An accurate Mark I /sup 1///sub 5/-scale, boiling water reactor (BWR), pressure suppression facility was designed and constructed at Lawrence Livermore Laboratory (LLL) in 11 months. Twenty-seven air tests using the facility are described. Cost was minimized by utilizing equipment borrowed from other LLL programs. The total value of borrowed equipment exceeded the program's budget of $2,020,000. Substantial flexibility in the facility was used to permit independent variation in the drywell pressure-time history, initial pressure in the drywell and toroidal wetwells, initial toroidal wetwell water level and downcomer length, vent line flow resistance, and vent line flow asymmetry. The two- and three-dimensional sectors of the toroidal wetwell provided significant data.

Test procedures to be used to demonstrate the temperature control function, flow control function, and transient response of the Mechanical Flow-Temperature Control Valve in the Kilowatt Isotope Power System are described in detail. (LCL)

We have constructed a quadrupole-mass filter system to measure the equilibrium constants and rates of reaction of the ..beta..-particle-induced exchanges between H/sub 2/, D/sub 2/, and T/sub 2/ at cryogenic temperatures. Even with careful calibration experiments at 25.4/sup 0/C, we could not completely remove the mass discrimination inherent in our method. We estimate the accuracy of our mixture analyses to be +-2.2% in the D/sub 2/-DT-T/sub 2/ system, and +-9% in the H/sub 2/-HT-T/sub 2/ system. Preliminary kinetic experiments showed that the time to reach equilibrium in the exchange H/sub 2/ + T/sub 2/ = 2HT is 7 to 14 h. The equivalent time interval in the exchange D/sub 2/ + T/sub 2/ = 2DT is 3 to 7 h. This measured isotope effect of two can be used to predict the rates of the DT exchange from the HT rates in the literature.

The Battelle Northwest Liquid Level Probe was evaluated for possible use in the LOFT Blowdown Suppression Tank. The results from the test indicate that the probe will measure the liquid level to +-/sup 1///sub 4/ inch, over a range of 50 inches. The next step is to test the functionability of the probe under simulated LOFT-Blowdown Suppression Tank operating conditions.

Trade-off studies of Near Term Hybrid Vehicle (NTHV) design elements were performed to identify the most promising design concept in terms of achievable petroleum savings. The activities in these studies are described. The results are presented as preliminary NTHV body design, expected fuel consumption as a function of vehicle speed, engine requirements, battery requirements, and vehicle reliability and cost. (LCL)

This review contains 175 references to commonly encountered dissolution problems.

A review of the LOFT Primary Coolant Pump Inlet Nozzle Thermal Analysis was conducted to satisfy the ASME code requirement that all analyses of Class I components be independently reviewed.

A valve for damping out flow surges in a vacuum system is described. The surge-damping mechanism consists of a slotted, spring-loaded disk adjacent to the valve's vacuum port (the flow passage to the vacuum roughing pump). Under flow surge conditions, the differential pressure forces the disk into a sealing engagement with the vacuum port, thereby restricting the gas flow path to narrow slots in the disk's periphery. The increased flow damps out the flow surge. When pressure is equalized on both sides of the valve, the spring load moves the disk away from the port to restore full flow conductance through the valve.

The Safety Analysis Report for Packaging (SARP) satisfies the request of the U.S. Energy Research and Development Administration for a formal safety analysis of the insulated drum shipping container identified as USA/9506/BLF(DOE-A1). Included are discussions of structural integrity, thermal resistance, radiation shielding and radiological safety, nuclear criticality safety, and quality control. Complete physical and technical descriptions of the packages are presented.

Raman and ESR measurements were used to study the atomic bonding and defect concentrations. Features are identified in the Raman spectra which can be attributed to configurations containing Si-Si, Si-As and As-As bonds. Features due to all three of these configurations were found to simultaneously exist, thus excluding a chemically ordered model of the bonding. However, the composition dependences of the features do not follow exactly a random bonding model either. The H bonding configurations were reflected in features at approx.2000 cm/sup -1/ in the Raman spectra. It was found that the H bonding changed dramatically in the As doping to 5% As alloying region. The ESR measurements indicated a low level of singly occupied defect states in all the samples studied.

Recent studies have shown straightforward systematic behavior as a function of constant proton and neutron number for neutron-induced fission cross sections of the actinide elements in the incident-neutron energy range 3 to 5 MeV. In this report, the second in a series, fission cross-section values are studied over the MeV incident-neutron energy range, and at 0.0253 eV. Fission-barrier heights and neutron-binding energies are correlated by constant proton and neutron number; however, these systematic behaviors alone do not explain the trends observed in the fission cross-section values.

This appendix to the final report on the Hybrid Passenger Vehicle Development Program contans data on Na-S batteries, Ni-Zn batteries; vehicle body design; tire characteristics; and results of computer simulations of vehicle yaw, pitch, and roll under various driving and aerodynamic conditions. (LCL)

None

None

An analysis to establish whether or not a leak-before-break concept would apply to the LOFT lower plenum injection nozzle is described. The analysis encompassed the structure from the inlet side of valve V-2170 to the lower plenum nozzle-to-reactor vessel weld on the left side of the emergency core cooling system (ECCS). The defect that was assumed to exist was of such a size that the probability of its being missed by the applicable inspection technique was near zero. The Inconel 600 nozzle forging with an initial assumed defect size of 0.64 cm (0.25 in.) deep would behave as follows: (1) the axially oriented defect would result in leak before rupture (the number of cycles to rupture was 11,000), (2) the circumferentially oriented defect would result in a rupture before leak. The number of cycles to failure would be in excess of 14,000. Based on the conservative assumption that the thermal stresses were membrane stresses as opposed to a bending stress, the following were found. For the Inconel 82 weld metal (thickness of 1.3 cm (0.53 in.)) and AISI 316 SST valve body, with an initial assumed defect of 0.25 cm (0.1 in.), the crack would grow through the thickness in …

The unique characteristics of the energy situation in developing countries imposes a unique set of requirements on analytical techniques used for energy planning. The urgency of the situation requires the rapid development and use of simplified models which make maximum use of available data but which can reflect the international energy context. Those techniques must also be able to deal with central energy/development issues such as energy equity or the energy implication of social equity policies, centralized vs. decentralized development, and urbanization.

Three types of thermonuclear fusion devices currently under development are reviewed for an electric utilities management audience. Overall design features of laser fusion, tokamak, and magnetic mirror type reactors are described and illustrated. Thrusts and trends in current research on these devices that promise to improve performance are briefly reviewed. Twenty photographs and drawings are included. (RME)

A linear-induction-motor drive system to position machine tool slides has been developed on a test bed that utilizes an air-bearing slide, laser interferometer feedback, and a microprocessor-based servo system. Static and dynamic positioning accuracies of +-16 nm (+-0.6 ..mu..in) have been demonstrated.

The preferential acceleration and resulting cosmic ray abundance enhancements of heavy elements (relative to protons) are calculated in the collisionless supernova shock acceleration model described by Eichler in earlier work. Rapidly increasing enhancements up to several tens times solar ratios are obtained as a function of atomic weight over charge at the time of acceleration. For material typical of hot phase interstellar medium, good agreement is obtained with the observed abundance enhancements.

The program ATOMLLL draws color, shaded, hidden-surface pictures and movies of ball-and-stick and space-filling molecular models. From a file containing the colors and radii of the atoms, the coordinates of their centers, and the descriptions of bonds, if any, the program computes the visible portions of each atom. ATOMLLL then writes their descriptions into a file that can be copied to tape. The tape is read by a Varian minicomputer, which controls the plotting on the Dicomed D-48 color-film recorder. 1 reference.

Objective of the evaluation is to evaluate the effectiveness of the electrostatic prefilter in prolonging the life of HEPA (high-efficiency particulate-air) filters. The theory of the electrostatic filter is reviewed, and Glove Box Number 046 is described in detail, followed by a description of the electrostatic prefilter used in the present application. Engineering drawings of the electrostatic prefilter are included. The procedure for evaluating the electrostatic prefilter includes the steps for conducting five different tests: evaluating (1) the HEPA filter alone, (2 and 3) the HEPA filter with a standard prefilter treated both as disposable and reusable, and (4 and 5) the HEPA filter with the electrostatic prefilter, again treated as disposable and reusable. Procedures for flowmeter calibrations and measurements of particle-size distributions are also included. Long-term maintenence of the system during the evaluation program is outlined, and estimates of component durability are given. An electrical engineering safety note describes the high-voltage operational hazard of the electrostatic prefilter and the testing of safety devices (the current-overload trip circuit, the filter-door-interlock system, and the current-limiting resistor).

The stress analysis performed on the 1''-PCC-76-A piping system inside containment penetration S-1A is described. Deadweight, thermal expansion, and seismic loads were considered. Results of this analysis show that the subject piping system will meet ASME Boiler and Pressure Vessel Code, Section III, Class 2 requirements provided that supports S8 and S9 are installed as recommended.

Specifications for casting the centerbody housing of the vulcan heater are provided. CD-4MCu steel has been specified for the centerbody and the properties of the steel are given. (FS)

The Lawrence Livermore Laboratory is involved in a program to produce energy by the laser-induced fusion of microtargets. These laser systems have become very large and powerful. In Shiva, the amplifier rods common to smaller systems have been replaced with an array of large elliptical amplifier discs with major axes as large as 42 cm. Under the high power levels of these devices it is imperative that the optical surfaces remain scrupulously clean. All units are therefore cleaned, assembled, and operated under clean room conditions. In spite of such precautions, persistent problems arise. These can be grouped into three categories: (1) the appearance of unknown contaminants from unknown sources, (2) the transfer of material from one part of the assembly to another, and (3) laser beam damage to the optical surfaces. Theses problems and their resolution by surface analytical methods are discussed. In addition some unique problems associated with the very large sample sizes are described.