Report presenting an investigation at transonic speeds of the control balancing characteristics of three tabs on a full-span flap on an aspect-ratio-3, 45 degree sweptback wing. The results indicated that all the tabs tested, inset, attached, or detached, would balance the flap hinge moments throughout the speed range.

Memorandum presenting a group of alkylsilanes consisting of monoethylsilane, diethylsilane, and trimethylsilane prepared in 65- and 90-percent yield by reduction of the respective alkylchlorosilanes with either lithium hydride or lithium aluminum hydride. The boiling points, densities, refractive indices, and freezing points were determined and presented with a survey of literature values.

Report presenting sound measurements at static conditions for a two-blade, 47-inch-diameter propeller over a range of tip Mach numbers. For comparison, spectrums have been obtained at both subsonic and supersonic tip speeds. Results regarding the experimental results and comparison with theory are provided.

"The method of Lagrange multipliers is used to take account of the dynamic effects of the constraints at the wing tips when two identical airplanes are coupled to the wing tips of a "mother" airplane. The resulting equations of motion of this symmetrical configuration are derived for one, two, or three degrees of rotational freedom at each joint" (p. 1).

Report presenting the results of nine experimental flutter tests involving two flat-plate models and two rib and spar models of NACA 0012 airfoil sections in order to give a comparison of the flutter characteristics of wings with M and W type plan forms. The W plan form generally gave higher flutter speeds than the M plan forms.

Report presenting tests using the NACA wing-flow method at a range of Mach numbers to determine the aerodynamic characteristics of four triangular-wing-fuselage models. Measurements of the normal force, chord force, and pitching moment for various angles of attack. Two models had wings of aspect ratio 2.31, one with an NACA 65-009 airfoil section and one with a 9-percent-thick biconvex section, and two with wings of aspect ratio 4, one with an NACA 65-006 airfoil and one with a 6-percent-thick double-wedge airfoil.

Report presenting a wing-body combination with a plane triangular wing of aspect ratio 4 and 3-percent-thick, biconvex sections in streamwise planes at subsonic and supersonic Mach numbers. Lift, drag, and pitching moment are presented for a range of Mach and Reynolds numbers.

Report presenting the wing-aileron rolling effectiveness and drag for full-span sealed ailerons on untapered wings over a range of Mach numbers by using rocket-propelled test vehicles in free flight.

Report presenting an investigation of the altitude operational characteristics of a prototype model of the J47D turbojet engines, which includes an afterburner, a variable-area exhaust nozzle, and an integrated electronic control in an altitude wind tunnel. Results regarding compressor stall, compressor unstall, combustor blow-out during acceleration, stall and blow-out protection, acceleration characteristics, deceleration characteristics, and altitude starting characteristics, afterburner operational characteristics are provided.

Report presenting an experimental investigation utilizing rocket propelled vehicles in free flight to determine some effects of fuselage interference, wing interference, and sweepback on the damping-in-roll characteristics of untapered wings with an aspect ratio of 3.7 and NACA 65A009 airfoil sections between a range of Mach numbers.

Report presenting an investigation of the low-speed lateral characteristics of a 47.5 degree sweptback-wing-fuselage combination with several flap and spoiler aileron arrangements. Results regarding aileron control characteristics, spoiler-control characteristics, and a comparison of the two are provided.

Memorandum presenting the application of the concept of indicial functions to the analysis of the aerodynamic phenomena associated with the short-period pitching mode of wings in subsonic and supersonic flight. Simple physical relationships are pointed out and are used to study the effect on the rotary-damping-moment coefficient of changes in center-of-gravity position, Mach number, aspect ratio, plan form, frequency, and thickness.

Report presenting a study of the storage properties of fuming nitric acids, with and without additives, at 170 degrees F in closed containers of aluminum bodies and steel caps. The effects on the storage properties indicated that the potassium fluoride dihydrate is most effective in reducing the rate of pressure rise and reducing corrosion on aluminum and stainless steel surfaces.

Report discussing testing of a helicopter rotor powered by pulse-jet engines located at the rotor-blade tips. The basic hovering characteristics of the rotor and propulsive characteristics of the pulse-jet engine were obtained at a range of engine speeds with the engines rigidly fixed to the blade tips and with the engines free to pivot. Measurements were also taken to determine the effect of inlet blockage on the power-off drag of the jet engines and the noise intensity in the vicinity of operating engines.

Field measurements were made on a fighter airplane to determine the approximate magnitude of the horizontal tail loads in accelerated flight. In these flight measurements, pressures at a few points were used as an index of the tail loads by correlating these pressures with complete pressure-distribution data obtained in the NACA full-scale tunnel. In addition, strain gages and motion pictures of tail deflections were used to explore the general nature and order of magnitude of fluctuating tail loads in accelerated stalls.

From Summary: "A summary has been made of the available experimental data on division of normal-force loads between the wing and fuselage of aircraft. Comparison of the experimental values with theoretical calculations which include interference effects shows good agreement in general with the greatest differences occurring near a Mach number of 1.0. At high angles of attack, above the range of linear lift curves, the proportion of the total wing-fuselage load carried by the wing decreases and this effect occurs throughout the subsonic- and transonic-speed region."

"Theoretical calculations of the stability derivatives at supersonic speeds for a high-speed airplane configuration are presented. The range of Mach numbers considered includes those cases for which the wing and tail surfaces have subsonic leading edges, supersonic leading edges, and combinations of the two. The methods of analysis are discussed; these represent detailed consideration of the important effects and contributions of the various airplane components utilizing available theories and theoretically justifiable and reasonable approximations" (p. 1).

Report presenting an experimental investigation at Mach number 1.90 to determine the effect of a diverter-type boundary-layer removal system on the performance of a scoop inlet. The supersonic portion of the inlet consisted of a two-dimensional, reverse Prandtl-Meyer turn followed by a constant-area throat. Results regarding the effect of fuselage position and subsonic diffuser performance are provided.

Report presenting an experimental investigation of the application of transpiration air-cooling to the combustion-chamber wall of an afterburner. Results regarding the typical temperature and pressure profiles, correlation of wall temperatures, distribution of cooling-air flux density, longitudinal distribution of cooling air, longitudinal distribution of wall temperature, effect of permeability on cooling-air requirements, and fabricating and operating problems are provided.

Report presenting an investigation to determine the effects of a horizontal tail on the longitudinal stability characteristics of a swept-back, twisted, and cambered wing in combination with a fuselage and various combinations of high-lift and stall-control devices. The ideal placement of the horizontal tail appeared to be at 6 percent wing semispan below the wing-root-chord plane.

From Introduction: "The rolling-pullout maneuver (any maneuver in which rolls occur during high g flight conditions) has been shown to be pertinent to design considerations from the standpoint of the loads produced on a vertical tail (refs. 1 to 3). In order to understand this problem better, the results of an analytical study of effects of large variations of some of the lateral-stability-derivative coefficients on the maximum angle of sideslip at first peak of its oscillation are presented in this paper. Also, expressions for estimating the effects of small variations of or errors in these coefficients on the maximum sideslip angle have been developed and are presented. "

Report presenting the effect of preinjection-fuel temperature on vaporization rates and combustion efficiency of a 16-inch ram-jet engine for two different fuels. Variation of the location of the fuel injectors and use of control sleeves were also explored.

Report presenting an investigation in the high-speed 7- by 10-foot tunnel to determine the effectiveness of a spoiler-slot-deflector combination in producing rolling moments in the transonic speed range at angles of attack as high as 24 degrees over a range of Mach numbers. The wing had an aspect ratio of 4, a taper ratio of 0.6, an unswept quarter-chord line, and NACA 65A006 airfoil sections.

Memorandum presenting testing of a D-558-II airplane with the wing slats fully extended, with and without inboard wing fences, and with the wing slats half extended and wing fences removed. In order to improve the stick-force characteristics at moderate and large angles of attack, additional tests were conducted with two bungees of differing stiffness alternately attached to the control column.