An altitude-wind-tunnel investigation of the performance of AN-F-58 and AN-F-32 fuels in an experimental turbojet engine was conducted over a range of simulated altitudes and flight Mach numbers. Combustion efficiencies obtained with AN-F-58 and AN-F-32 fuels were approximately equal. The minimum-speed altitude operational limit was essentially the same with either AN-F-58 or AN-F-32 fuel. Starting characteristics of the two fuels were approximately the same at low wind milling speeds. Visual observation showed no apparent differences in the carbon-deposition rates of AN-F-58 and AN-F-32 fuels.

Report presenting testing of low-aspect-ratio triangular-plan-form lifting surfaces located on conical and cylindrical portions of a body have been determined at Mach number 1.2 and several subsonic speeds to determine if the aerodynamic characteristics of these surfaces at supersonic speeds could be improved by locating them in the subsonic conical-flow field. Results regarding lift and drag coefficients and lift-curve slopes are provided.

High-temperature tensile and thermal-shock investigations were conducted on beryllium oxide and beryllium oxide plus columbium metal additions. X-ray diffraction and metallographic results are given. The tensile strength of 6150 pounds per square inch for beryllium oxide at 1800 degrees F compared favorably with the zirconia bodies previously tested. Additions of 2, 5, 8, 10, 12, and 15 percent by weight of columbium metal failed to improve the shock resistance over that of pure beryllium oxide.

A heat-transfer investigation was conducted with air in an electrically heated platinum tube with long-approach entrance, inside diameter of 0.525 inch, and effective heat-transfer length of 24 inches over ranges of Reynolds number up to 320,000, average inside-tube-wall temperature up to 3053 degrees R, and inlet-air temperature up to 1165 degrees R. Correlation of data by the conventional Nusselt relation resulted in separation of data with tube-wall temperature. Good correlation was obtained, however, by use of a modified Reynolds number.

Report presenting an investigation at supersonic speeds of some of the factors affecting the flow over a rectangular wing with a symmetrical circular-arc section and a 30-percent-chord trailing-edge flap. The main purpose is to obtain more information on which to base the design of supersonic controls. Results regarding the effect of Mach number, effect of wing thickness, effect of fixing transition, effect of sealing the hinge gap, effect of model surface condition and asymmetry, and shock boundary-layer interaction are provided.

Report presenting an investigation in the supersonic tunnel at Mach number 1.85 and angles of attack from 0 to 5 degrees to determine optimum design configurations for a convergent-divergent type of supersonic diffusers with a subsonic diffuser of 5 degrees included divergence angle. Total-pressure recoveries in excess of the theoretical recovery across a normal shock at a free-stream Mach number of 1.85 were obtained with a number of configurations.

Report presenting an investigation to determine the effects of several design changes on the performance of large-capacity, double-entry, centrifugal compressors. Four modifications of a turbojet engine compressor were operated over a range of equivalent impeller tip speeds an the compressor overall and component performances were determined. Results regarding the impeller performance, diffuser performance, and compressor performance are provided.

From Introduction: "The investigation reported herein was therefore undertaken to extend this study to altitude conditions in which the low fuel-flow rates occur over the full range of engine speeds."

Report presenting an investigation of a wing-body combination with a plane triangular wing of aspect ratio 4 and NACA 0005-63 sections in streamwise planes at subsonic and supersonic Mach numbers. Lift, drag, and pitching moment are presented for a range of Mach and Reynolds numbers.

Report discussing an investigation of the rolling effectiveness at transonic and supersonic speeds on a 38.1 degree sweptback tapered wing with NACA 0010-64 airfoil sections and partial-span ailerons of true contour with a modified flt-side blunt trailing-edge shape. The variation of Reynolds number with Mach number and the control effectiveness is provided.

Memorandum presenting the results of a free-jet investigation to determine the internal performance of a 16-inch ram jet. Data were obtained at a range of altitudes and Mach numbers. Results regarding the rake flame holder, effect of fuel injector on burner performance, effect of propylene oxide on burner performance, serrated annular baffle flame holder, diffuser performance, and performance at off-design spike location are provided.

Report presenting testing of a wing-body combination with a plane triangular wing of aspect ratio 2 and NACA 0003-63 sections in streamwise planes at subsonic and supersonic Mach numbers. Lift, drag, and pitching moment are presented for a range of Mach and Reynolds numbers.

"A wing-body combination having a triangular wing of aspect ratio 4 with NACA 0005-63 thickness distribution in streamwise planes, and cambered and twisted for a trapezoidal span distribution has been investigated at both subsonic and supersonic Mach numbers. The lift, drag, and pitching moment of the model are presented for Mach numbers from 0.25 to 0.96 and 1.20 to 1.70 at a Reynolds number of 1.5 million. The variations of the characteristics with Reynolds number are also shown for several Mach numbers" (p. 1).

Report presenting a preliminary analytical evaluation of the air and fuel specific-impulse characteristics of magnesium and magnesium-octene-1 slurries. Adiabatic combustion flame temperature, air specific impulse, and fuel-weight specific impulse are given for each fuel.

From Introduction: "An investigation of the high-speed aerodynamic characteristics of a modified delta wing in combination with a fuselage was conducted in the Langley high-speed 7- by 10-foot tunnel. The model was tested on the sting support system through a Mach number range of 0.40 to 0.90 with both free and fixed transition. Because of the nature of the transition effect, the results seemed to be of the general interest and are presented in the present paper."

"An investigation has been conducted to determine whether three-dimensional flows may be utilized in axial-flow fan and compressor rotors so that the spanwise load distribution may be varied to obtain high pressure rise. Two rotors, one with approximately uniform and one with solid-body downstream tangential-velocity distributions, were designed and tested at the design blade angle" (p. 1).

From Introduction: "This paper presents some recently obtained data on the aerodynamic characteristics of low-aspect-ratio wings at supersonic Mach numbers of 4.04 and 6.9 and discusses some new methods of predicting the lift and drag of such wings. Data on lifting wings in the Mach number range above 2.5 are not plentiful and most of the available data may be found in NACA RM L51D17, NACA RM L51D30, NACA RM L52D15a, NACA RM L52K19, NACA RM L53D03, and NACA RM L53D30a."

"Results are presented of an investigation in the Langley 19-foot pressure tunnel of the longitudinal characteristics of a semispan model wing having 37 degrees sweepback of the leading edge, an aspect ratio of 6, and NACA 641-212 airfoil section perpendicular to the 27-percent-chord line. Several types of stall-control devices including extensible round-nose leading-edge flaps, a leading-edge slat, and a drooped leading edge were investigated; partial- and full-span trailing-edge split and double slotted flaps were also tested. In addition, various combinations of the aforementioned leading- and trailing-edge flaps were investigated" (p. 1).

The gust and draft velocities from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from August 13, 1947 to August 15, 1947 are presented.

This volume continues the NACA study of combustion principles for aircraft propulsion. The various aspects of combustion pertinent to jet engines are organized and interpreted with quite extensive information, particularly for basic or fundamental. subject matter. The report concerns only air-breathing engines and hydrocarbon fuels, and not rocket engines and high-energy fuels.

From Summary: "Two rocket-powered models representative of a fighter-type airplane were investigated in flight at Mach numbers up to 1.01 and 1.07 by the Langley Pilotless Aircraft Research Division at its testing station at Wallops Island, Va. These models incorporated an inverse-taper wing and a vee tail and were flown with controls undeflected and wing and stabilizer set at 0 deg incidence. Values of lateral acceleration, normal acceleration velocity, and drag were obtained by use of telemeters and a Doppler velocimeter radar unit."

An investigation of the performance of several propellers on the YP-47M airplane at high blade loadings has been conducted in the Cleveland altitude wind tunnel at the request of the Air Materiel Command, Army Air Forces. As part of the program, a study was made of a Curtiss 836-14C2-18R1 four-blade propeller. The investigation was made for a range of power coefficients from 0.10 to 1.00 at free-stream Mach numbers of 0.30, 0.40, and 0.50 for density altitudes from 10,000 to 45,000 feet, engine powers from 150 to 2500 brake horsepower, and for engine speeds from 1000 to 2900 rpm.

The gust and draft velocities from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from June 2, 1947 to June 7, 1947, are presented.

Design data are presented for the graphical construction of two-dimensional sharp-edge-throat supersonic nozzles of minimum length for test-section Mach numbers from 1.20 to 10.00. The method of characteristics used in the design is briefly reviewed.