"A 1/12-scale model of a horizontal tail of a fighter airplane was tested through the transonic speeds in the high-speed flow over an airplane wing, the surface of which served as a reflection plane for the model. Measurements of lift, elevator-hinge moment, angle of attack, and elevator angle were made in the Mach number range from 0.75 to 1.04 for elevator deflections ranging from 10 degrees to minus 10 degrees, and for angles of attack of minus 1.2 degrees, 0.4 degrees, and 3.4 degrees. The equipment used to measure the hinge moments of the model proved to be unsatisfactory, and for this reason the hinge-moment data are considered to be only qualitative" (p. 1).

"The static longitudinal stability characteristics of a 0.15-scale model of the Hermes A-lE2 missile have been determined in the Langley high-speed 7- by 10-foot tunnel over a Mach number range of 0.50 to 0.98, corresponding to Reynolds numbers, based on body length, of 12.3 x 10(exp 6) to 17.1 x 10(exp 6). This paper presents results obtained with body alone and body-fins combinations at 0 degrees (one set of fins vertical and the other set horizontal) and 45 degree angle of roll. The results indicate that the addition of the fins to the body insures static longitudinal stability and provides essentially linear variations of the lift and pitching moment at small angles of attack throughout the Mach number range" (p. 1).

From Summary: "An analysis is given of the oscillating motion of a ballistic missile which upon entering the atmosphere is angularly misaligned with respect to the flight path. The history of the motion for some example missiles is discussed from the point of view of the effect of the motion on the aerodynamic heating and loading. The miss distance at the target due to misalignment and to small accidental trim angles is treated. The stability problem is also discussed for the case where the missile is tumbling prior to atmospheric entry."

Report presenting information regarding transient oscillations observed in response to elevator pulses of the Douglas D-558-I airplane at a range of Mach numbers and altitudes. An application of the Fourier transform was used to obtain the frequency-response characteristics. The effects of lift coefficient on the frequency response are also included.

"Results are presented of a free-flight investigation between Mach numbers of 0.7 to 1.3 and Reynolds numbers of 3.1 x 10(exp 6) to 7.0 x 10(exp 6) to determine the longitudinal aerodynamic characteristics of the Northrop MX-775A missile. This missile has a wing, body, and vertical tail, but has no horizontal tail. The basic wing plan form has an aspect ratio of 5.5, 45 deg of sweepback of the 0.406 streamwise chord line, and a taper ratio of 0.4" (p. 1).

Memorandum presenting results of a free-flight investigation over a range of Mach and Reynolds numbers to determine the longitudinal aerodynamic characteristics of the Northrop MX-775A missile. The missile has a wing, body, and vertical tail, but has no horizontal tail. Results regarding basic data, drag, trim, lift and static stability, damping, and static pressure are provided.

Report presenting an investigation in the propeller-research tunnel to develop wing-leading-edge inlets for locations between the inboard and outboard nacelles on each wing of a four-engine airplane. Testing was performed on the basic wing and original inlet as well as NACA-developed inlets for two versions of the airplane.

In connection with the general problem of providing air flow to an aircraft power plant located within a fuselage, an investigation was conducted in the Langley 8-foot high-speed tunnel to determine the effect on external drag and pressure distribution of air inlet openings located at the nose of a streamline body. Air outlet openings located at the tail and at the 21-percent and 63-percent stations of the body were also investigated. Boundary layer transition measurements were made and correlated with the force and the pressure data. Individual openings were investigated with the aid of a blower and then practicable combinations of inlet and outlet openings were tested. Various modifications to the internal duct shape near the inlet opening and the aerodynamic effects of a simulated gun in the duct were also studied. The results of the tests suggested that outlet openings should be designed so that the static pressure of the internal flow at the outlet would be the same as the static pressure of the external flow in the vicinity of the opening.

Report presenting an investigation conducted to determine the overall performance of the J73 two-stage turbine with a standard rotor-blade configuration. The turbine operated with a maximum brake internal efficiency between 0.91 and 0.92 at an overall pressure ratio of about 3.4 and 120 percent equivalent design rotor speed. Results regarding the overall performance, variation of equivalent weight flow with overall pressure ratio, and effect of limiting blade loading are provided.

A set of propeller operating efficiency charts, based on a coefficient from which the propeller rotational speed has been eliminated, is presented. These charts were prepared with data obtained from tests of full-size metal propellers in the NACA propeller-research tunnel. Working charts for nine propeller-body combinations are presented, including results from tests of dual-rotating propellers. These charts are to be used in the calculation of the range and the endurance of airplanes equipped with constant-speed propellers in which, for given flight conditions, it is desired to determine the propeller revolution speed that gives the maximum ratio of the propulsive efficiency to the specific fuel consumption. The coefficient on which the charts are based may be written in the form of a thrust coefficient or a thrust-power coefficient. A method of using the charts is outlined and sample computations for a typical airplane are included.

Report discussing various features of the stability of ballistic reentry shapes, including considerations for ballistic-missile and manned-satellite reentry capsules. Attainment of satisfactory stability of reentry bodies with subsonic terminal velocities was not found to be too difficult, but undesirable features that may cause marginal stability characteristics may be introduced in an effort to minimize weight. Reentry bodies with supersonic terminal velocities have fewer stability issues.

"An analytic method for the design of automatic controls is developed that starts from certain arbitrary criterions on the behavior of the controlled system and gives those physically realizable equations that the control system can follow in order to realize this behavior. The criterions used are developed in the form of certain time integrals. General results are shown for systems of second order and of any number of degrees of freedom. Detailed examples for several cases in the control of a turbojet engine are presented" (p. 207).

"A preliminary analytical investigation was made to determine the feasibility of the basic idea of controlled failure points as safety valves for the primary airplane structure. The present analysis considers the possibilities of the breakable wing tip which, in failing as a weak link, would relieve the bending moments on the wing structure. The analysis was carried out by computing the time histories of the wing and stabilizer angle of attack in a 10g pull-up for an XF8F airplane with tips fixed and comparing the results with those for the same maneuver, that is, elevator motion but with tips jettisoned at 8g" (p. 1).

A preliminary investigation was conducted to determine the combustion characteristics of a fuel composed of 50 percent pentaborane and 50 percent JP-4 (MIL-F-5624A) by weight in a turbojet combustor. A combustor designed to fit the housing of a J33-A-23 turbojet engine was selected for convenience. The fuel was evaluated at two engine conditions simulating altitudes of 40,000 and 57,000 feet, an engine speed of 85 percent of rated rpm, and a flight Mach number of 0.6. The pentaborane blend was initially evaluated in combustors developed for pure pentaborane and diborane reported in NACA RM E53B18 and RM E52L15. The performance of the blend was unsatisfactory in these combustors. A new combustor was then developed which provided combustor efficiencies measured from 91 to 101 percent as compared with efficiencies of 92 to 94 percent previously obtained for pentaborane at comparable conditions. Additional refinements of design details are needed to obtain lower oxide deposits and a more uniform outlet temperature profile; however, the combustor is believed to incorporate some of the design principles required to obtain satisfactory over-all performance with the fuel blend investigated.

Report presenting an investigation at a free-stream Mach number of 1.80 in a blowdown tunnel to study the effect on the pressure distribution of a zero-angle-of-attack wing surface when certain exhaust parameters of a hot turbojet engine are varied. Results regarding shock wave and pressure coefficients are provided.

Report presenting an investigation of the maximum hovering time, or the time that a helicopter can sustain itself without motion, for helicopters using a reciprocating engine, by ramjet engines at the tips of rotor blades, and by pulse-jet engines at the tips of rotor blades. Testing showed that the reciprocating engine permitted much longer hovering time than the jet-propulsion engines, but the jet-propulsion engines were much lighter and could lift greater disposable loads.

"An analysis was developed for calculating the radial temperature distribution in a gas turbine with only the temperatures of the gas and the cooling air and the surface heat-transfer coefficient known. This analysis was applied to determine the temperatures of a complete wheel of a conventional single-stage impulse exhaust-gas turbine. The temperatures were first calculated for the case of the turbine operating at design conditions of speed, gas flow, etc. and with only the customary cooling arising from exposure of the outer blade flange and one face of the rotor to the air" (p. 1).

An equation for average heat transfer of a surface was derived when the boundary layer changed from laminar to turbulent. Influences on the heat transfer through a laminar boundary layer of Mach number, temperature ratio (gas temperature divided by wall temperature), and exponents of gas-property temperature relations were shown to be relatively small for air with Mach numbers less than 2 and temperature ratios between 1 and 4. Good agreement was obtained with experimental results from cylinders, an airfoil, and turbine blades.

Analytical methods are presented for the determination of local values of outside and inside heat-transfer coefficients and effective gas temperatures by use of turbine-blade-temperature measurements. The methods are derived for a number of configurations that can be applied to typical cooled-turbine-blade shapes as well as to other types of heat-transfer apparatus.

A theoretical analysis of the radial temperature distribution through the rotor and constant cross sectional area blades near the coolant passages of liquid cooled gas turbines was made. The analysis was applied to obtain the rotor and blade temperatures of a specific turbine using a gas flow of 55 pounds per second, a coolant flow of 6.42 pounds per second, and an average coolant temperature of 200 degrees F. The effect of using kerosene, water, and ethylene glycol was determined. The effect of varying blade length and coolant passage lengths with water as the coolant was also determined. The effective gas temperature was varied from 2000 degrees to 5000 degrees F in each investigation.

From Summary: "A knock-limited performance investigation was conducted on blends of triptane and 28-P fuel with a 12-cylinder, V-type, liquid-cooled aircraft engine of 1710-cubic-inch displacement at three compression ratios: 6.65, 7.93, and 9.68. At each compression ratio, the effect of changes in temperature of the inlet air to the auxiliary-stage supercharger and in fuel-air ratio were investigated at engine speeds of 2280 and. 3000 rpm. The results show that knock-limited engine performance, as improved by the use of triptane, allowed operation at both take-off and cruising power at a compression ratio of 9.68."

Report presenting an investigation of the design characteristics and loadings conducive to the tumbling of airplanes with no horizontal tails. Empirical design requirements based on model testings of 18 different configurations and an explanation of the phenomena of tumbling are provided.

"Paper presents a practical method for computing the approximate values of the normal component of the induced velocity at points in the flow field of a lifting rotor. Tables and graphs of the relative magnitudes of the normal component of the induced velocity are given for selected points in the longitudinal plane of symmetry of the rotor and on the lateral rotor axis. A method is also presented for utilizing the tables and graphs to determine the interference induced velocities arising from the second rotor of a tandem or side-by-side-rotor helicopter and the induced flow angle at a horizontal tail plane" (p. 1).

From Introduction: "The primary purpose of the investigation described in the present described in the present report is to formulate a method which is of value for qualitative calculations of base pressure both on airfoils and bodies."