"Tests of a 1/20-scale model of the Fleetwings XBTK-1 airplane have been performed in the Langley 15-foot free-spinning tunnel to determine the trim tendencies of the airplane at attitudes above the stall. The results of the tests indicated that the model would trim longitudinally only in the normal range of angles of attack and that the yaw trim tendencies for such longitudinal trim conditions were normal. Although wide oscillations in yaw were noted for some conditions, they occurred at angles of attack larger than those indicated as possible for longitudinal trim and spin equilibrium" (p. 1).

"In order to determine the aerodynamic effects of an auxiliary belly fuel tank on the Grumman F8F-1 airplane, a wind-tunnel investigation was made on a 1/5 - scale model of the Grumman XF8F-1 airplane. Pitch and yaw tests were made with the model in the cruising and landing configurations for windmilling and take-off power conditions. Tuft studies and static-pressure measurements were also made to determine the flow characteristics in the region of the fuel tank" (p. 1).

"A supplementary investigation has been conducted in the Langley 20-foot free-spinning tunnel on a l/24-scale model of the Grumman F11F-1 airplane to determine the spin and recovery characteristics with alternate nose configurations, the production version and the elongated APS-67 version, with and without empty and full wing tanks. When spins were obtained with either alternate nose configuration, they were oscillatory and recovery characteristics were considered unsatisfactory on the basis of the fact that very slow recoveries were indicated to be possible. The simultaneous extension of canards near the nose of the model with rudder reversal was effective in rapidly terminating the spin" (p. 1).

Memorandum presenting an investigation to determine the static longitudinal and lateral stability of three variations of a flared-skirt-type two-stage missile configuration with three different nose shapes, body cross sections, and skin geometry in the 11-inch hypersonic tunnel. The results of the investigation show that the models with rounded triangular cross sections have a variation of lift, drag, lift-drag ratio, and stability with roll angle.

Report discussing several investigations into the maximum-lift capabilities of aircraft wings at high speeds. Testing of thin unswept and swept wings at subsonic and transonic speeds, thin and thick wings, and the effect of airfoil sections on various airplanes is presented and compared.

Performance data and characteristics of a 16-inch impulse-type supersonic-compressor rotor are presented. The experimental portion of this investigation was conducted in Freon-12. A peak pressure ratio of 3.6 was obtained with an adiabatic efficiency of 0.80 at design conditions. Performance was continuous from impulse operation, at open throttle, to shock-in-rotor operation at the stall condition.

"An investigation has been conducted in the Langley 20-foot free-spinning tunnel of a 1/29-scale model of the Republic XF-91 airplane with a.conventional-tail arrangement installed. Previously, tests were made on the model with a vee tail installed. The erect spin and recovery characteristics of the model were determined for the normal loading with the wing installed at various amounts of incidence. The spin investigation also included inverted-spin tests, spin-recovery-parachute tests, tests with the center of gravity moved rearward, and tests with external fuel tanks added to the model" (p. 1).

An investigation was conducted to determine the effect of electropolishing precision-forged blades and of machining blades from oversize forgings on the engine performance of Nimonic 80 and Nimonic 80A turbine blades. These blades, along with precision-forged blades, were run in a J33-9 turbojet engine. The tests resulted in the following conclusions: (1) Electropolishing of precision-forged blades did not improve engine life relative to the life of nonelectropolished blades. (2) Machining blades from oversize forgings did not improve the engine life of precision-forged blades. (3) The precision-forging and heat-treating practice used in fabricating the blades investigated was such that the surface roughness and oxide penetration was so slight, approximately 0.0005 inch in depth, as to preclude any benefits derived from surface removal by electropolishing or machining.

Report presenting pressure-distribution data for a drooped-nose-fuselage forebody alone and with four canopy shapes mounted on the forebody. Two canopies had the same shape and size rearward of the windshield but one had a flat and one had a v-shaped windshield, and the other two canopies were located at different body sections with smaller maximum cross-sectional areas, higher fineness ratios, and flat windshields. Results regarding the effect of windshield shape, canopy location, Mach number, sideslip, and angle of attack are provided.

Report presenting measurements in a wind tunnel of the static and dynamic-rotary stability derivatives of a model with an unswept wing of low aspect ratio and a high horizontal tail. Tests were conducted at a range of Mach numbers and angles of attack. Results regarding a variety of aerodynamic characteristics are provided.

From Introduction: "In the present investigation, lift, drag, and pitching moment were determined over a Mach number range 0.6 to 1.42. Smooth-water takeoff and landing stability and resistance were investigated. A brief check of the rough-water spray and behavior was also made."

From Summary: "Force characteristics determined from tank tests of a 1/5.78 scale model of a hydro-ski-wheel combination for the Grumman JRF-5 airplane are presented. The model was tested in both the submerged and planing conditions over a range of trim, speed, and load sufficiently large to represent the most probable full-size conditions."

"Experimental results showing the static longitudinal-stability and control characteristics of a model of a fighter airplane employing a low-aspect-ratio unswept wing and an all-movable horizontal tail are presented. The investigation was made over a Mach number range from 0.60 to 0.90 and from 1.35 to 1.90 at a constant Reynolds number of 2.40 million, based on the wing mean aerodynamic chord. Because of the location of the horizontal tail at the tip of the vertical tail, interference was noted between the vertical tail and the horizontal tail and between the wing and the horizontal tail" (p. 1).

"Dynamic--response measurements for various conditions of displacement and rate signal input, sensitivity setting, and simulated hinge moment were made of the three control-surface servo systems of an NAES-equipped remote-controlled airplane while on the ground. The basic components of the servo systems are those of the General Electric Company type G-1 autopilot using electrical signal sources, solenoid-operated valves, and hydraulic pistons. The test procedures and difficulties are discussed" (p. 1).

Tests of a 1/5 scale model of a proposed 153-foot high-speed submarine have been conducted in the Langley full-scale tunnel at the request of the Bureau of Ships, Department of the Navy. The test program included: (1) force tests to determine the drag, control effectiveness, and static stability characteristics for a number of model configurations, both in pitch and in yaw, (2) pressure measurements to determine the boundary-layer conditions and flow characteristics in the region of the propeller, and (3) an investigation of the effects of propeller operation on the model aerodynamic characteristics. In response to oral requests from the Bureau of Ships representatives t hat the basic data obtained in these tests be made available to them as rapidly as possible, this data report has been prepared to present some of the more pertinent results. All test results given in the present paper are for the propeller-removed condition and were obtained at a Reynolds number of approximately 22,300,000 based on model length.

The stator-blade angles in the twelfth through fifteenth stages of a 16-stage axial-flow compressor were increased 3O. The over-all performance of this modified compressor is compared to the performance of the compressor with original blade angles. The matching characteristics of the modified compressor and a two-stage turbine were obtained and compared to those of the compressor with original blade angles and the same turbine.

Ignition delays of a diallylaniline-triethylamine mixture and of triethyl trithioposphite with red fuming nitric acid were measured as a function of combustor dimensions, initial propellant temperature, and initial ambient pressure. Ignition delay increased with exhaust-nozzle diameter. Ignition delay also increased as propellant temperature decreased, but did not vary with initial ambient pressure except with the largest nozzle diameter. A correlation among ignition delay, combustor dimensions, and propellant temperature is presented, and the extension of the correlation to other systems is discussed.

From Summary: "An investigation was conducted in the combustor of a 3000-pound-thrust turbojet engine to determine the altitude performance characteristics of AN-F-58 fuels. Three fuels conforming to AN-F-58 specification were prepared in order to determine the influence of boiling-temperature range and aromatic content on altitude performance. The performance of the three AN-F-58 fuels was compared with the performance of AN-F-48 (grade 100/130) fuel in the range of simulated altitudes from 20,000 to 55,000 feet, corrected engine speeds from 6000 to 12,500 rpm, and flight Mach numbers of 0.2 and 0.6."