristine Population III stars. We examine the synthesis channels for these elements in a critically revised and updated version of the Wagoner-Kawano code, as well as in a further enlarged version including four additional nuclides and a significantly extended nuclear network. Our results show no major discrepancies with the ones obtained using a smaller nuclear network. The robustness of the standard predictions--the early generation of star developed in a metal-free environment--is confirmed.