"In order to determine the aerodynamic effects of an auxiliary belly fuel tank on the Grumman F8F-1 airplane, a wind-tunnel investigation was made on a 1/5 - scale model of the Grumman XF8F-1 airplane. Pitch and yaw tests were made with the model in the cruising and landing configurations for windmilling and take-off power conditions. Tuft studies and static-pressure measurements were also made to determine the flow characteristics in the region of the fuel tank" (p. 1).

The gust and draft velocities evaluated from acceleration and airspeed-altitude records taken by NACA instruments installed in P-61c airplanes participating in thunderstorm flights 9, 10, and 11 of July 12, 1946, July 17, 1946, and July 18, 1946, respectively, are presented in references 1 and 2 for previous flights. In accordance with a recent discussion with a member of the U.S. Weather Bureau staff, motion-picture records of the pilots' instrument panels for the present flights were inspected to note variations in the readings of a milliammeter used in conjunction with other equipment to indicate ambient air temperature. The inspection indicated that the instrument read zero throughout all traverses.

"A spin-tunnel investigation of a 1/26 scale model of the Douglas XTB2D-1 airplane has been conducted in the Langley 20-foot free-spinning tunnel. The effects of control settings and movements upon the erect- and inverted-spin and recovery characteristics of the model were determined for various loading conditions. Tests were also performed to determine the effects of various tail modifications. The investigation included emergency spin-recovery parachute tests as well as crew-escape and rudder- and elevator-force tests. All tests were performed at an equivalent spin altitude of 20,000 feet" (p. 1).

"The tests reported herein were made for the purpose of determining the high-speed load distribution on the wing of a 3/16 scale model of the Douglas XSB2D-1 airplane. Comparisons are made between the root bending moment and section torsional moment coefficients as obtained experimentally and derived analytically. The results show good correlation for the bending moment coefficients but considerable disagreement for the torsional moment coefficients, the measured moments being greater than the analytical moments. The effects of Mach number on both the bending moment and torsional moment coefficients were small" (p. 1).

"Tests of a 1/20-scale model of the Fleetwings XBTK-1 airplane have been performed in the Langley 15-foot free-spinning tunnel to determine the trim tendencies of the airplane at attitudes above the stall. The results of the tests indicated that the model would trim longitudinally only in the normal range of angles of attack and that the yaw trim tendencies for such longitudinal trim conditions were normal. Although wide oscillations in yaw were noted for some conditions, they occurred at angles of attack larger than those indicated as possible for longitudinal trim and spin equilibrium" (p. 1).

Report presenting the results of testing in the transonic range of four flutter airfoils attached to a freely falling body. Failures of the airfoils were metered and recorded in order to determine the Mach numbers and altitudes of failure.

Tests were made in the Langley 7- by 10-foot tunnel on a 0.182-scale model of an F4U-1 airplane with external stores. This paper is concerned mainly with presenting the data obtained in this investigation and with a comparison of some of these data with flight-test results determining the feasibility of estimating flight buffet Mach number from tunnel data. The results of this investigation indicate that the incremental drag coefficient due to external stores may be used to estimate the maximum Mach number that the F4U-1 airplane may reach in flight when it is equipped with external stores. This estimation is conservative for the five configurations investigated by mounts varying from 0 to 10 percent of the flight limit Mach number. The free-stream tunnel Mach number corresponding to sonic flow over the lower surface of the wing in the region of the store is a good indication of the lower limit of buffet in flight of the F4U-1 airplane when equipped with external stores. The fluctuations of total pressure over the horizontal tail are not sufficiently large (maximum of 1 percent q(sub o) to cause buffeting of the airplane.

The sea-level performance of I-16 turbojet engine at zero ram was investigated to determine the effects of an intake duct, shroud, and tail pipe intended for installation in an XFR-1 airplane. Engine speeds ranged from 8000 to 16,500 rpm for several variations of the intake duct and tail pipes.

"An investigation of the DM-1 Glider, which had approximately triangular plan form, an aspect ratio of 1.8 and a 60 degree sweptback leading edge, has been conducted in the Langley full-scale tunnel. The investigation consisted of the determination of the separate effects of the following modifications made to the glider on its maximum lift and stability characteristics: (a) installation of sharp leading edges over the inboard semispan of the wing, (b) removal of the vertical fin, (c) sealing of the elevon control-balance slots, (d) installation of redesigned thin vertical surfaces, (e) installation of faired sharp leading edges, and (f) installation of canopy" (p. 1).

Report presenting measurements using the NACA wing-flow method of the lift, pitching-moment, and hinge-moment characteristics of a 35 degree sweptback NACA 65-009 airfoil of aspect ratio 3.04 with a full-span 1/4-chord unsealed plain flap. The tests were carried out at a range of Mach numbers, Reynolds numbers, angles of attack, and flap deflections. Variations of lift and pitching moment with angle of attack or flap deflection were approximately rectilinear at all Mach numbers for moderate angles of attack and flap deflections.

Report presenting a flight investigation conducted to establish the heat requirements for ice prevention on aircraft windshields mounted on the forebody of an airplane at several angles. Electrically heated windshields were used in order to provide accurate measuring of heat input to the windshield. Results regarding the quantity of heat provided, amount of water collection, ideal windshield angle, ranges in airplane velocity, and icing conditions are provided.

From experience gained by NACA test pilots in flying at high subsonic Mach numbers and from interpretation of the data obtained, some general precautionary rules for test flying near sonic Mach numbers have been formulated. The reasons for these rules are discussed and observations are made with respect to the hazards arising from undesirable stability and control characteristics which have been noted in test flights of various airplanes. This paper, although written primarily for the attention of test pilots, contains general information of interest to those who are concerned with various phases of flight testing near sonic Mach numbers.

From Summary: "The results of an experimental investigation of an NACA submerged-air-inlet system on a 1/5-scale model of a fighter airplane are presented. Preliminary development tests were conducted to select the optimum entrance configuration. Duct-system total-pressure losses and pressure distributions over the lip and ramp of this air intake were obtained."

The gust and draft velocities from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from August 16, 1947 to August 20, 1947 are presented.

Report presenting an investigation to obtain the pressure distribution over a sharp-nose body of revolution with a circular-arc profile and fineness ratio 6 at transonic speeds using the NACA wing-flow method. Results regarding the variation of pressure coefficient with Mach number, pressure distributions along the body axis, pressure drag, and effects of interference and horizontal gradient are provided.

The gust and draft velocities from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from September 10, 1947 to September 15, 1947, are presented.

Report presenting an investigation to study cowling-spinner combinations based on the NACA 1-series nose inlets and to obtain systemic data for one family of approximately ellipsoidal spinners. 11 of the spinners were also tested in various combinations with 9 NACA open-nose cowlings, which were also tested without spinners. Results regarding flow over spinners, internal flow, external flow over cowling, critical Mach number characteristics, envelope values, and cowling section are provided.

A wind tunnel investigation was conducted to determine the performance of a 4000-pound-thrust axial-flow turbojet engine with a high flow compressor. Pressure altitudes included 5000 to 40000 feet with ram pressure ratios from 1.00 to 1.82. Altitudes included 20000 to 40000 feet and ram pressure ratios from 1.09 to 1.75. A comparison is made between engine performance with high flow and low flow compressors.

Operating characteristics of the 11-stage 4000-pound-thrust axial-flow turbojet engine were determined. A standard compressor and a compressor with the blade angles of the rotor and stator blades increased 5 degrees to obtain greater air flow, were investigated.

Tests were made to determine the loss in exhaust-jet thrust and engine power resulting from the insertion of an exhaust-gas-to-air heat exchanger in a jet-type exhaust stack of an aircraft engine. The thermal performance of the heat exchanger was also determined.

"In the present paper an analysis is made of the compressible-flow variations occurring in heat-exchanger passages. The results of the analysis describe the flow and heating characteristics for which specific flow passages can be treated as segments of generalized flow systems. The graphical representation of the flow variations in the generalized flow systems can then be utilized as working charts to determine directly the pressure changes occurring in any specific flow passage. On the basis of these results, working charts are constructed to handle the case of air heated at constant wall temperature under turbulent-flow conditions" (p. 1).

Report presenting the results of lift, drag, and pitching-moment measurements on a model of the Douglas D-558-2 airplane at a range of angles of attack and Mach numbers. The model was also tested with two different sets of chordwise fences in order to investigate their effects on force and moment characteristics at high speeds.

"An investigation has been conducted in the Langley 20-foot free-spinning tunnel of a 1/29-scale model of the Republic XF-91 airplane with a.conventional-tail arrangement installed. Previously, tests were made on the model with a vee tail installed. The erect spin and recovery characteristics of the model were determined for the normal loading with the wing installed at various amounts of incidence. The spin investigation also included inverted-spin tests, spin-recovery-parachute tests, tests with the center of gravity moved rearward, and tests with external fuel tanks added to the model" (p. 1).

Report presenting an approximate method for calculating the interference pressure distribution at zero lift of a symmetrical sweptback wing mounted on a circular cylindrical body with the chord plane of the wing passing through the axis of the body. An example is provided using a circular cylindrical body and an untapered wing with 60 degrees of sweepback.