The test obtective for April was to evaluate sodium thiosulfate in limestone scrubber slurry as inhibitor of sulfite oxidation. The resulting effect on saturation levels of calcium sulfate (CaSO/sub 4/.2 H/sub 2/O; gypsum) and scaling in the system was of prime importance. As an antioxidant, S/sub 2/O/sub 3//sup =/ functions as a scale inhibitor by reducing SO/sub 4//sup =/, a known scale former. To meet the test objective, the scrubber was operated in a scaling mode as a base case; finally, the changes resulting from addition of sodium thiosulfate were evaluated. Train 100 was operated at two pH levels and with low and high sulfur coal in April. Because of several delays explained below, only base cases were completed in April.

Numerical analysis tools are used to characterize the fields reradiated by cultural scatterers like powerlines, pipelines and fences. These fields are then compared to the returns expected from deeply buried targets and suggestions are made for methods to identify and remove cultural noise from survey data.

An improved collecting apparatus for small aquatic or airborne organisms such as plankton, larval fish, insects, etc. The improvement constitutes an apertured removal container within which is retained a collecting bag, and which is secured at the apex of a conical collecting net. Such collectors are towed behind a vessel or vehicle with the open end of the conical net facing forward for trapping the aquatic or airborne organisms within the collecting bag, while allowing the water or air to pass through the apertures in the container. The container is readily removable from the collecting net whereby the collecting bag can be quickly removed and replaced for further sample collection. The collecting bag is provided with means for preventing the bag from being pulled into the container by the water or air following therethrough.

A secondary, high temperature electrochemical cell especially adapted for lithium alloy negative electrodes, transition metal chalcogenide positive electrodes and alkali metal halide or alkaline earth metal halide electrolyte is disclosed. The cell is held within an elongated cylindrical container in which one of the active materials is filled around the outside surfaces of a pluraity of perforate tubular current collectors along the length of the container. Each of the current collector tubes contain a concentric atubular layer of electrically insulative ceramic as an interelectrode separator. The active material of opposite polarity in elongated pin shape is positioned longitudinally within the separator layer. A second electrically conductive tube with perforate walls can be swagged or otherwise bonded to the outer surface of the pin as a current cllector and the electrically insulative ceramic layer can be coated or otherwise layered onto the outer surface of this second current collector. Alternatively, the central pin electrode can include an axial core as a current collector.

A reusable system is described for removably attaching the upper end of a nuclear reactor duct tube to the lower end of a nuclear reactor fuel assembly handling socket. A transition ring, fixed to the duct tube's upper end, has an interior-threaded section with a first locking hole segment. An adaptor ring, fixed to the handling socket's lower end has an outside-threaded section with a second locking hole segment. The inside and outside threaded sections match and can be joined so that the first and second locking hole segments can be aligned to form a locking hole. A locking ring, with a locking pin, slides over the adaptor ring so that the locking pin fits in the locking hole. A swage lock or a cantilever finger lock is formed from the locking cup collar to fit in a matching groove in the locking ring to prevent the locking ring's locking pin from backing out of the locking hole.

This paper discusses some of the general difficulties and problems encountered during the development of the technology of superconductors and superconducting magnets for fusion and expresses some personal concerns.

Advanced cooling concepts that permit the design of water cooled heat exchangers for use as calorimeters and beam dumps for advanced neutral beam injection systems were evaluated. Water cooling techniques ranging from pool boiling to high pressure, high velocity swirl flow were considered. Preliminary performance tests were carried out with copper, inconel and molybdenum tubes ranging in size from 0.19 to 0.50 in. diameter. Coolant flow configurations included (1) smooth tube/straight flow, (2) smooth tube with swirl flow created by tangential injection of the coolant, and (3) axial flow in internally finned tubes. Additionally, the effect of tube L/D was evaluated. A CO/sub 2/ laser was employed to irradiate a sector of the tube exterior wall; the laser power was incrementally increased until burnout (as evidenced by a coolant leak) occurred. Absorbed heat fluxes were calculated by dividing the measured coolant heat load by the area of the burn spot on the tube surface. Two six element thermopiles were used to accurately determine the coolant temperature rise. A maximum burnout heat flux near 14 kW/cm/sup 2/ was obtained for the molybdenum tube swirl flow configuration.

A study of fission suppressed blankets for the tandem mirror not only showed such blankets to be feasible but also to be safer than fissioning blankets. Such hybrids could produce enough fissile material to support up to 17 light water reactors of the same nuclear power rating. Beryllium was compared to /sup 7/Li for neutron multiplication; both were considered feasible but the blanket with Li produced 20% less fissile fuel per unit of nuclear power in the reactor. The beryllium resource, while possibly being too small for extensive pure fusion application, would be adequate (with carefully planned industrial expansion) for the hybrid because of the large support ratio, and hence few hybrids required. Radiation damage and coatings for beryllium remain issues to be resolved by further study and experimentation.

Strict limitations on the emission of H/sub 2/S from new geothermal power plants in The Geysers area of northern California have been imposed by Lake and Northern Sonoma County Air Pollution Control Districts. Lake County, under new source review rules, has stipulated that specific technologies shall be utilized to limit H/sub 2/S emissions to 5 lb/h as a condition for determination of compliance. The status of these technologies as well as other ongoing technology development efforts to conserve steam and abate H/sub 2/S are evaluated. Although projections indicate that it may be possible to meet the 5 lb/h limit, there is no firm assurance of achievement at this time because of the unproven, full-scale performance status of some key technologies specified by the air pollution control districts.

The Supervisory Control and Diagnostics System for the Mirror Fusion Test Facility is an event driven system; tasks that handle specific events are active only when those events occur. One method of monitoring and generating events is the data base notification facility; a task can request that it be loaded and started by the dbms if a data element is touched or goes outside of a specified range. The motivations for this facility (along with an example of its use and some specifics regarding how it is done) are presented.

A modified Voitenko compressor generated a Mach-130 air shock in an outlet pipe open to the atmosphere. Fiber optics transmitted luminosity associated with propagation of the air shock to an external display board, which was scanned with a high-speed streaking camera. We describe the computerized microdensitometer scanning technique for converting the film records to pseudo-3D, isodensity, and density profiles. The isodensity contours can be displayed using different colors to facilitate analysis. This technique can achieve resolutions of 1 ns and 2 ..mu..m. We give examples of the pseudo-3D, isodensity, and density profile plots for the experiment. The microdensitometer output was digitized for input to data display programs run on a CDC 7600. These results were used to provide submicrosecond accuracy for shock propagation over a 5 m of the outlet pipes. In addition, we obtained information about gas flow behind the shock front. Other current or possible applications for the technique are measurement of: target implosion in laser fusion, flash x-ray data in hydrodynamic and ballistic experiments, temperature profiles for high energy (> 10/sup 5/ K) gas dynamics, and dynamic events in weapons testing.

This project involved the construction of a fireplace to heat a commercial building. The project was successful in that it demonstrated that wood could be used to heat a commercial building in a properly constructed fireplace.

The TMX experiment proved that axial confinement of central-cell ions is improved ninefold by the electrostatic potential of end-cell plasmas. The TMX Upgrade task is to improve this confinement further. This paper discusses the injector system aspects of the TMX Upgrade.

A subkilovolt spectrometer has been produced to permit high-energy-resolution, time-dependent x-ray intensity measurements. The diffracting element is a curved mica (d = 9.95A) crystal. To preclude higher order (n > 1) diffractions, a carbon x-ray mirror that reflects only photons with energies less than approx. 1.1 keV is utilized ahead of the diffracting element. The nominal energy range of interest is 800 to 900 eV. The diffracted photons are detected by a gold-surface photoelectric diode designed to have a very good frequency response, and whose current is recorded on an oscilloscope. A thin, aluminium light barrier is placed between the diffracting crystal and the photoelectric diode detector to keep any uv generated on or scattered by the crystal from illuminating the detector. High spectral energy resolution is provided by many photocathodes between 8- and 50-eV wide placed serially along the diffracted x-ray beam at the detector position. The spectrometer was calibrated for energy and energy dispersion using the Ni L..cap alpha../sub 1/ /sub 2/ lines produced in the LLNL IONAC accelerator and in third order using a molybdenum target x-ray tube. For the latter calibration the carbon mirror was replaced by one surfaced with rhodium to raise the cut-off energy …

The point code TANDEM has been used to survey the range of plasma parameters which can be attained in MFTF-B. The code solves for the electron and ion densities and temperatures in the central cell, yin-yang, barrier, and A-cell regions as well as the plasma potential in each region. In these studies, the A-cell sloshing ion beams were fixed while the neutral beams in the yin-yang and central cell, the gas feed in the central cell, and the applied ECRH power ..beta.., central cell ion density and temperature, and the confining potential are discussed.

The objective of this research is to investigate the technical feasibility of producing solar-cell-quality sheet silicon to meet the DOE 1986 cost goal of 70 cents/watt. The silicon-on-ceramic approach is to coat a low-cost ceramic substrate with large-grain polycrystalline silicon by unidirectional solidification of molten silicon. Results are reported. A new silicon-coating system, SCIM-II, was designed and constructed. A design strategy to avoid buckling and breaking of substrates has been formulated, implemented, and verified. Detailed thermal modeling of the heating and cooling zones has been performed, and the results have been compared with experiment. A number of modifications have been made in SCIM-II to implement the strategy to minimize thermal stress and to improve reproducibility of coating conditions. Dip-coating has been continued in order to supply material for cell fabrication, since impure carbon parts have been used in the SCIM-coater while changes were still being made. The best cell had a total-area efficiency of 10.5% (AM1, AR) for a cell area of 5 cm/sup 2/. The highest efficiencies were produced with a PH/sub 3/ diffusion at 850/sup 0/C, followed by a slow cooldown at about 5/sup 0/C/min. Theoretical modeling of SOC solar cells shows that present cell performance is limited …

An important loss process in CTR plasmas is the process of dielectronic recombination, which proceeds via autoionizing states. At this date, however, this problem is not fully understood, largely because of the nearly complete lack of fundamental atomic data on high excited autoionizing states. In this document, we outline the continuation of a program to investigate the properties of autoionizing states of alkaline earth metals by means of a novel laser excitation technique developed at SRI. This approach will allow us to study, for the first time, autoionizing states of arbitrary n, and l in a controlled environment. Specifically, we plan to measure autoionization rates and branching ratios as a function of n and l and the effects of electric fields. These experiments should yield the basic atomic data, autoionization rates, required as inputs to sophisticated model calculations of dielectronic recombination rates.

The status for related beneficial uses including agriculture, greenhousing, and geothermal wetlands is presented. Data published for the geothermal fluids found in areas of China have been examined and compared with the geothermal fluids used in the agriculture evaluations in the United States. This comparison indicates that the geothermal fluids found in parts of China are similar to those used in the US agriculture experiments. Greenhousing is addressed largely from the standpoint of hardware systems and technology being employed or being proposed in the United States.

The large potentials and potential gradients in tandem mirrors have several effects. Some of these are discussed, together with supporting data from TMX. These include: azimuthal averaging by the E x B rotation, reduction of radial outward drifts (from high order multipoles) by the rapid E x B azimuthal velocity, neoclassical-resonant diffusion, Joule heating of central cell ions due to non-ambipolar transport in the radial electric field, low frequency instabilities, and differences between the details of the electron behavior and theory.

TMX experimental data on ambipolar potential control and on the accompanying electrostatic confinement are reported. New results on the radial dependence of the central-cell confining potential are given. Radial and axial particle losses as well as scaling of the central-cell axial confinement are discussed.

This report documents the technical evaluation of the adequacy of the station electric distribution system voltages for the R.E. Ginna Nuclear Power Station, Unit 1. The evaluation is to determine if the onsite distribution system, in conjunction with the offsite power sources, has sufficient capacity to automatically start and operate all Class 1E loads within the equipment voltage ratings under certain conditions established by the Nuclear Regulatory Commission. The analysis submitted demonstrates that acceptable voltages will be supplied to the Class 1E equipment under worst case conditions.

The reservoir models used to perform the drawdown and buildup pressure analyses consist of analytic forms in lieu of the finite difference or numeric simulator types. Analytic models are derived from solutions of the diffusion equation which relate a pressure response with time and distance in the reservoir for a specified flow system. Solutions of the diffusion equation are obtained through mathematical methods such as Laplace transforms, Fourier transforms, Neuman's product techniques and Green's functions. Before an analytic solution is derived, the diffusivity equation is expressed in terms of dimensionless potential (m{sub D}), dimensionless distance (r{sub D}) and dimensionless time (t{sub D}). For the cylindrical coordinate case, the diffusivity equation in dimensionless form for a geopressured system is given.

The mechanical and transport properties and characteristics of rock samples obtained from DOW-DOE L.R. SWEEZY NO. 1 TEST WELL at the Parcperdue Geopressure/Geothermal Site have been investigated in the laboratory. Elastic moduli, compressibility, uniaxial compaction coefficient, strength, creep parameters, permeability, acoustic velocities (all at reservoir conditions) and changes in these quantities induced by simulated reservoir production have been obtained from tests on several sandstone and shale samples from different depths. Most important results are that the compaction coefficients are approximately an order of magnitude lower than those generally accepted for the reservoir sand in the Gulf Coast area and that the creep behavior is significant. Geologic characterization includes lithological description, SEM micrographs and mercury intrusion tests to obtain pore distributions. Petrographic analysis shows that approximately half of the total sand interval has excellent reservoir potential and that most of the effective porosity in the Cib Jeff Sand is formed by secondary porosity development.

Twelve flow tests were made on the L. R. Sweezy No. 1 well. Short-term tests, Flow Test No.1 through Flow Test No.4 were designed to estimate formation properties and were conducted for drawdown periods measured in hours. Intermediate-term tests, Flow Test No.5 through Flow Test No.8, were for a few days and were designed to test for reservoir boundaries. Long-term tests, Flow Test No.9 through Flow Test No.12, were designed for drawdown periods of about 60 days in order to examine the depletion behavior of the reservoir.