Memorandum presenting an investigation to determine the performance of the J65-B-3 turbojet engine with JP-4 and gaseous-hydrogen fuels. With JP-4 fuel, the maximum altitude for stable combustion was from about 60,000 to 65,000 feet, and the ultimate blowout limit was at an altitude of about 75,000 feet. The steady-state performance with either fuel decreased considerably with increasing altitude.

Report presenting a collection and summary of the wing-aileron rolling-effectiveness data obtained as part of an investigation of lateral control using rocket-powered test vehicles in free flight over a range of Mach numbers. Some effects of trailing-edge angle, aileron-chord ratio, aileron span and location, aspect ratio, wing sweepback, and wing-tail interference are provided.

From Summary: "The dynamic characteristics of an airplane with a proportional-gain roll-control autopilot are discussed. A comparison of three different high-speed fighter airplanes is presented. The dynamic effects of time lags and various gains in the system are described."

Report presenting a theoretical investigation to study the effects of systematic changes in configuration of a representative airframe on the center-of-pressure travel due to changes in angle of attack and in Mach number. The airframe was an unbanked canard missile configuration with low-aspect-ratio coplanar wing and tail surfaces of triangular plan form. Results regarding the center-of-pressure shift due to angle of attack, center-of-pressure shift due to Mach number, and combined effects of angle of attack and Mach number are provided.

Report presenting an investigation to determine the suitability of alloy 73J as a turbojet turbine-blade alloy and the effect of grain size on engine operating life. Blades made of alloy 73J were run in a full-scale J33-9 turbojet engine under cyclic conditions. Results regarding the macroexamination of blades, engine life, engine life against stress-rupture life, blade failures, blade elongation, metallographic results, and blade dimensions and the possible effects of overdimensions are provided.

Report presenting an investigation in the high-speed tunnel at high subsonic speeds and several angles of attack of the chordwise pressure distribution at six spanwise stations on a 45 degree sweptback, untapered vertical tail in sideslip. The presence of the horizontal tail slightly increased the value of section normal-force coefficients on the vertical tail but did not materially alter the nature of the load distribution.

Memorandum presenting the carpet-plotting technique as a more useful and concise method of summarizing the 65-series compressor-blade cascade data. Four different carpet plots are presented. A sample use of the carpet plots is also provided.

Memorandum presenting results of a supersonic flutter investigation of three low-aspect-ratio control surfaces. Two controls were all-movable but the third had a fixed cutout. Results regarding the experiments and calculations are provided.

Report discussing testing of the effects of aeroelasticity on the rolling effectiveness on a model of a McDonnell F-101A airplane wing. The aeroelastic losses varied based on the Mach number and altitude.

Transonic flutter derivatives for unswept wing control surface configurations determined by pressure cell measurements. The control surfaces were mounted on a wing with an aspect ratio of 3, a taper ratio of 0.6, and a wing-thickness ratio of 0.06. Results regarding aerodynamic balance, vortex generators, splitter-plate configurations, and wedges are provided.

Report presenting a brief series of airplane-wing aerodynamic-noise and boundary-layer-profile measurements made in flight as part of an extended investigation of boundary-layer noise. Results regarding the boundary layer data and ratio of root-mean-square sound pressure to the dynamic pressure are provided.

"Investigations have been made in flight and in wind tunnels to determine which components of turbojet installations are most critical in icing conditions, and to evaluate several methods of icing protection. From these studies, the requirements necessary for adequate icing protection and the consequent penalties on engine performance can be estimated. Because investigations have indicated that the compressor-inlet screen constitutes the greatest icing hazard and is difficult to protect, complete removal or retraction of the screen upon encountering an icing condition is recommended" (p. 1).

Memorandum presenting an investigation of an airplane model to determine the effect of area suction trailing-edge flaps and several leading-edge modifications on the aerodynamic characteristics of a 45 degree sweptback wing. The wing had an aspect ratio of 2.8 and a taper ratio of 0.17.

Report presenting an investigation in a 16-inch-diameter simulated afterburner using gaseous hydrogen fuel. Results regarding combustion efficiency, afterburner pressure losses, spontaneous ignition, and a heat-balance check are provided.

Report discussing the ignition-delay determinations of three organophosphorous fuels with nitric acid oxidants at simulated altitude conditions with a small-scale rocket engine.

The present paper summarizes and correlates broadly some of the research results applicable to fin-stabilized ammunition. The discussion and correlation are intended to be comprehensive, rather than detailed, in order to show general trends over the Mach number range up to 7.0. Some discussion of wings, bodies, and wing-body interference is presented, and a list of 179 papers containing further information is included. The present paper is intended to serve more as a bibliography and source of reference material than as a direct source of design information.

Memorandum presenting an investigation of a number of short turbojet combustor configurations for hydrogen fuel in a quarter-annulus duct. The best combustor liner consisted of an annular primary zone and a secondary zone composed of T-shaped channels sloping from the primary zone to the combustor wall.

Memorandum presenting some recently obtained data on the aerodynamic characteristics of low-aspect-ratio wings at supersonic Mach number of 4.04 and 6.9 and discusses some new methods of predicting the lift and drag of such wings. The plan forms, airfoil sections, and thickness ratios of the wings tested are provided.

Memorandum presenting wind-tunnel tests to determine the aerodynamic characteristics of a 15-percent- and a 35-percent-chord plain trailing-edge flap on the NACA 0006 airfoil section. Simultaneous measurements of section lift, drag, and pitching moment were made over a range of Mach numbers, angles of attack, and flap deflections.

Suggested formula are given for determining air-cooled turbine-performance characteristics, such as power and efficiency, as functions of certain parameters. These functions, generally being unknown, are determined from experimental data obtained from specific investigations. Special plotting methods for isolating the effect of each parameter are outlined.

Report presenting an investigation by the transonic-bump method through a range of Mach numbers in the high-speed 7- by 10-foot tunnel to determine the lateral-control characteristics of 30-percent-chord flap-type controls of various spans and locations. The wing of the semispan fuselage-wing combination had 60 degrees of sweepback of the quarter-chord line, a taper ratio of 0.6, an aspect ratio of 4.0, and an NACA 65A006 airfoil section parallel to the free air stream.

The effects of turbine-blade cooling on engine performance were analytically investigated for a turbojet engine in which cooling air is bled from the engine compressor. The analysis was made for a constant turbine-inlet temperature and a range of altitudes to determine the minimum cooling requirements to permit substitution of nonstrategic materials in turbine blading. The results indicate that, for a constant inlet temperature, air cooling of the turbine blades increases the specific fuel consumption and decreases the thrust of the engine. The highest possible cooling effectiveness is desirable to minimize coolant weight flow and its effects on engine performance.

Report presenting the drag of a series of complete airplane-like configurations and their components at transonic velocities using the free-fall method. The configuration tested in this report has a 45 degree sweptback wing of aspect ratio 4.1 mounted forward of the maximum diameter of a 10-inch-diameter body of fineness ratio 12 equipped with stabilizing tail fins. Results are presented as curves showing the variation of drag coefficient with Mach number for the complete configuration and for each component.

Report presenting an investigation using a 4600 pound-thrust turbojet engine as part of a program to determine the comparative performance of fuels conforming to specifications AN-F-58 and AN-F-32. Results regarding the altitude performance, altitude low-speed blow-out limits, idling limits of fuel-metering control, altitude windmilling starts, carbon-deposition rates, and iron oxide contamination are provided.