Using a pair of lasers near 6000 A, the J = 6 ground state is excited to a J = 6 intermediate level and then to a J = 5 upper state. Non-resonant fluorescences from both excited states are separately detected. Results of a set of model calculations are tabulated. Level 3 average populations are always very small, since the system decays rapidly into inaccessible metastable states. This means that chemistry experiments are difficult. The differences between parallel and perpendicular polarization are modest. The fluorescence dips converge to a value near 50%. The level 3 populations do not approach a common value. This means that the most reliable experimental measurement does not determine the level populations. The most striking changes appear in the last two, most exact, models. The difference between the models is that one includes, for the first time, the linear frequency chirp produced by the fanlike spread of the focussed laser beams. This seemingly innocuous change halves the population left in the ground state. It appears that analogues of adiabatic passage and adiabatic rapid passage respectively are being observed.

This manual describes the use and structure of the June 30, 1976 version of the Four-D propagation code for high energy laser beams. It provides selected sample output from a typical run and from several debug runs. The Four-D code now includes the important noncoplanar scenario feature. Many problems that required excessive computer time can now be meaningfully simulated as steady-state noncoplanar problems with short run times.

Most detailed fusion target design is done by numerical simulation using large computers. Although numerical simulation is briefly discussed, this lecture deals primarily with the way in which basic physical arguments, driver technology considerations and economical power production requirements are used to guide and augment the simulations. Physics topics discussed include target energetics, preheat, stability and symmetry. A specific design example is discussed.

The Program Plan specifies the basic plan for the utilization of FY-74 funds allocated by the AEC Division of Applied Technology and contributions from other participants for the development of geothermal energy in southern Idaho. Funding priorities are dictated by the Construction Data Package submission deadline and the October 1, 1974, site selection. Tasks not funded during FY-74 will be pursued during FY-75. (auth)

Progress is reported on the following: well conditions; perforating and cementing; temperature-depth plot; slotted liner, well head and auxiliary equipment; well testing and analysis program; well monitoring during standby; environmental assessment; time schedule; and budgets. (MHR)

Voitenko compressors are used to generate 43 mm/..mu..s air shocks in both a steel and a grout outlet pipe containing ambient atmospheric air. Fiber-optic ports provide diaphragm burst times, time-of-arrival (TOA) data, and velocities for the shock front along the 20-mm-ID exit pipes. Pressure profiles are obtained at higher enthalpy shock propagation than ever before and at many locations along the exit pipes. Numerous other electronic sensors and postshot observations are described, as well as experimental results. The primary objectives of the experiments are as follows: (1) provide a data base for normalization/improvement of existing finite-difference codes that describe high-energy air shocks and gas propagation; (2) obtain quantitative results on the relative attenuation effects of two very different wall materials for high-energy air shocks and gas flows. The extensive experimental results satisfy both objectives.

Results of homogeneous catalytic hydrogenation of complex unsaturated substrates including coal and coal-derived materials are reported, with organic soluble molecular complexes as catalysts. Among the substrates used were Hvab coal, solvent-refined coal, and COED pyrolysate. The hydrogenations were carried out in an autoclave. The results are summarized in tables.

Control technologies to manage environmental impacts from geothermal developments in California's Imperial Valley from development to 1985 are discussed. Included are descriptions of methods for managing land subsidence by fluid injection; for preventing undesirable induced seismicity or mitigating the effects of seismic events; for managing liquid wastes through pretreatment or subsurface injection; for controlling H/sub 2/S by dispersal, reinjection, and chemical treatment of effluents; and for minimizing the impact of noise from power plants by setting up buffer zones and exclusion areas.

By exposing samples to various irradiance levels from a calibrated thermal radiation source, the ignition responses of blackened alpha-cellulose and cotton cloth with and without fire-retardant additives were compared. Samples treated with retardant compounds which showed the most promise were then isothermally pyrolyzed in air for comparisons between the pyrolysis rates. Alpha-cellulose samples containing a mixture of boric acid, borax, and ammonium di-hydrogen phosphate could not be ignited by irradiances up to 4.0 cal cm/sup -2/ s-1 (16.7 W/cm/sup 2/). At higher irradiances the specimens ignited, but flaming lasted only until the flammable gases were depleted. Cotton cloth containing a polymeric retardant with the designation THPC + MM was found to be ignition-resistant to all irradiances below 7.0 cal cm/sup -2/ s/sup -1/ (29.3 W/cm/sup 2/). Comparison of the pyrolysis rates of the retardant-treated alpha-cellulose and the retardant-treated cotton showed that the retardant mechanism is qualitatively the same. Similar ignition-response measurements were also made with specimens exposed to ionizing radiation. It was observed that gamma radiation results in ignition retardance of cellulose, while irradiation by neutrons does not.

At the request of the Department of Energy, field techniques were developed to evaluate and improve the injection of brine into wells at Strategic Petroleum Reserve (SPR) sites. These wells are necessary for the disposal of saturated brine removed from salt domes where oil is being stored. The wells, which were accepting brine at 50 percent or less of their initial design rates, were impaired by saturated brine containing particulates that deposited on the sand face and in the geologic formation next to the wellbore. Corrosion of the brine-disposal pipelines and injection wells contributed to the impairment by adding significant amounts of particulates in the form of corrosion products. When tests were implemented at the SPR sites, it was found that the poor quality of injected brines was the primary cause of impaired injection; that granular-media filtration, when used with chemical pretreatment, is an effective method for removing particulates from hypersaline brine; that satisfactory injection-well performance can be attained with prefiltered brines; and that corrosion rates can be substantially reduced by oxygen-scavenging.

Expanded development of total-flow expander technology in order to obtain efficient energy extraction from the liquid flow component of the geothermal well flow, in addition to steam enthalpy conversion, has been undertaken by the University of California, Lawrence Livermore Laboratory (LLL). The flow conditions necessary for this type of complete system performance characterization are beyond the capabilities of the test facility utilized in the preliminary tests at the LLL hot-water test facility. As an alternative to increasing the existing facility to meet the expanded test requirements, test facilities in the industrial California community are being surveyed to assess their capability in supporting future tests of the LLL expander. Biphase Engines, Inc. of Santa Monica, California was contracted by LLL to perform this survey. The goal of the Biphase Engines survey is to identify organizations with, first, an interest in supporting the LLL turbine test program and, second, to review their test capabilities with respect to the turbine test requirements. The results of the survey are described in the following sections which includes a listing of all organizations contacted. The responses to all inquiries are given. The affirmative responses to the test-support requirement are detailed with a description of the test …

The objective of this investigation is to determine the upper limits on the thermal yield of a 1 kt source detonated at shallow depths. Three problems were computed for the depths of burial of 0.5, 1.5, and 3 m. The source is an iron bubble with 30 cm radius and 25 kg of mass. The computation was done on the CEL code. The results show that the relative thermal yield is no more than 6 percent, and that it vanishes at DOB of about 4 m. The computed blast strength is plotted against the range. The results are consistent with the measurements on ''Johnnie Boy'' and ''Jangle-U'', and in good agreement with the RAD9 calculations and the HULL calculations.

An elaboration of the ISABELLE concept as the model for a high energy, high luminosity proton-proton facility is given. Its place in the total high energy physics program is discussed. Certain features of the ISABELLE design which have not been consolidated, in particular injection and modes of beam operation, are considered. A new scheme is reviewed, one which could provide quick beam turn-on after construction, one in which there is a high probability of reaching and perhaps even exceeding the design objectives, one which should provide comparatively more flexible and reliable operation for physics, and finally one whose presence opens up a window to a much higher energy region. The new system involves the use of a physically separate current accumulator, allowing, therefore, the optimal utilization of the superconducting structures. The fact that an obvious addition to the complex will permit pp collisions in the 4 TeV center-of-mass energy region, which corresponds to an equivalent lab energy of approximately 10/sup 16/ eV, i.e., cosmic ray energies, prompts the added structure to be referred to as the COSMICTRON. The facility operated in the ''new'' manner proposed is considered to be ''the best ISABELLE that can be built.''

Since DNC was first introduced, four contractors for ERDA have become actively involved with its utilization. These contractors are Rockwell International, which operates the Rocky Flats plant at Golden, Colorado; Union Carbide Corporation operating the Y-12 plant at Oak Ridge, Tennessee; Sandia Laboratories, operating a plant in Albuquerque, New Mexico and the Bendix Corporation with a plant in Kansas City, Missouri. DNC activities at the four sites are elucidated by slides. At the present time, these four plants have a total of 17 machine tools operating under DNC control with over 50,000 of DNC operating time. Present planning calls for the addition of about this many more machines by the end of FY 1978.

A comprehensive set of kerma factors for neutrons and photons has been computed for the International Commission on Radiological Protection's (ICRP) standard man, ICRP soft tissue, ICRP red bone marrow, ICRP eye lens, H/sub 2/O, dry air, Al, Si, /sup 32/S, Ar, and four thermoluminescent dosimeter materials. The energy range for neutrons is 10/sup -9/ to 20 MeV, divided into 175 energy groups. For photons, the energy range is 10/sup -3/ to 20 MeV, and kerma factors are calculated at 144 energy values. The kerma factors were computed using the neutron group-averaged and photon pointwise Evaluated Nuclear Data Library. Results are compared with those in other works where appropriate. The use of kerma factors to convert fluence to absorbed-dose index for ICRP tissue is discussed.

Leach rates for /sup 237/Np and /sup 239/Pu are investigated with a single-pass leaching system. The factorial experimental design uses several combinations of solution composition and flow rate, and two temperatures, 25 and 75/sup 0/C. The 25/sup 0/C results are compared with those from a modified IAEA procedure. At 25/sup 0/C, leach rates decrease with time. Agreement between results from the single-pass and modified IAEA methods is fair with WIPP brine leachant, good with NaHCO/sub 3/, and good with distilled H/sub 2/O. Leach rates are approximately independent of flow rates at room temperature, but increase with flow rates at high temperature. Rates for /sup 237/Np increase with temperature, but those for /sup 239/Pu either decrease or do not change with temperature. 7 figures.

An investigation of available data on the saturation state of seawater with respect to calcium carbonate and its possible significance for scale formation on Ocean Thermal Energy Conversion (OTEC) heat exchangers has been carried out. Pertinent oceanographic data is lacking at or near potential OTEC sites for the calculation of the degree of saturation of seawater with respect to calcium carbonate. Consequently, only ''extrapolated'' saturation values can be used. These indicate that near surface seawater is probably supersaturated, with respect to the calcium carbonate phases calcite and aragonite, at all potential OTEC sites. The deep seawater that would be brought to the surface at the potential Atlantic Ocean sites is also likely to be supersaturated with respect to calcium carbonate. The deep seawater at the potential Pacific Ocean sites may be slightly undersaturated. The fact that OTEC heat exchangers will be operating in seawater, which is supersaturated with respect to calcium carbonate, means that if nucleation of calcite or aragonite occurs on the heat exchanger surfaces, significant growth rates of calcium carbonate scale may be expected. The potential for calcium carbonate nucleation is highest at cathodic metal surface locations, which are produced as the result of aluminum corrosion in seawater. …

A redesign of the LOFT instrument penetration necessitated a reanalysis of the thermal conditions existing in the nozzle and flange during a Loss of Coolant Experiment (LOCE). The maximum temperature gradient existing in the instrument flange will be used to determine the thermal stresses and maximum number of allowable cycles for the instrument flange. Based upon the specification and thermal conditions predicted by RELAP4/MOD5, the maximum temperature gradient through the flange will not exceed 216/sup 0/F. The thermal conditions predicted by RELAP4/MOD2 for the nozzle head penetration assembly were less severe than those used in the original thermal-stress analysis, so only the flange was analyzed here. If the thermal stresses are marginal with the 216/sup 0/F ..delta..T, a more detailed analysis should be done as the heat slab model used in RELAP is only one dimensional. Conservative hand calculations were performed for a heatup rate of 100/sup 0/F per hour and it was determined that the worst temperature gradient through the flange will be less than 81/sup 0/F.

Modification of the combined FI/EI ion source to permit operation in the FD mode is underway. Oxidation-reduction and activation cells were fabricated and assembly of the vacuum system for the activation cell is in progress. High- and low-voltage power supplies needed for emitter preparation were constructed. The sensitivity for field ionization of decane relative to that for ethylbenzene was measured as a function of binary mixture composition, ion-source temperature, and field strength. A gallium frit is being added to the all-glass inlet system. The purity of 25 saturates and naphthenes and 10 single-ring aromatics substituted with alkyl groups was checked using FID/GC.

This paper discusses some of the material considerations for inertially confined fusion reactors. A comparison of the material considerations for inertially confined reactors is made with those of magnetically confined reactors. The lithium fall reactor concept is used as an example of the freedom from constraints intrinsic to inertially-confined fusion reactors.

A brief parametric survey of the x-ray characteristics of a gold micro-disk irradiated at 3 x 10/sup 14/ watt/cm/sup 2/ by a 1 nsec Nd-glass laser pulse has been provided as an example of a laser generated bright x-ray source. It was shown that a simple phenomenological model of the laser generated x-ray source as a microscopic equilibrium plasma radiating as a blackbody for a finite time determined by its hydrodynamic disassembly and radiation losses, serves to provide an adequate approximation to the x-ray characteristics of such sources. The current state of x-ray microscopy within the LLL laser fusion program was briefly reviewed. Kirpatrick--Baez grazing incidence reflection x-ray microscopes are being used to provide 3 to 5 ..mu..m resolution, broadband images (..delta..E/E approx. 0.3) over a spectral range from .6 keV to 3.5 keV. Zone Plate Coded Imaging is used to provide 5 to 10 ..mu..m resolution, broadband (..delta..E/E approx. 0.5) images over a spectral range from 3 keV to 50 keV. Efficient x-ray lensing elements with anticipated submicron resolution are being developed for narrowband (..delta..E/E approx. 10/sup -2/) imaging applications over a spectral range .1 keV to 8 keV. The x-ray lens design is that of a transmission blazed …

Objective of this program is to provide facilities (Federal repositories) in various deep geologic formations at several locations in USA for the safe disposal of commercial radioactive waste from power reactors. The four types of containerized waste are described. The steps for developing the repositories are outlined. (DLC)

Evaluation and calibration measurements were performed on commercial nickel-chromium metal-foil strain gages in a high-magnetic-field (12 T), liquid-helium (4.2 K) environment. The purpose was to fully characterize strain gages for use at cryogenic temperatures in high magnetic fields. In this study, the magnetoresistance of a number of strain gages was measured in three orthogonal directions at mechanical strain levels to 8900 ..mu..m/m. As a result, a unique calibration curve was defined for magnetoresistance strain errors that is independent of strain level and field direction to 12 T at 4.2 K. A current strain-gage application is the measurement of superconductor mechanical properties. These gages will soon be used in the stress analysis of superconducting fusion magnets during cooldown from ambient temperatures and during operation at 4.2 K with magnetic fields to 12 T.

Gamma-ray spectroscopy measurements have been made on mixed uranium and plutonium oxides in sealed containers to determine the uranium and plutonium enrichment and isotopics. Experimental results obtained using two different methods were in good agreement with the known contents. The first method is applicable to thick samples of freshly reprocessed mixed oxide and determines isotopic abundances from measured absolute gamma-ray intensities. Measurement times depend on plutonium enrichment, but for mixed oxide enriched to 12% in plutonium, the fissionable content can be determined to better than 0.5% in 2 h. The second approach utilizes intensity ratios of selected pairs of gamma-rays to determine plutonium enrichment and uranium and plutonium isotopes. This method requires at least 12 h to determine the plutonium enrichment to an accuracy of 0.5%. However, it cannot be applied until the /sup 238/U daughter activities in the mixed oxide reach equilibrium, which requires at least 5 months after separation. Preliminary conclusions drawn from these two noninvasive and nondestructive measurement techniques, and recommendations for future experiments are discussed.