The time evolution of the amplitude of periodic nanoscale ripple patterns formed on Ar+ sputtered Si(OOl ) surfaces was examined using a recently developed in situ spectroscopic technique. At sufficiently long times, we find that the amplitude does not continue to grow exponentially as predicted by the standard Bradley-Harper sputter rippling model. In accounting for this discrepancy, we rule out effects related to the concentration of mobile species, high surface curvature, surface energy anisotropy, and ion-surface interactions. We observe that for all wavelengths the amplitude ceases to grow when the width of the topmost terrace of the ripples is reduced to approximately 25 nm. This observation suggests that a short circuit relaxation mechanism limits amplitude . growth. A strategy for influencing the ultimate ripple amplitude is discussed.

Fine tropospheric aerosols can play important roles in the radiative balance of the atmosphere. The fine aerosols can act directly to cool the atmosphere by scattering incoming solar radiation, as well as indirectly by serving as cloud condensation nuclei. Fine aerosols, particularly carbonaceous soots, can also warm the atmosphere by absorbing incoming solar radiation. In addition, aerosols smaller than 2.5 {micro}m have recently been implicated in the health effects of air pollution. Aerosol-active radioisotopes are ideal tracers for the study of atmospheric transport processes. The source terms of these radioisotopes are relatively well known, and they are removed from the atmosphere only by radioactive decay or by wet or dry deposition of the host aerosol. The progeny of the primordial radionuclide {sup 238}U are of particular importance to atmospheric studies. Uranium-238 is common throughout Earth's crust and decays to the inert gas {sup 222}Rn, which escapes into the atmosphere. Radon-222 decays by the series of alpha and beta emissions shown in Figure 1 to the long-lived {sup 210}Pb. Once formed, {sup 210}Pb becomes attached to aerosol particles with average attachment times of 40 s to 3 min.

The authors present a preliminary analysis and design framework developed for the evaluation and optimization of infrared, Imaging Spatial Heterodyne Spectrometer (SHS) electro-optic systems. Commensurate with conventional interferometric spectrometers, SHS modeling requires an integrated analysis environment for rigorous evaluation of system error propagation due to detection process, detection noise, system motion, retrieval algorithm and calibration algorithm. The analysis tools provide for optimization of critical system parameters and components including : (1) optical aperture, f-number, and spectral transmission, (2) SHS interferometer grating and Littrow parameters, and (3) image plane requirements as well as cold shield, optical filtering, and focal-plane dimensions, pixel dimensions and quantum efficiency, (4) SHS spatial and temporal sampling parameters, and (5) retrieval and calibration algorithm issues.

Optimal selection of array sensors for a chemical sensing application is a nontrivial task. It is commonly believed that "more is better" when choosing the number of sensors required to achieve good chemical selectivity. However, cost and system complexity issues point towards the choice of small arrays. A quantitative array optimization is carried out to explore the selectivity of arrays of partially-selective chemical sensors as a function of array size. It is shown that modest numbers (dozens) of target analytes are completely distinguished with a range of arrays sizes. However, the array selectivity and the robustness against sensor sensitivity variability are significantly degraded if the array size is increased above a certain number of sensors, so that relatively small arrays provide the best performance. The results also suggest that data analyses for very large arrays of partially-selective sensors will be optimized by separately anal yzing small sensor subsets.

The high-strain-rate stress-strain responses of commercial hot-pressed beryllium and rolled-sheet beryllium were studied as a function of orientation in compression and room temperature. Hot-pressed beryllium exhibits isotropic mechanical properties; whereas 16:1 rolled sheet was highly anisotropic. Rolled sheet displayed a factor of two difference in strength between the thickness and in-plane (lowest) directions. Twinning is a key deformation mechanism at high rates.

We have discussed two aspects of creating high integrity software that greatly benefit from the availability of transformation technology, which in this case is manifest by the requirement for a sophisticated backtracking parser. First, because of the potential for correctly manipulating programs via small changes, an automated non-procedural transformation system can be a valuable tool for constructing high assurance software. Second, modeling the processing of translating data into information as a, perhaps, context-dependent grammar leads to an efficient, compact implementation. From a practical perspective, the transformation process should begin in the domain language in which a problem is initially expressed. Thus in order for a transformation system to be practical it must be flexible with respect to domain-specific languages. We have argued that transformation applied to specification results in a highly reliable system. We also attempted to briefly demonstrate that transformation technology applied to the runtime environment will result in a safe and secure system. We thus believe that the sophisticated multi-lookahead backtracking parsing technology is central to the task of being in a position to demonstrate the existence of HIS.

Mission critical applications of MEMS devices require knowledge of the distribution in their material properties and long-term reliability of the small-scale structures. This project reports on a new testing program at Sandia to quantify the strength distribution using samples that reflect the dimensions of critical MEMS components. The strength of polysilicon fabricated with Sandia's SUMMiT 4-layer process was successfully measured using samples with gage sections 2.5 {micro}m thick by 1.7 {micro}m wide and lengths of 15 and 25 {micro}m. These tensile specimens have a freely moving pivot on one end that anchors the sample to the silicon die and prevents off axis loading during testing. Each sample is loaded in uniaxial tension by pulling laterally with a flat tipped diamond in a computer-controlled Nanoindenter. The stress-strain curve is calculated using the specimen cross section and gage length dimensions verified by measuring against a standard in the SEM. The first 48 samples had a means strength of 2.24 {+-} 0.35 GPa. Fracture strength measurements grouped into three strength levels, which matched three failure modes observed in post mortem examinations. The seven samples in the highest strength group failed in the gage section (strength of 2.77 {+-} 0.04 GPa), the moderate strength …

Scenario development has two primary purposes in the design and documentation of post-closure performance assessments in a regulatory setting. First, scenario development ensures a sufficiently comprehensive consideration of the possible future states of the system. Second, scenario development identifies the important scenarios that must be considered in quantitative analyses of the total system performance assessment (TSPA). Section 2.0 of this report describes the scenario development process. Steps in the process are described in Section 2.1, and terms introduced in this section are defined in Section 2.2. The electronic database used to document the process is described in Section 3, and Section 4 provides a summary of the current status of the YMP scenario development work. Section 5 contains acknowledgments, and Section 6 contains a list of the references cited.

We present experimented results directed at understanding the growth and structure of metallic barrier layer and interconnect films. Numerical simulation results associated with this experimental work are presented in an accompanying paper in these proceedings. Here, thin films of Al, Ti, Cu and Ta have been grown by magnetron sputtering onto oxidized Si substrates. Using a specially-constructed substrate holder, the orientation of the substrate with respect to the growth direction was varied from horizontal to vertical. Films were grown at both low and high argon pressure; in the case of Ta, the cathode power was varied as well. The film structure and in particular the surface roughness was measured by X-ray reflectance and also by atomic force microscopy. We find that the surface roughness increases markedly with orientation angle in the case of Ta and Cu films, and in Ti films grown at high argon pressure. At low pressure, however, the Ti film surface roughness remains constant for all substrate orientations. No variation in roughness with either orientation angle or argon pressure was observed in the Al films. These results suggest that, under certain circumstances, shadowing effects and/or grain orientation (i.e., texture) competition during growth can give rise to lower …

None

In order to develop an alternative buffer layer architecture using the sol-gel process to produce YBCO (YBa2Cu307+) coated conductors, Yb203 has been chosen as the candidate material. Buffer layers of fi03 were epitaxkdly grown on biaxially textured-Ni (100) substrates by the sol gel process for the first time. The ~03 precursor solution was prepared from an alkoxide sol-gel route in 2-xnetho~ethanol and was deposited on textured-Ni (100) substrates by either spin coating or dip coating methods. The amorphous film was then processed at 1160oC under flowing (96%)MH2(4%) gas mixture for one hour. The fi03 iihn exhibited a strong c-axis orientation on the Ni (100) substrates. The phi and omega scans indicated good in plane and out of plane orientations. The X-ray (222) pde figure showed a cube-on-cube epitaxy. High current YBCO films were grown on the Y&03 sol-gel buffered-Ni substrates.

Application of Executive Order 12898 to risk assessment of highway or rail transport of hazardous materials has proven difficult; the location and conditions affecting the propagation of a plume of hazardous material released in a potential accident are unknown, in general. Therefore, analyses have only been possible in geographically broad or approximate manner. The advent of geographic information systems and development of software enhancements at Sandia National Laboratories have made kilometer-by-kilometer analysis of populations tallied by U.S. Census Blocks along entire routes practicable. Tabulations of total, or racially/ethnically distinct, populations close to a route, its alternatives, or the broader surrounding area, can then be compared and differences evaluated statistically. This paper presents methods of comparing populations and their racial/ethnic compositions using simple tabulations, histograms and Chi Squared tests for statistical significance of differences found. Two examples of these methods are presented: comparison of two routes and comparison of a route with its surroundings.

First-principles total energies of periodic vicinals are used to estimate barriers for Pt-adatom diffusion along straight and kinked steps on Pt(111), and around a corner where straight steps intersect. In all cases studied, hopping diffusion has a lower barrier than concerted substitution. In conflict with simulations of dendritic Pt island formation on Pt(111), hopping from a corner site to a step whose riser is a (111)-micro facet is predicted to be more facile than to one whose riser is a (100).

IMTR is a tremendous undertaking to assess the current state and future needs of Manufacturing Technology R&D. A follow-on project to the roadmaps is the development and populating of a Gap Analysis database containing current R&D abstracts related to the roadmaps' technical elements. Efficiently identifying the R&D projects within scope presents many travails of synthesizing data from across a wide spectrum. Challenges to this project were directly proportional to the lack of single-source data collections.

Information management is moving quickly toward archiving and retrieving documents electronically, so Oak Ridge National Laboratory (ORNL) is taking steps to help its research staff create electronic documents. Declining budgets frequently dictate that authors handle the technicalities of getting published as well as the scientific and technical information that they publish. To help the Laboratory benefit from being the leader in this area, ORNL'S Information Management Section formed a multidisciplinary team to develop, pilot, and implement a Web- based process to register and clear technical documents and to add the fill text of these documents to the Laboratory's Comprehensive Publications and Presentations Registry (CPPR). Making this happen required implementing policy changes to address the new performance measure, acquiring software needed for file conversion, developing Web guidance, and providing training and consulting for ORNL staff.

Epitaxial thin films of the Tl cuprate superconductors Tl{sub 2}Ba{sub 2}CaCu{sub 2}O{sub 8}, Tl{sub 2}Ba{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10}, and TL{sub 0.78}Bi{sub 0.22}Ba{sub 0.4}Sr{sub 1.6}Ca{sub 2}Cu{sub 3}O{sub 9{minus}{delta}} are studied with x-ray photoemission spectroscopy. These data, together with previous measurements in this lab of Tl{sub 2}Ba{sub 2}CuO{sub 6+{delta}} and TlBa{sub 2}CaCu{sub 2}O{sub 7{minus}{delta}}, comprise a comprehensive data set for a comparative study of Tl cuprates with a range of chemical and electronic properties. In the Cu 2p spectra, a larger energy separation between the satellite and main peaks (E{sub s}-E{sub m}) and a lower intensity ratio (I{sub s}/I{sub m}) are found to correlate with higher values of T{sub c}. Analysis of these spectra within a simple configuration interaction model suggests that higher values of T{sub c} are related to low values of the O 2p {r_arrow} Cu 3d charge transfer energy. In the O 1s region, a smaller bond length between Ba and Cu-O planar oxygen is found to correlate with a lower binding energy for the signal associated with Cu-O bonding, most likely resulting from the increased polarization screening by Ba{sup 2+} ions. For samples near optimum doping, maximum T{sub c} is observed to occur when the Tl 4f{sub …

This report describes efforts made at the oak Rklge NatiOnrd Laboratory to design high- efficiency-release targets that simultaneously incorporate the short diffusion lengths, high permeabilities, controllable temperatures, and heat-removal properties required for the generation of useful radioactive ion beam (RIB) intensities for nuclear physics and astrophysics research using the isotope separation on-line (ISOL) technique. Short diffusion lengths are achieved either by using thin fibrous target materials or by coating thin layers of selected target material onto low-density carbon fibers such as reticulated-vitreous-carbon fiber (RVCF) or carbon-bonded-carbon fiber (CBCF) to form highly permeable composite target matrices. Computational studies that simulate the generation and removal of primary beam deposited heat from target materials have been conducted to optimize the design of targetheat-sink systems for generating RIBs. The results derived from diffusion release-rate simulation studies for selected targets and thermal analyses of temperature distributions within a prototype targetlheat-sink system subjected to primary ion beam irradiation will be presented in this report.

We created three models to represent a comprehensive knowledge model: · Stages of Knowledge Management Model (Forrester) · Expanded Life-Cycle Information Management Model · Organizational Knowledge Management Model. In building a series of models, we started with an attempt to create a graphical model that illustrates the ideas outlined in the Forrester article (Leadership Strategies, Vol. 3, No. 2, November/December 1997). We then expanded and detailed a life-cycle model. Neither of these effectively reflected how to manage the complexities involved in weaving local, enterprise, and global information into an easily navigated resource for end users. We finally began to synthesize these ideas into an Organizational Knowledge Management Model. This model acknowledges the relevance of life-cycle management for different granularities of information collections and places it in the context of the integrating infrastructure needed to assist end users.

We have designed a new class of cyclic siloxane compounds that behave as sol-gel systems when ring open polymerized using a hydroxide base. These monomers polymerize through chain growth polymerization. unlike conventional alkoxysilane sol-gel precursors, to form sol-gel polymers. They do not require solvent or water for polymerization, show no visible shrinkage or cracking during polymerization and are thermally stable. We have successfully utilized these materials in encapsulation of microelectronics. Current efforts are focused toward expanding this family of ROP monomers and optimization of their mechanical properties.

This project used advanced reservoir characterization tools, including the pulsed acoustic cased-hole logging tool, geologic three-dimensional (3-D) modeling software, and commercially available reservoir management software to identify sands with remaining high oil saturation following waterflood. Production from the identified high oil saturated sands was stimulated by recompleting existing production and injection wells in these sands using conventional means as well as a short radius redrill candidate.

The objectives of the pilot study were to investigate the limitations of the technique for imaging the presence, extent, and boundaries of the low-resistance intervals and associated carbonate sediments.

This report details testing performed to determine the radiation stability of the calixarene and Cs-3 modifier solvent system.

This report describes the results of the Savannah River Technology Center (SRTC) program to address bubble gas release potential as requested by Concentration, Storage and Transfer Engineering. Researchers from the Waste Processing Technology Section (WPTS) and Immobilization Technology Section (ITS) contributed to the results presented.

As a follow-up to a bench-top experiment (1), the Savannah River Technology Center (SRTC) at the Savannah River Site (SRS) carried out a full-scale test of a "large-diameter" bubbler (LDB) to measure liquid-level and density in high yield stress slurries. The test was the final step in a process to find an instrument that could effectively and economically operate in the existing mixing tank environments. Positive results would lead to implementation of the LDB. This new bubbler replaced two inadequate instruments: an expensive technology, a Holledge probe, which needed replacing twice a year and "standard bubblers," which plugged in as little as four hours of operation. Three LDBs, at different depths, were tested under highly prototypic conditions from November 27, 1996, to January 23, 1997, using the full-scale test facilities at SRS. The instruments were subjected to 58 days of slurry operation; 14 days of which the slurry was brought to boiling temperatures. The results showed that the LDBs (6.7 cm inside diameter) operated successfully by not plugging with the glass-frit ladened slurry, which was maintained at a minimum temperature of 50 degrees C and at approximatley 102 degrees C during days of boiling. A recommendation was made to implement …