The Sudbury Neutrino Observatory (SNO) used an array of {sup 3}He proportional counters to measure the rate of neutral-current interactions in heavy water and precisely determined the total active ({nu}{sub x}) {sup 8}B solar neutrino flux. This technique is independent of previous methods employed by SNO. The total flux is found to be 5.54{sub -0.31}{sup +0.33}(stat){sub -0.34}{sup +0.36}(syst) x 10{sup 6} cm{sup -2}s{sup -1}, in agreement with previous measurements and standard solar models. A global analysis of solar and reactor neutrino results yields {Delta}m{sup 2} = 7.94{sub -0.26}{sup +0.42} x 10{sup -5} eV{sup 2} and {theta} = 33.8{sub -1.3}{sup +1.4} degrees. The uncertainty on the mixing angle has been reduced from SNO's previous results.

The equilibrium of an infinitely long, strongly magnetized, non-neutral plasma confined in a Penning-Malmberg trap with an additional mirror coil has been solved analytically [J. Fajans, Phys. Plasmas 10, 1209 (2003)] and shown to exhibit unusual features. Particles not only reflect near the mirror in the low field region, but also may be weakly trapped in part of in the high field region. The plasma satisfies a Boltzmann distribution along field lines; however, the density and the potential vary along field lines. Some other simplifying assumptions were employed in order to analytically characterize the equilibrium; for example the interface region between the low and high field regions was not considered. The earlier results are confirmed in the present study, where two-dimensional particle-in-cell simulations are performed with the Warp code in a more realistic configuration with an arbitrary (but physical) density profile, realistic trap geometry and magnetic field. A range of temperatures and radial plasma sizes are considered. Particle tracking is used to identify populations of trapped and untrapped particles. The present study also shows that it is possible to obtain local equilibria of non-neutral plasmas using a collisionless PIC code, by a scheme that uses the inherent numerical collisionality as …

In 2001, under DOE's Superconductivity Partnership Initiative (SPI), E. I. du Pont de Nemours & Co. (Dupont) was awarded a cost-share contract to build a fully functional full-scale model high temperature superconducting reciprocating magnet unit specifically designed for the koalin clay industry. After competitive bidding, American Superconductor (AMSC) was selected to provide the coil for the magnet. Dupont performed the statement of work until September 2004, when it stopped work, with the concurrence of DOE, due to lack of federal funds. DOE had paid all invoices to that point, and Dupont had provided all cost share. At this same time, Dupont determined that this program did not fit with its corporate strategies and notified DOE that it was not interesting in resuming the program when funding became available. AMSC expressed interest in assuming performance of the Agreement to Dupont and DOE, and in March 2005, this project was transferred to AMSC by DOE amendment to the original contract and Novation Agreement between AMSC and Dupont. Design drawings and some hardware components and subassemblies were transferred to AMSC. However, no funding was obligated by DOE and AMSC never performed work on the project. This report contains a summary of the work …

Recent advances in very-high-energy (VHE) gamma-ray astronomy have opened a new observational window on the physics of pulsars. The high sensitivity of current imaging atmospheric Cherenkov telescopes, and in particular of the H.E.S.S. array, has already led to the discovery of about a dozen VHE-emitting pulsar wind nebulae (PWNe) and PWN candidates. These include the plerions in the composite supernova remnants MSH 15-52, G21.5-0.9, Kes 75, and Vela, two sources in the Kookaburra, and the nebula of PSR B1823-13. This VHE emission is generally interpreted as inverse Compton emission from the relativistic electrons and positrons accelerated by the pulsar and its wind; as such, it can yield a more direct spatial and spectral view of the accelerated particles than can be inferred from observations of their synchrotron emission. The VHE-emitting PWNe detected by the H.E.S.S. telescopes are reviewed and the implications for pulsar physics discussed.

None

Improved nuclear analysis, including the treatment of resonance and spatial self-shielding, coupled with an optimization procedure, has resulted in an improved performance estimate for the molten salt blanket. Net U-233 breeding ratio ranges between 0.58 and 0.63, and blanket energy multiplication ranges between 1.8 and 1.9.

A single electrostatic wave in a magnetoplasma causes stochastic ion motion in several physically different situations. Various magnetic fields (uniform, tokamak, and mirror) and various propagation angles with respect to the field have been studied. A brief review of this work shows that all situations can be understood using the concept of overlapping resonances. Analytical calculations of the wave amplitude necessary for stochasticity have been carried out in some cases and compared with computer and laboratory experiments. In the case of an axisymmetric mirror field the calculations predict stochastic motion of ions with energy below a threshold that depends weakly on the wave amplitude and on the scale lengths of the magnetic field. Studies with an azimuthally asymmetric field show that the asymmetry causes substantial changes in the motion of some ions.

A safety analysis was performed to determine if normal operations and/or potential accidents at the 850 Firing Facility at Site 300 could present undue hazards to the general public, personnel at Site 300, or have an adverse effect on the environment. The normal operations and credible accidents that might have an effect on these facilities or have off-site consequences were considered. It was determined by this analysis that all but one of the hazards were either low or of the type or magnitude routinely encountered and/or accepted by the public. The exception was explosives, which was classified as a moderate hazard per the requirements given in DOE Order 5481.1A. This safety analysis concluded that the operation at this facility will present no undue risk to the health and safety of LLNL employees or the public.

A brief parametric survey of the x-ray characteristics of a gold micro-disk irradiated at 3 x 10/sup 14/ watt/cm/sup 2/ by a 1 nsec Nd-glass laser pulse has been provided as an example of a laser generated bright x-ray source. It was shown that a simple phenomenological model of the laser generated x-ray source as a microscopic equilibrium plasma radiating as a blackbody for a finite time determined by its hydrodynamic disassembly and radiation losses, serves to provide an adequate approximation to the x-ray characteristics of such sources. The current state of x-ray microscopy within the LLL laser fusion program was briefly reviewed. Kirpatrick--Baez grazing incidence reflection x-ray microscopes are being used to provide 3 to 5 ..mu..m resolution, broadband images (..delta..E/E approx. 0.3) over a spectral range from .6 keV to 3.5 keV. Zone Plate Coded Imaging is used to provide 5 to 10 ..mu..m resolution, broadband (..delta..E/E approx. 0.5) images over a spectral range from 3 keV to 50 keV. Efficient x-ray lensing elements with anticipated submicron resolution are being developed for narrowband (..delta..E/E approx. 10/sup -2/) imaging applications over a spectral range .1 keV to 8 keV. The x-ray lens design is that of a transmission blazed …

A modified Voitenko compressor generated a Mach-130 air shock in an outlet pipe open to the atmosphere. Fiber optics transmitted luminosity associated with propagation of the air shock to an external display board, which was scanned with a high-speed streaking camera. We describe the computerized microdensitometer scanning technique for converting the film records to pseudo-3D, isodensity, and density profiles. The isodensity contours can be displayed using different colors to facilitate analysis. This technique can achieve resolutions of 1 ns and 2 ..mu..m. We give examples of the pseudo-3D, isodensity, and density profile plots for the experiment. The microdensitometer output was digitized for input to data display programs run on a CDC 7600. These results were used to provide submicrosecond accuracy for shock propagation over a 5 m of the outlet pipes. In addition, we obtained information about gas flow behind the shock front. Other current or possible applications for the technique are measurement of: target implosion in laser fusion, flash x-ray data in hydrodynamic and ballistic experiments, temperature profiles for high energy (> 10/sup 5/ K) gas dynamics, and dynamic events in weapons testing.

A safety analysis was performed to determine if normal operations and/or potential accidents at the 804 and 845 Firing Facilities at Site 300 could present undue hazards to the general public, peronnel at Site 300, or have an adverse effect on the environment. The normal operation and credible accident that might have an effect on these facilities or have off-site consequence were considered. It was determined by this analysis that all but one of the hazards were either low or of the type or magnitude routinely encountered and/or accepted by the public. The exception was explosives. Since this hazard has the potential for causing significant on-site and minimum off-site consequences, Bunkers 804 and 845 have been classified as moderate hazard facilties per DOE Order 5481.1A. This safety analysis concluded that the operation at these facilities will present no undue risk to the health and safety of LLNL employees or the public.

We are disIgning a minimum-size Tokamak ignition/Burn Reactor (TIBER II). This design incorporates physics requirements, neutron wall loading and fluence parameters that will make it compatible with a nuclear testing mission. Reactor relevant physics will be tested by using current drive and steady-state operation. Although the design accommodates several current drive options, including neutral beams, the base case uses a combination of lower hybrid and electron-cyclotron radio frequency power. Minimum neutron shielding, compact structures, high magnet-current densities, and remotely maintainable vacuum seals, all contribute to the compact size.

The purpose of this investigation was to evaluate several different cleaning procedures on welds with very low heat inputs. The study evaluated the Oak Ridge Y-12 Plant's chemical cleaning, another type of chemical cleaning, ion cleaning, and diamond-machined cleaning. The results showed that the diamond-machining process provides better weld joint surfaces and sound welds with minimum oxide inclusion and porosity.

A subkilovolt spectrometer has been produced to permit high-energy-resolution, time-dependent x-ray intensity measurements. The diffracting element is a curved mica (d = 9.95A) crystal. To preclude higher order (n > 1) diffractions, a carbon x-ray mirror that reflects only photons with energies less than approx. 1.1 keV is utilized ahead of the diffracting element. The nominal energy range of interest is 800 to 900 eV. The diffracted photons are detected by a gold-surface photoelectric diode designed to have a very good frequency response, and whose current is recorded on an oscilloscope. A thin, aluminium light barrier is placed between the diffracting crystal and the photoelectric diode detector to keep any uv generated on or scattered by the crystal from illuminating the detector. High spectral energy resolution is provided by many photocathodes between 8- and 50-eV wide placed serially along the diffracted x-ray beam at the detector position. The spectrometer was calibrated for energy and energy dispersion using the Ni L..cap alpha../sub 1/ /sub 2/ lines produced in the LLNL IONAC accelerator and in third order using a molybdenum target x-ray tube. For the latter calibration the carbon mirror was replaced by one surfaced with rhodium to raise the cut-off energy …

Consider the problem of testing goodness-of-fit to a specified location-scale family when evidence is to be combined from several independent samples, from populations with possibly different location and scale parameters. The procedure studied is that of computing standardized residuals from each sample and then combining these into one set to be treated essentially as though they came from one sample. It is shown that the limiting distribution of any location-scale invariant goodness-of-fit statistic so applied is precisely the same as for the corresponding one-sample problem. 13 references.

The Emergency Core Cooling System (ECCS) for the LOFT reactor may need to be disabled for modifications or repairs of hardware or instrumentation or for component testing during periods when the reactor system is hot and pressurized, or it may be desirable to enable the ECCS to be disabled without the necessity of cooling down and depressurizing the reactor. LTR 113-47 has shown that the LOFT ECCS can be safely bypassed or disabled when the total core power does not exceed 25 kW. A modified policy involves disabling the automatic actuation of the LOFT ECCS, but still retaining the manual activation capability. Disabling of the automatic actuation can be safely utilized, without subjecting the fuel cladding to unacceptable temperatures, when the LOFT power decays to 70 kW; this power level permits a maximum delay of 20 minutes following a LOCA for the manual actuation of ECCS.

Modifications to the 100-K water plant will be made, under Project CG-775, to increase total process water flow rates to 175,000 gpm or greater. Included in the modifications will be the installation of new pump impellers for the primary and secondary process water pumps located in the 190-K Buildings.

This report describes a research project that was conducted from August 15, 1985 to February 28, 1992. The project was based on the ultrasonic studies of natural and synthetic silicate melts, and the study of Brillouin scattering of synthetic silicates and oxides. Measurements of the compressional wave velocity and attenuation can be established using the ultrasonic methods. Temperature dependences of silicates can be established by the Brillouin scattering. (MB)

Memos, agendas, regional hydrology, and field trip reports are included for the INEL oversight program; they relate to the hydrogeology of INEL and ICPP, and to the cleanup effort at these sites.

Results are reported in two areas: (1) understanding the mechanism of superplasticity in those that show unusual resistance to intergranular cavitation, and (2) understanding the growth of heteroepitaxial films of oxides by CVD (NiO, TiO{sub 2}).

These lecture notes review the LDA-KKR-CPA method for treating the electronic structure and energetics of random alloys and the MF-CF and GPM theories of ordering and phase stability built on the LDA- KKR-CPA description of the disordered phase. Section 2 lays out the basic LDA-KKR-CPA theory of random alloys and some applications. Section 3 reviews the progress made in understanding specific ordering phenomena in binary solid solutions base on the MF-CF and GPM theories of ordering and phase stability. Examples are Fermi surface nesting, band filling, off diagonal randomness, charge transfer, size difference or local strain fluctuations, magnetic effects; in each case, an attempt is made to link the ordering and the underlying electronic structure of the disordered phase. Section 4 reviews calculations of electronic structure of {beta}-phase Ni{sub c}Al{sub 1-c} alloys using a version of the LDA-KKR-CPA codes generalized to complex lattices.

None

During the 0000--0800 shift on August 21, 1960, the delayed neutron monitor on KER Loop 1 indicated a high coolant activity level. Sympathetic responses were also recorded on the Loop 2, 3 and 4 monitors indicating a possible fuel element failure in Loop 1. The KER Reactor began shutdown operations immediately thereafter. The purpose of this report is to summarize the events pertinent to this reactor outage and to discuss the results obtained from coolant and coupon samples taken from Loop 1.

Recent high tank drawdown data obtained at F reactor during periodic high velocity flushes indicated a reduction in flow to the reactor due to building of corrosion products in the high tank discharge lines. The apparent flow reduction at F reactor was verified by conducting a high tank drawdown test. Visual inspection of B, D, and F high tank discharge lines revealed comparable densities of corrosion product buildup, and high tank drawdown data during high velocity flushes at B and D also indicated a reduction in flow. High tank flow rate to the reactor under simulated emergency conditions needed to be accurately determined to establish current backup adequacy. This report presents the results of the tests which were conducted at D reactor on January 20, 1963 and at B reactor on February 11, 1963.