Report presenting the effects of an angle of incidence of 4 degrees and body indentation on wing loads of a sweptback wing-body combination at a range of Mach numbers. The wing had an aspect ratio of 4, taper ratio of 0.3, 45 degrees of sweepback of the quarter-chord line, and NACA 65A006 airfoil sections parallel to the plane of symmetry. Results regarding the effect of incidence and effect of body indentation are provided.

Memorandum presenting an investigation of the effect of base bleed on the base force of a supersonic-interceptor model in the 8- by 6-foot supersonic wind tunnel. Two groups of fixed-geometry nozzles and shroud combinations simulating double-iris-type configurations were evaluated over a range of secondary to primary exit-diameter ratios.

Report discussing testing on a supersonic-type propeller designed for a forward Mach number of 0.95, advance ratio of 2.2, and power coefficient of 0.26. Thrust distributions were found to be smooth and uniform over a range of Mach numbers, indicating efficient operation.

Report presenting calculations of the initial inclination of the mixing boundary separating an exhausting supersonic jet from an external supersonic stream as a function of jet static-pressure ratio.

Performance characteristics of a two-dimensional isentropic diffuser have been experimentally determined at a Mach number of 3.85. At zero angle of attack, a maximum total-pressure recovery of 0.41 was obtained with a supercritical mass-flow ratio of 0.95. As a consequence of the twin-duct arrangement of the diffuser, a large discontinuity in pressure recovery and mass flow with a characteristic hysteresis was encountered between critical and subcritical operation. An asymmetric shock pattern with large-scale separation and flow reversal in one of the passages occurred at reduced mass flows. Pressure and force data presented for an angle-of-attack range from zero to 4 degrees.

Report presenting an investigation conducted to determine the overall performance of the J73 two-stage turbine with a standard rotor-blade configuration. The turbine operated with a maximum brake internal efficiency between 0.91 and 0.92 at an overall pressure ratio of about 3.4 and 120 percent equivalent design rotor speed. Results regarding the overall performance, variation of equivalent weight flow with overall pressure ratio, and effect of limiting blade loading are provided.

From Introduction: "The investigation reported herein is a continuation of a ram-jet-combustor design program being conducted at the NACA Lewis laboratory. The purpose of this broad program is to establish basic design criteria for combustors operating over wide range of fuel-air ratio with low pressure losses and high combustion efficiency, and to utilize these design criteria in the development of practical ram-jet combustors."

Report discussing testing of a rocket-propelled airplane configuration model and a drag model, each with a 60 degree swept wing of aspect ratio 2.24, and different fuselages, at a Mach number range of 0.75 to 1.50. Information about the longitudinal stability, control, and drag characteristics and minimum-drag characteristics is presented.

Report presenting the zero-lift drag of a sweptback wing and body combination with nacelles with NACA 1-50-250 nose inlets locate in the wing tips as determined by flight tests of rocket-powered models at transonic speeds. Results regarding the pressure recovery and the effect of the nacelles on it are also provided.

Report presenting an investigation in the low-turbulence pressure tunnel at Mach number 1.2 to determine lift, drag, and moment characteristics of a wing with an airfoil section designed for maximum lift at low speeds, 45 degrees of sweepback, aspect ratio 4, and taper ratio 0.6. A similar wing with the NACA 65A006 airfoil section was also investigated and compared to the experimental wing.

Memorandum presenting minimum spark-ignition engines at reduced pressures for ethane, ethylene, acetylene, n-hexane, cyclohexane, and benzene.

Report presenting an investigation of the effects of suction through a porous leading-edge surface in the 19-foot pressure tunnel on a wing with 37 degrees of sweepback of the leading edge, an aspect ratio of 6, taper ratio of 0.5, and NACA 64(sub 1)-212 airfoil sections normal to the 27-percent-chord line. Results regarding the wing without flaps, wing with trailing-edge flaps, and power requirements for porous-leading-edge suction are provided.

"Flight measurements of the stability characteristics of the Bell X-5 research airplane at 59 deg sweepback were made in steady sideslips at Mach numbers from 0.62 to 0.97 at altitudes ranging between 35,000 and 40,000 feet. The results showed that the apparent directional stability was positive and increased at Mach numbers above 0.90. The apparent effective dihedral was positive and high, increasing at Mach numbers above 0.75" (p. 1).

From Introduction: "Analyses of heat transfer for liquid metals flowing turbulently in smooth tubes (low Pradtl numbers) are given in reference 1 and 2. The predicted heat-transfer coefficients from these analyses are considerably higher than those determined in the experimental heat-transfer investigations for mercury and lead bismuth given in references 2 to 4. If the analytical and experimental results for flow of gases are compared at low Peclet numbers, they are also found to be in disagreement (references 5 and 6)."

From Summary: "Force characteristics determined from tank tests of a 1/5.78-scale model of a hydro-ski-wheel combination for the Grumman JRF-5 airplane are presented. The model was tested in both the submerged and planing conditions over a range of trim, speed, and load sufficiently large to represent the most probable full-size conditions."

Memorandum presenting an investigation at a Mach number of 1.62 in the 9-inch supersonic tunnel of a series of missile configurations with tandem lifting surfaces of low aspect ratio and of nearly equal span. Some of the variables investigated were interdigitation angle, wing and tail plan form, and longitudinal location of wing with respect to tail. Lift, drag, and pitching-moment data are presented, together with center-of-pressure locations and tail-lift efficiency factors.

Report presenting an investigation of the effects of a systematic variation of trailing-edge thickness of a symmetrical, circular-arc airfoil on the aerodynamic force, moment, base-pressure, and wake fluctuations using the transonic-bump testing technique. Results regarding the effects of a systematic variation of the trailing-edge thickness, investigation of a boattailed trailing edge, and wake fluctuation characteristics are provided.

"At the request of the Bureau of Aeronautics, Navy Department, an investigation of the low-speed, power-off stability and control characteristics of a 1/10-scale model of the McDonnell XF3H-1 airplane has been made in the Langley free-flight tunnel. Flight tests of the model in the clean and in the slats-and-flaps-extended conditions were made over a lift-coefficient range from about 0.5 through the stall. Only low-altitude conditions were simulated and no attempt was made to determine the effect on the stability characteristics of freeing the controls" (p. 1).

Report presenting a wind-tunnel investigation to determine the effects of two wing-root leading-edge plan-form modifications, including a notched leading-edge fillet and a rounded leading-edge fillet, on the low-speed longitudinal stability characteristics of an airplane model with a 50.7 degree sweptback wing. Results regarding stability at zero lift, variation of stability with lift coefficient, and lift and drag characteristics are provided.

Report presenting a low-speed investigation of the static longitudinal aerodynamic characteristics of a twisted and cambered wing with 45 degrees of sweepback and an aspect ratio of 8.0 in the 19-foot pressure tunnel. Testing included the effects of leading- and trailing-edge flaps, flow control fences, and a fuselage. Report presenting longitudinal stability characteristics, lift characteristics, drag characteristics, fuselage effects, Reynolds number effects, effect of wing roughness are provided.

Report presenting an investigation at transonic speeds to determine the control characteristics of a linked flap and spoiler. The control consisted of a linked combination of a quarter-span inboard plug-type spoiler and a full-span flap. Results regarding the hinge-moment, pitching-moment, lift, and rolling-moment are provided.

"A summary and analysis have been made of the results of various investigations to determine the aerodynamic characteristics of a supersonic aircraft configuration. The configuration has a wing with 40 degree sweepback at the quarter-chord line, aspect ratio 4, taper ratio 0.5, and 10-percent-thick circular-arc sections normal to the quarter-chord line. Experimental data were available for a Mach number range from 0.16 to 2.32. Results obtained from wing-flow, rocket-model, transonic-bump, and tunnel tests are presented and, where possible, are supplemented by empirical and theoretical calculations" (p. 1).

A preliminary investigation was conducted to determine the combustion characteristics of a fuel composed of 50 percent pentaborane and 50 percent JP-4 (MIL-F-5624A) by weight in a turbojet combustor. A combustor designed to fit the housing of a J33-A-23 turbojet engine was selected for convenience. The fuel was evaluated at two engine conditions simulating altitudes of 40,000 and 57,000 feet, an engine speed of 85 percent of rated rpm, and a flight Mach number of 0.6. The pentaborane blend was initially evaluated in combustors developed for pure pentaborane and diborane reported in NACA RM E53B18 and RM E52L15. The performance of the blend was unsatisfactory in these combustors. A new combustor was then developed which provided combustor efficiencies measured from 91 to 101 percent as compared with efficiencies of 92 to 94 percent previously obtained for pentaborane at comparable conditions. Additional refinements of design details are needed to obtain lower oxide deposits and a more uniform outlet temperature profile; however, the combustor is believed to incorporate some of the design principles required to obtain satisfactory over-all performance with the fuel blend investigated.

Report presenting an investigation on a supersonic scoop inlet derived from a conical spike nose inlet at Mach numbers of 1.3, 1.6, and 1.9. The pressure recoveries of both inlets were similar. Results regarding the pressure drag, amounts of boundary-layer suction, and comparison of the inlets under several conditions are provided.