From Introduction: "This report presents data from measurements of the flow in a single-stage research compressor, which supports the model of reference 1. A calculated shock technique similar to that of reference 1 is incorporated with these experimental results. Another approach for estimating passage shock loss given a flow rate and blade geometry was reported in reference 2."

Report presenting the results from 20 hours of service operational flying of an instrumented North American F-100A fighter airplane. Results regarding the altitude and Mach number, normal-load factor, airplane attitude, use of controls, rolling motions, pitching motions, yawing motions, vertical-tail loads, horizontal-tail loads, and a comparison with other airplanes are provided.

Report presenting an investigation of three cone-cylinder bodies to obtain boundary-layer-transition data at very low ratios of wall to local stream temperature. Surface finishes at several levels of roughness height were tested. Results regarding the smooth body and rough bodies are provided.

Memorandum presenting an investigation of the performance of a five-stage transonic research compressor with distorted inlet flow. Both overall performance and individual blade-row performance results over a range of compressor speeds and equivalent weight flows were obtained with three circumferential inlet flow-distortion patterns covering annular extents of 60, 120, and 180 degrees. Results regarding compressor-inlet conditions and overall performance and individual blade-row performance are provided.

"A supplementary investigation has been conducted in the Langley 20-foot free-spinning tunnel on a l/24-scale model of the Grumman F11F-1 airplane to determine the spin and recovery characteristics with alternate nose configurations, the production version and the elongated APS-67 version, with and without empty and full wing tanks. When spins were obtained with either alternate nose configuration, they were oscillatory and recovery characteristics were considered unsatisfactory on the basis of the fact that very slow recoveries were indicated to be possible. The simultaneous extension of canards near the nose of the model with rudder reversal was effective in rapidly terminating the spin" (p. 1).

Memorandum presenting an investigation of a double-ramp cascade inlet at Mach number 3.05 in order to determine the penalties associated with decreasing the length of inlets by means of cascades. Total-pressure recovery and profile distortion of the cascade inlet were compared with a similar single-passage inlet that captured the same mass flow.

Report discussing an investigation of a 45 degree swept-back-wing-body combination with flap spoiler ailerons, deflector ailerons, and a spoiler-slot-deflector aileron. The pressures were measured from Mach numbers 0.60 to 1.03 and at various angles of attack.

Memorandum presenting a flight investigation to determine the longitudinal and lateral handling qualities of the Douglas X-3 research airplane in the clean configuration. Static and dynamic stability and control characteristics were determined during trimmed and maneuvering flight at an average altitude of 30,000 feet and over a Mach number range from 0.7 to 1.16.

Memorandum presenting an investigation of the use of low auxiliary horizontal-tail surfaces to alleviate the pitch-up tendency at high lift of an airplane configuration with a T-tail. The basic model had a wing with an aspect ratio of 3, a taper ratio of 0.143, and an unswept 80-percent chord line.

Report presenting an investigation conducted at the 16-foot transonic tunnel to determine the loading characteristics of flap-type ailerons located at inboard, midspan, and outboard positions on a 45 degree sweptback-wing-body combination. Results indicated that the loading over the ailerons was established by the wing-flow characteristics and the loading shapes were irregular in the transonic speed range.

Report presenting a study of the first stage performance characteristics of the two-stage turbine from the J73 turbojet engine. The reduced-chord first-stage turbine operated at a peak brake internal efficiency of over 91 percent at a stage overall pressure ratio of 1.4 and at 90 percent of the design equivalent speed. The unit exhibited high efficiency over a wide range of operating variables.

Report presenting an investigation of a reduced-chord multistage turbine at design speed and various turbine-inlet pressures from 12 to 40 inches of mercury absolute. At each inlet pressure, the turbine was operated over a range of overall turbine total-pressure ratios; turbine-inlet temperature was maintained at 700 degrees R. The results indicated that no appreciable effect on turbine overall performance was observed over the range of turbine-inlet total pressures investigated.

Report presenting an investigation of the transonic flutter characteristics of a cantilevered, aspect-ratio-4, 45 degree sweptback, untapered wing with three different pylon-mounted external-store configurations. An additional study was created during the investigation to find a store configuration with a substantially higher flutter speed than what was obtained with the other two stores. Results regarding general comments, the investigation of store types A and B, node-line survey, and the investigation of store type C are provided.

Memorandum presenting a wind-tunnel investigation of a high-wing airplane with an aspect ratio 6.75 wing with approximately 36 degrees of sweepback in order to determine the lift effectiveness obtainable with trailing-edge blowing flaps in combination with leading-edge slats. Close to theoretical flap effectiveness was obtained with blowing flaps deflected 45, 55, and 65 degrees at low angles of attack. Results regarding the wind tunnel, take-off performance, landing performance, and comparisons with flight data are provided.

Report presenting a wind-tunnel investigation of a high-wing airplane with an aspect ratio 6.75 wing with approximately 36 degrees of sweepback to determine the lift effectiveness obtainable with trailing-edge blowing flaps in combination with leading-edge slats. Flap effectiveness and stability were maintained to high angles of attack by control of leading-edge flow separation with slats. An analysis of the take-off performance, landing performance, and comparisons with flight data are provided.

"Flutter models of the upper and lower vertical tails of an air-to-ground missile have been tested in the Mach number range from 0.5 to 3.0. It was found that the upper surface exhibited more or less conventional flutter behavior throughout the Mach number range, whereas the lower surface experienced a sudden change in flutter mode at a Mach number of about 1.18. This change in flutter mode was accompanied by a decrease of about 50 percent in the density required for flutter to occur" (p. 1).

Report presenting an investigation in the high speed 7- by 10-foot tunnel through a range of Mach numbers to determine the lateral-control and hinge-moment characteristics of a spoiler-slot-deflector configuration on a semispan 35 degree sweptback-wing model. The results indicated that the spoiler-slot-deflector configuration with the ratio of deflector projection to spoiler projection increasing with increasing control projection has good rolling-moment effectiveness throughout the angle of attack range and throughout the high subsonic speed range.

Memorandum presenting an investigation to determine the static longitudinal and lateral stability of three variations of a flared-skirt-type two-stage missile configuration with three different nose shapes, body cross sections, and skin geometry in the 11-inch hypersonic tunnel. The results of the investigation show that the models with rounded triangular cross sections have a variation of lift, drag, lift-drag ratio, and stability with roll angle.

Memorandum presenting a study of two bluff modifications of the TX-28 store in the 27- by 27-inch preflight jet of the Langley Pilotless Aircraft Research Station. Successful releases were made with both stores at near-sea-level conditions with high ejection velocities. Results regarding the Bluff TX-28 and Turnabout TX-28 are provided.

From Introduction: "In the present investigation, lift, drag, and pitching moment were determined over a Mach number range 0.6 to 1.42. Smooth-water takeoff and landing stability and resistance were investigated. A brief check of the rough-water spray and behavior was also made."

Report presenting pressure-distribution data for a drooped-nose-fuselage forebody alone and with four canopy shapes mounted on the forebody. Two canopies had the same shape and size rearward of the windshield but one had a flat and one had a v-shaped windshield, and the other two canopies were located at different body sections with smaller maximum cross-sectional areas, higher fineness ratios, and flat windshields. Results regarding the effect of windshield shape, canopy location, Mach number, sideslip, and angle of attack are provided.

Report presenting measurements in a wind tunnel of the static and dynamic-rotary stability derivatives of a model with an unswept wing of low aspect ratio and a high horizontal tail. Tests were conducted at a range of Mach numbers and angles of attack. Results regarding a variety of aerodynamic characteristics are provided.

Report presenting calculations by the method of characteristics of 2960 boundaries of supersonic axisymmetric free jets exhausting from conically divergent nozzles into still air. The calculations covered a range of jet Mach numbers, a ratio of specific heats of the jet, divergence angles of the nozzle, and jet static-pressure ratios. Results regarding the effect of increasing the static pressure ratio, the simulation of one jet boundary by another, and interpolation and extrapolation of calculated boundaries are provided.

Ignition delays of a diallylaniline-triethylamine mixture and of triethyl trithioposphite with red fuming nitric acid were measured as a function of combustor dimensions, initial propellant temperature, and initial ambient pressure. Ignition delay increased with exhaust-nozzle diameter. Ignition delay also increased as propellant temperature decreased, but did not vary with initial ambient pressure except with the largest nozzle diameter. A correlation among ignition delay, combustor dimensions, and propellant temperature is presented, and the extension of the correlation to other systems is discussed.