Report presenting the zero-lift drag of a sweptback wing and body combination with nacelles with NACA 1-50-250 nose inlets locate in the wing tips as determined by flight tests of rocket-powered models at transonic speeds. Results regarding the pressure recovery and the effect of the nacelles on it are also provided.

Report presenting wind-tunnel testing at Mach numbers of 1.5 and 2.0 to investigate the force, moment, and control characteristics of a canard missile configuration and its components in pitch and sideslip. The missile had small all-movable horizontal control surfaces at the nose and a cruciform wing at the rear, all of trapezoidal plan form. Trailing-edge flaps on the vertical fins were provided to supply directional control.

An analog investigation of the power plant for a gas-turbine powered helicopter indicates that currently proposed turbine-propeller engine controls are satisfactory for helicopter application. Power increases from one-half to full rated at altitudes from sea level to 15,000 feet could be made in less than 4 seconds with either the rotor or propellers absorbing the engine power.

Report presenting an investigation in the low-turbulence pressure tunnel at Mach number 1.2 to determine lift, drag, and moment characteristics of a wing with an airfoil section designed for maximum lift at low speeds, 45 degrees of sweepback, aspect ratio 4, and taper ratio 0.6. A similar wing with the NACA 65A006 airfoil section was also investigated and compared to the experimental wing.

Memorandum presenting minimum spark-ignition engines at reduced pressures for ethane, ethylene, acetylene, n-hexane, cyclohexane, and benzene.

Report presenting an investigation of the effects of suction through a porous leading-edge surface in the 19-foot pressure tunnel on a wing with 37 degrees of sweepback of the leading edge, an aspect ratio of 6, taper ratio of 0.5, and NACA 64(sub 1)-212 airfoil sections normal to the 27-percent-chord line. Results regarding the wing without flaps, wing with trailing-edge flaps, and power requirements for porous-leading-edge suction are provided.

"Flight measurements of the stability characteristics of the Bell X-5 research airplane at 59 deg sweepback were made in steady sideslips at Mach numbers from 0.62 to 0.97 at altitudes ranging between 35,000 and 40,000 feet. The results showed that the apparent directional stability was positive and increased at Mach numbers above 0.90. The apparent effective dihedral was positive and high, increasing at Mach numbers above 0.75" (p. 1).

Memorandum presenting flight tests made on the Bell X-1 airplane with the 10-percent-thick wing and the 8-percent-thick tail to evaluate the effects of fixing the rudder and changing the inclination of the principal axes of inertia. The data were obtained during power-off glides at altitudes between 32,000 and 16,000 feet.

Analytical methods are presented for the determination of local values of outside and inside heat-transfer coefficients and effective gas temperatures by use of turbine-blade-temperature measurements. The methods are derived for a number of configurations that can be applied to typical cooled-turbine-blade shapes as well as to other types of heat-transfer apparatus.

Report presenting flight measurements of aerodynamic tail loads made on the Douglas D-558-II from which the variation with Mach number of the wing-fuselage aerodynamic center, static-longitudinal-stability parameter, the tail load per g, and the zero-lift wing-fuselage pitching-moment coefficient determined up to Mach number 0.87.

Report presenting results from a preliminary flight investigation on a swept-wing airplane of the lateral-control characteristics and wing-dropping tendency encountered at high Mach numbers. Measurements of aileron and rudder-control effectiveness are presented and used with estimated damping-in-roll characteristics and data from steady sideslips to approximate the variation of effective dihedral with Mach number.

Report presenting flight measurements of the dynamic longitudinal-stability characteristics of a 35 degree swept-wing airplane. The results indicated that a sharp reduction in damping at a Mach number of 0.92 with maximum damping occurred at Mach number of 0.88 and 0.94. Results regarding oscillation periods, damping coefficients, scatter, and number of cycles required for oscillations to damp to a certain amplitude are provided.

Report presenting the results of an investigation of a model of the Bumblebee XPM missile to determine the causes of booster-fin failures on full-scale missiles. Results indicated that failures of the fins were due to launching shoes which caused the missile to try at increasingly negative angles of attack as the Mach number increased.

Report discussing testing to determine the sensitivity to sideslip of the static-pressure orifices of the Boeing B-29. The purpose was to determine the errors in indicated altitude and vertical velocity that occur when an airplane experiences oscillations in sideslip on a bombing run. The sensitivity of the orifices to sideslip was determined by measurements of pressure and sideslip angle during constant-amplitude oscillations in sideslip.

From Introduction: "Analyses of heat transfer for liquid metals flowing turbulently in smooth tubes (low Pradtl numbers) are given in reference 1 and 2. The predicted heat-transfer coefficients from these analyses are considerably higher than those determined in the experimental heat-transfer investigations for mercury and lead bismuth given in references 2 to 4. If the analytical and experimental results for flow of gases are compared at low Peclet numbers, they are also found to be in disagreement (references 5 and 6)."

From Summary: "Force characteristics determined from tank tests of a 1/5.78-scale model of a hydro-ski-wheel combination for the Grumman JRF-5 airplane are presented. The model was tested in both the submerged and planing conditions over a range of trim, speed, and load sufficiently large to represent the most probable full-size conditions."

Memorandum presenting an investigation at a Mach number of 1.62 in the 9-inch supersonic tunnel of a series of missile configurations with tandem lifting surfaces of low aspect ratio and of nearly equal span. Some of the variables investigated were interdigitation angle, wing and tail plan form, and longitudinal location of wing with respect to tail. Lift, drag, and pitching-moment data are presented, together with center-of-pressure locations and tail-lift efficiency factors.

Report presenting an investigation of the effects of a systematic variation of trailing-edge thickness of a symmetrical, circular-arc airfoil on the aerodynamic force, moment, base-pressure, and wake fluctuations using the transonic-bump testing technique. Results regarding the effects of a systematic variation of the trailing-edge thickness, investigation of a boattailed trailing edge, and wake fluctuation characteristics are provided.

"At the request of the Bureau of Aeronautics, Navy Department, an investigation of the low-speed, power-off stability and control characteristics of a 1/10-scale model of the McDonnell XF3H-1 airplane has been made in the Langley free-flight tunnel. Flight tests of the model in the clean and in the slats-and-flaps-extended conditions were made over a lift-coefficient range from about 0.5 through the stall. Only low-altitude conditions were simulated and no attempt was made to determine the effect on the stability characteristics of freeing the controls" (p. 1).

Report presenting a wind-tunnel investigation to determine the effects of two wing-root leading-edge plan-form modifications, including a notched leading-edge fillet and a rounded leading-edge fillet, on the low-speed longitudinal stability characteristics of an airplane model with a 50.7 degree sweptback wing. Results regarding stability at zero lift, variation of stability with lift coefficient, and lift and drag characteristics are provided.

Report presenting a low-speed investigation of the static longitudinal aerodynamic characteristics of a twisted and cambered wing with 45 degrees of sweepback and an aspect ratio of 8.0 in the 19-foot pressure tunnel. Testing included the effects of leading- and trailing-edge flaps, flow control fences, and a fuselage. Report presenting longitudinal stability characteristics, lift characteristics, drag characteristics, fuselage effects, Reynolds number effects, effect of wing roughness are provided.

Report presenting an investigation at transonic speeds to determine the control characteristics of a linked flap and spoiler. The control consisted of a linked combination of a quarter-span inboard plug-type spoiler and a full-span flap. Results regarding the hinge-moment, pitching-moment, lift, and rolling-moment are provided.

"A summary and analysis have been made of the results of various investigations to determine the aerodynamic characteristics of a supersonic aircraft configuration. The configuration has a wing with 40 degree sweepback at the quarter-chord line, aspect ratio 4, taper ratio 0.5, and 10-percent-thick circular-arc sections normal to the quarter-chord line. Experimental data were available for a Mach number range from 0.16 to 2.32. Results obtained from wing-flow, rocket-model, transonic-bump, and tunnel tests are presented and, where possible, are supplemented by empirical and theoretical calculations" (p. 1).

A preliminary investigation was conducted to determine the combustion characteristics of a fuel composed of 50 percent pentaborane and 50 percent JP-4 (MIL-F-5624A) by weight in a turbojet combustor. A combustor designed to fit the housing of a J33-A-23 turbojet engine was selected for convenience. The fuel was evaluated at two engine conditions simulating altitudes of 40,000 and 57,000 feet, an engine speed of 85 percent of rated rpm, and a flight Mach number of 0.6. The pentaborane blend was initially evaluated in combustors developed for pure pentaborane and diborane reported in NACA RM E53B18 and RM E52L15. The performance of the blend was unsatisfactory in these combustors. A new combustor was then developed which provided combustor efficiencies measured from 91 to 101 percent as compared with efficiencies of 92 to 94 percent previously obtained for pentaborane at comparable conditions. Additional refinements of design details are needed to obtain lower oxide deposits and a more uniform outlet temperature profile; however, the combustor is believed to incorporate some of the design principles required to obtain satisfactory over-all performance with the fuel blend investigated.