Report presenting the results of testing in the transonic range of four flutter airfoils attached to a freely falling body. Failures of the airfoils were metered and recorded in order to determine the Mach numbers and altitudes of failure.

"The tests reported herein were made for the purpose of determining the high-speed load distribution on the wing of a 3/16 scale model of the Douglas XSB2D-1 airplane. Comparisons are made between the root bending moment and section torsional moment coefficients as obtained experimentally and derived analytically. The results show good correlation for the bending moment coefficients but considerable disagreement for the torsional moment coefficients, the measured moments being greater than the analytical moments. The effects of Mach number on both the bending moment and torsional moment coefficients were small" (p. 1).

From Summary: "A theoretical investigation of the velocity profiles for laminar mixing of a high-velocity stream with a region of fluid at rest has been made assuming that the Prandtl number is unity. A method which involves only quadratures is presented for calculating the velocity profile in the mixing layer for an arbitrary value of the free-stream Mach number. Detailed velocity profiles have been calculated for free-stream Mach numbers of 0, 1, 2, 3, and 5."

From experience gained by NACA test pilots in flying at high subsonic Mach numbers and from interpretation of the data obtained, some general precautionary rules for test flying near sonic Mach numbers have been formulated. The reasons for these rules are discussed and observations are made with respect to the hazards arising from undesirable stability and control characteristics which have been noted in test flights of various airplanes. This paper, although written primarily for the attention of test pilots, contains general information of interest to those who are concerned with various phases of flight testing near sonic Mach numbers.

Report presenting a wind-tunnel investigation of a semispan pointed wing of aspect ratio 1.7 with 60 degree leading-edge sweepback and 30 degree trailing-edge sweepforward with a control surface. The purpose of the investigation was to determine the effectiveness of flap-type controls at transonic and supersonic speeds. Results regarding the wing characteristics and control-surface characteristics are provided.

"In order to determine the aerodynamic effects of an auxiliary belly fuel tank on the Grumman F8F-1 airplane, a wind-tunnel investigation was made on a 1/5 - scale model of the Grumman XF8F-1 airplane. Pitch and yaw tests were made with the model in the cruising and landing configurations for windmilling and take-off power conditions. Tuft studies and static-pressure measurements were also made to determine the flow characteristics in the region of the fuel tank" (p. 1).

Report discussing testing on two types of single cylinders to determine the effect of the relation of exhaust pressure to inlet-air pressure on knock-limited performance. Variables explored included exhaust pressure, fuel-air ratio, and engine speed. Three types of fuels were also used to explore the effect of exhaust pressure on fuel ratings.

Report presenting an investigation to obtain the pressure distribution over a sharp-nose body of revolution with a circular-arc profile and fineness ratio 6 at transonic speeds using the NACA wing-flow method. Results regarding the variation of pressure coefficient with Mach number, pressure distributions along the body axis, pressure drag, and effects of interference and horizontal gradient are provided.

Operating characteristics of the 11-stage 4000-pound-thrust axial-flow turbojet engine were determined. A standard compressor and a compressor with the blade angles of the rotor and stator blades increased 5 degrees to obtain greater air flow, were investigated.

"Available information on gust structure, airplane reactions, and pertinent operating statistics has been examined. This report attempts to coordinate this information with reference to the prediction of gust loads on airplanes. The material covered represents research up to October 1947" (p. 807).

The sea-level performance of I-16 turbojet engine at zero ram was investigated to determine the effects of an intake duct, shroud, and tail pipe intended for installation in an XFR-1 airplane. Engine speeds ranged from 8000 to 16,500 rpm for several variations of the intake duct and tail pipes.

A wind tunnel investigation was conducted to determine the performance of a 4000-pound-thrust axial-flow turbojet engine with a high flow compressor. Pressure altitudes included 5000 to 40000 feet with ram pressure ratios from 1.00 to 1.82. Altitudes included 20000 to 40000 feet and ram pressure ratios from 1.09 to 1.75. A comparison is made between engine performance with high flow and low flow compressors.

The gust and draft velocities from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from August 16, 1947 to August 20, 1947 are presented.

The gust and draft velocities from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from September 10, 1947 to September 15, 1947, are presented.

From Summary: "The results of an experimental investigation of an NACA submerged-air-inlet system on a 1/5-scale model of a fighter airplane are presented. Preliminary development tests were conducted to select the optimum entrance configuration. Duct-system total-pressure losses and pressure distributions over the lip and ramp of this air intake were obtained."

The variation of pressure distribution is calculated for a two-dimensional supersonic airfoil either experiencing a sudden angle-of-attack change or entering a sharp-edge gust. From these pressure distributions the indicial lift functions applicable to unsteady lift problems are determined for two cases. Results are presented which permit the determination of maximum increment in lift coefficient attained by an unrestrained airfoil during its flight through a gust. As an application of these results, the minimum altitude for safe flight through a specific gust is calculated for a particular supersonic wing of given strength and wing loading.

Report presenting measurements using the NACA wing-flow method of the lift, pitching-moment, and hinge-moment characteristics of a 35 degree sweptback NACA 65-009 airfoil of aspect ratio 3.04 with a full-span 1/4-chord unsealed plain flap. The tests were carried out at a range of Mach numbers, Reynolds numbers, angles of attack, and flap deflections. Variations of lift and pitching moment with angle of attack or flap deflection were approximately rectilinear at all Mach numbers for moderate angles of attack and flap deflections.

This report has been prepare in response to a request for information from an aircraft company. A typical example was selected for the presentation of an approximate method of calculation of the relative humidity required to prevent frosting on the inside of a plastic window in a pressure type cabin on a high speed airplane. The results of the study are reviewed.

Report presenting testing of a cambered and twisted wing with constant-chord elevons with a slender fuselage to determine the longitudinal and lateral control from the elevons for a range of Mach numbers. Results regarding lift, drag, pitching-moment, and rolling-moment characteristics for various elevon deflections are provided.

"A method is presented for predicting the amplitude and frequency, under certain simplifying conditions, of the hunting oscillations of an automatically controlled aircraft with lag in the control system or in the response of the aircraft to the controls. If the steering device is actuated by a simple right-left type of signal, the series of alternating fixed-amplified signals occurring during the hunting may ordinarily be represented by a "square wave." Formulas are given expressing the response to such a variations of signal in terms of the response to a unit signal" (p. 487).

Report presenting a flight investigation conducted to establish the heat requirements for ice prevention on aircraft windshields mounted on the forebody of an airplane at several angles. Electrically heated windshields were used in order to provide accurate measuring of heat input to the windshield. Results regarding the quantity of heat provided, amount of water collection, ideal windshield angle, ranges in airplane velocity, and icing conditions are provided.

"An investigation has been conducted in the Langley 20-foot free-spinning tunnel of a 1/29-scale model of the Republic XF-91 airplane with a.conventional-tail arrangement installed. Previously, tests were made on the model with a vee tail installed. The erect spin and recovery characteristics of the model were determined for the normal loading with the wing installed at various amounts of incidence. The spin investigation also included inverted-spin tests, spin-recovery-parachute tests, tests with the center of gravity moved rearward, and tests with external fuel tanks added to the model" (p. 1).

The present paper is a continuation of a theoretical investigation of the stability of the laminar boundary layer in a compressible fluid. An approximate estimate for the minimum critical Reynolds number, or stability limit, is obtained in terms of the distribution of the kinematic viscosity and the product of the mean density and mean vorticity across the boundary layer. The extension of the results of the stability analysis to laminar boundary-layer gas flows with a pressure gradient in the direction of the free stream is discussed.

"An investigation of the DM-1 Glider, which had approximately triangular plan form, an aspect ratio of 1.8 and a 60 degree sweptback leading edge, has been conducted in the Langley full-scale tunnel. The investigation consisted of the determination of the separate effects of the following modifications made to the glider on its maximum lift and stability characteristics: (a) installation of sharp leading edges over the inboard semispan of the wing, (b) removal of the vertical fin, (c) sealing of the elevon control-balance slots, (d) installation of redesigned thin vertical surfaces, (e) installation of faired sharp leading edges, and (f) installation of canopy" (p. 1).