Abstract: "Creep and creep-rupture tests were made on 25-O aluminum sheet at temperatures of 500 and 550 C. The estimated stresses that will produce 0.5 per cent deformation and rupture in 10,000 hours at 400, 450, 500, and 550 C (data at 400 and 450 C are from BMI-T-29, dated June 9, 1950) are presented."

Summary: "The laboratory data collected during the metallurgical evaluation of these rods indicate that lower rolling temperatures increased the ultimate and yield strength, the amount of cold work, and the degree of preferred orientation existing in these uranium rods."

Abstract: "A batch of slugs is being prepared for which the U-235 content will be 1.75 per cent, and it is of interest to calculate the minimum number of such slugs required for a critical assembly in water. Using Handbook (CL-697) methods, a critical assembly of these slugs arranged in a lattice with a spacing of 5.5 cm."

This report describes a completed counter experiment to measure the attenuation of K+ mesons in various materials.

A exploratory study was made of a polarographic technique in which an alternating sine or square-wave potential is superimposed upon the applied d.c. potential of the polarographic scan. Recording of the a.c. component of the polarographic current results in derivative-type waves. It was shown that the technique yields greater sensitivity and greater selectivity than normal polarographic technique.

Summary: The Regnault Method as applied to tritium purity determinations is described. The operating difficulties, such as temperature and humidity changes, static charges, excessive vibrations, contamination with air and helium, etc., and the methods currently in use for minimizing such difficulties, are discussed. A discussion of ion-chamber calibrations, and the correlation of ion-chamber results with Regnault Method results, are included. A precision of ±1% has been obtained, but the accuracy is not yet known.

A pile gas leak detection system consisting of a purchased mass spectrographic type of helium detector, a long sampling line for use in remote or relatively inaccessable locations, a pump to pull a continuous sample of gas from the tip of the probe to the detector, and a rotameter to measure the gas flow rate in the sampling line has been developed, calibrated, operationally tested. The system is practical for use in locating all pile gas leaks larger than about 0.1 cubic foot per hour.

Abstract: The counting accuracy of the Chicago Scalers, Models 961A and 961B, is a function of the bias setting of the limiter (V2). this report gives quantitative data supporting this thesis. A method of making bias settings is suggested. These tests were run at the suggestion of Mr. V. C. Hanson.

Abstract: Pure UO2F2 is made by reaction between anhydrous HF and pure UO3. Although it is difficult to prepare free of water, it is not very hygroscopic. Prolonged heating at 100-105 degrees releases 99.9% of the water in an aqueous solution; the rate of loss of water is very small after saturation is reached. X-ray diffraction data give a density of 6.2 for the solid. The density of a 1.004 M solution is 1.274; the density of a saturated solution (5.130 M) is 2.400. The densities of F-9 solutions have been calculated from the densities of ordinary aqueous solutions, and the values are compared graphically. Data on the solubility indicate that there is a small increase in the range 25-100 degrees. Recovery of pure F-9 from a solution is hampered by hydrolysis of U)2F2 to give HF. The HF may be held back by addition of UO3 or CaO; the use of the latter, however, makes more difficult the recovery of all the F-9. Molar conductivities of UO2F2 solutions at 25 degrees, as well as the specific conductivities of a 1 molar solution containing various concentrations of UO3, have been determined. The addition of UO3 lowers the conductivity. The low …

An annual report is given on the operation and costs of waste-disposal facilities at ORNL laboratories and operating buildings in the Bethel Valley area. The operations of the hot-chemical and metal-waste systems, the process-waste system, and the radioactive-gas-disposal system which utilized the 250-ft stack located in the Radioisotope area are discussed. The miscellaneous operations which include the SS (source and special nuclear) material control, SS material recovery, off-shift service for research divisions, water demineralization plant operations, and hydrogen liquefaction are included. However, the disposal of cooling water from LITR, off-gases from the Hot Pilot Plant, and the ORNL Graphite Reactor building are not covered by the report.