A series of flight tests have been made at the Langley Flight Research Division at the request of the Bureau of Aeronautics, Department of the Navy, to determine the flying qualities of the Grumman F8F-1 air- plane. This paper presents the test results necessary to determine the longitudinal stability and control characteristics end the stalling characteristics. The range of Mach numbers covered in this investigation was approximately 0.10 to 0.62, and no attempt was made to investigate compressibility effects at higher Mach numbers.

Report presenting an investigation to determine some of the effects of lip geometry on drag and pressure recovery of a normal-shock nose inlet. Lip bluntness, lip camber, and forebody angle were all explored as possible variables. Total-pressure recoveries, external drags, duct total-pressure distributions, lip and forebody pressure distributions, and Schileren photographs are provided.

Memorandum presenting the results of a wind-tunnel investigation of the low-speed aerodynamic characteristics of two semispan horizontal tails with unswept and 35 degree sweptback plan forms. The two models had an aspect ratio of 4.5, taper ratio of 0.5, and an NACA 64A010 airfoil section. Test results are presented with and without standard roughness applied to their leading edges and with sealed and unsealed radius-nose elevators.

Report presenting an investigation in the supersonic wind tunnel on a cylindrical-shroud ejector. Data were obtained at several weight-flow ratios, primary pressure ratios, and free-stream Mach numbers. The results indicate that there was no effect of free-stream Mach number on the pumping characteristics of an ejector of this type. Results regarding the internal characteristics and external characteristics are provided.

From Introduction: "The combustor efficiency, combustor total-pressure ratio, combustor-outlet total pressure, combustor-inlet Mach number, and specific fuel consumption are presented. The effect of combustor length on efficiency and the effect of pilot operating conditions burning limits are also presented."

From Summary: "The results of altitude-wind-tunnel tests conducted to determine the performance of an axial-flow-type 4000-pound-thrust turbojet engine for a range of pressure altitudes from 5000 to 40,000 feet and ram pressure ratios from 1.02 to 1.86 are presented and the experimental and analytical methods employed are discussed. By means of suitable generalizing factors applied to the measured performance data, curves were obtained from which the engine performance at any altitude for a given ram pressure ratio can be estimated. The data presented include the windmilling drag characteristics of the turbojet engine for the ranges of altitudes and ram pressure ratios covered by the performance data."

A flight test has been conducted to determine the longitudinal stability and control,characteristics of a 0.133-scale model of the Consolidated Vultee XFY-1 airplane without propellers for the Mach number range between 0.73 and 1.19.

"A supplementary investigation was conducted in the Langley 20-foot free-spinning tunnel on a 1/24-scale model of the Grumman F9F-6 airplane. The primary purpose of the investigation was to reevaluate the spin-recovery characteristics of the airplane in view of the fact that the ailerons had been eliminated from the flaperon-aileron lateral control system of the airplane. A spin-tunnel investigation on a model of the earlier version of the F9F-6 airplane had indicated that use of ailerons with the spin (stick right in a right spin) was essential to insure recovery" (p. 1).

Report presenting an investigation to determine the effect of conical camber on the drag due to lift and on the static longitudinal, lateral, and directional stability characteristics of an aspect-ratio-3, 45 degree sweptback wing in combination with a streamline body. The addition of conical camber to the basic wing reduced the drag due to lift at moderate and large lift coefficients and increased the maximum lift-drag ratios.

"An investigation of the altitude performance characteristics of an Allison J35-A-17 turbojet engines have been conducted in an altitude chamber at the NACA Lewis laboratory. Engine performance was obtained over a range of altitudes from 20,000 to 60,000 feet at a flight Mach number of 0.62 and a range of flight Mach numbers from 0.42 to 1.22 at an altitude of 30,000 feet. The performance of the engine over the range investigated could be generalized up to an altitude of 30,000 feet" (p. 1).

"Knock-limited performance data were obtained for three fuels on an R-1830-75 engine in a B-24D airplane at engine speeds of 1800, 2250, and 2600 rpm, a spark advance of 25 degrees B.T.C., and carburetor-air temperatures of 85 F for 1800 and 2250 rpm and 100 F for 2600 rpm. The test fuels were a blend of 80 percent 28-R plus 20 percent triptane (leaded to 4.5 ml TEL/gal), a blend of 80 percent 28-R plus 15 percent toluene (leaded to 4.5 ml TEL / gal), and 28-R fuel. The knock-limited manifold pressure of the toluene blend depreciated more in the lean region than the triptane blend or 28-R fuel" (p. 1).

"Studies have been made by the NACA wing-flow method of the use of fuselage static orifices between the wing and tail of a swept-wing airplane for possible application to service airspeed installations. The tests were made at zero angle of attack. The results indicate that, although the maximum errors are large, these locations are usable from the consideration that the local Mach numbers at the locations studied are sensitive to variation of the true Mach number within the test Mach number range of 0.7 to 1.2" (p. 1).

Report presenting some considerations and techniques pertinent to the application of the supersonic area rule to the design of airplane fuselages. Some of the factors to consider are an extension of the rule to account for the interference effects of the wing and tail on general flow field, the determination of fuselage area developments which result in minimum wave drag, and the influence of wing parameters and Mach number on the effectiveness of fuselage shaping.

From Summary: "In order to determine the conditions of engine operation causing the most severe thermal stresses in the hot parts of a turbojet engine, a J47-25 engine was instrumented with thermocouples and operated to obtain engine material temperatures under steady-state and transient conditions. Temperatures measured during rated take-off conditions of nozzle guide vanes downstream of a single combustor differed on the order of 400 degrees F depending on the relation of the blades position to the highest temperature zone of the burner. Under the same operation conditions, measured midspan temperatures in a nozzle guide vane in the highest temperature zone of a combustor wake ranged from approximately 1670 degrees F at leading and trailing edges to 1340 degrees F at midchord on the convex side of the blade."