Preliminary data are enclosed in Tables I, II, II, IV, V, and VI. Tables I to V are data for round nickel tubes in a vertical and inclined (45°) position. Table VI contains some preliminary data for nickel rectangular channels (0.060" and 0.050" spacings) in a vertical position.

"The composition of the solder for the solder plug has been set as the tin-silver eutectic. Final tests on this solder show that life expectancies much longer than 6 months are probable with the current design. The design of the heater tube to contain the solder plug has been settled. This consists of a copper tube impregnated with U235O2. Arrangements have been made to have test specimens fabricated by powder metallurgy techniques. The equipment for the MTR in-pile test of trigger element response times has been largely completed and tested. The design of the complete inner capsule for the BF3 safety element has been developed as well as the cladding technique. Mock-up elements have been tested in the Hanford test reactor to determine the control that may be obtained with elements of this type, although the analysis of the results has not been made. Prototype elements are also ready for testing in the test pile, except for loading with B10F3. Experiments have been designed and submitted for approval for production pile tests of prototype."

"The Atomic energy Commission has undertaken a development program to provide the technology needed for the evaluation and economic design of nuclear power plants. This program is to be carried out during the next five years at several national laboratories and industrial organizations. The Sodium Graphite Reactor (the SGR) is one of those to be investigated and experimentally tested as part of this 5-year effort. The program on the SGR is intended to expand our area of information covering sodium-graphite technology, experimentally demonstrate the feasibility of this reactor complex and extend its performance limits, and apply in information developed to designs suitable for the full-scale nuclear power plant. As a principal part of this program, a Sodium Reactor Experiment (the SRE) is to be constructed and operated; it will be the major experimental facility in which the performance of this reactor will be studied and new technological advances tested. This report continues an earlier series 2-7 in which previous work on the SGR and the SRE has been described. In this report, the progress on the program is described in two main sections. Section A is devoted to work relating to the general technology of Sodium Graphite Reactors, and to …

"An investigation of the chemical effects of 1-Mev electrons on BrF3 at 25 degrees C has been carried out. Pressure measurements taken during the irradiation suggest the presence of Br2 and BrF5 as decomposition products and a fractional distillation of the irradiated liquid confirmed their presence. The extent of decomposition was determined both by fraction distillation and spectrophotometric methods. The radiation effect seemed to reach saturation when approximately 10 per cent of the BrF3 was destroyed. The exposure necessary for the decomposition products to reach a concentration of half the saturated value was calculated to be 2.7 microampere hours/cc BrF3 while the "G" value was found to be 1.5. A qualitative comparison of irradiation dosages from the Statiltron with that expected from spent fuels revealed that little decomposition of BrF3 reagent is to be expected from 1-say cooled Hanford fuel (in pile for 100 days) while in the case of 1-day cooled MTR type fuel (in pile for 12 days) a saturated effect might be realized in 1-3 hours. Since at most only 10 per cent of the BrF3 is destroyed it is concluded that BrF3, from a radiation resistance standpoint, is a suitable standpoint, is a suitable reagent for …

"Engineering pertinent to the development of the sodium-cooled, graphite-moderated type of reactor was continued. This included work on problems related to the zirconium canned moderator, low enrichment uranium fuel, sodium piping, secondary coolant system, shielding, and the control and safety elements. A large fraction of the work was devoted specifically to problems of the proposed Sodium Reactor Experiment (SRE) configuration. In this connection, an integrated effort was initiated to prepare a complete preliminary design of the SRE by an early date. In addition, two alternate sodium-graphite reactor configurations were studied. One was an intermediate size, 145 thermal megawatt, unit optimized for the production of low cost plutonium. The second was a low power 10 thermal megawatt intended for power production, but in which sodium circulation through the core was entirely dependent upon thermal convection."

"Scale-up work on high temperature fuel recovery processes has progressed to the point where the (high temperature) vacuum furnace for several operations to the hot cells has been completed and tested under operating conditions. Small scale experiments on high temperature methods for processing molten irradiated uranium fuel have been made with spent X-10 fuel slug pieces. The results of direct Pu evaporation, treatment with fused fluorides and oxide scavenging were every similar to those found with tracer experiments."

"For a central station reactor power plant of the sodium-graphite type, two designs have been investigated. The first operates as a converter using slightly enriched uranium fuel and produces 150 electrical megawatts. The second operates as a thermal breeder using a U233-Th alloy fuel and produces 300 electrical megawatts. Consideration has also been given to the problem associated with the design and operation of the Sodium Reactor Experiment. All work related to the plutonium plus power sodium-graphite pilot plant, which was undertaken at an earlier date, has been completed."

"Continued progress has been made with the high temperature decontamination processes for irradiated uranium fuel. The fused salt treatment of molten uranium has been extended to UCl3. Plutonium and rare earths were extracted into the UCl3 phase. Direct plutonium distillation from molten irradiated uranium has been scaled up to the hundred gram scale. Solid scavenging experiments using uranium oxide, uranium carbide, and uranium nitride in contact with molten uranium have indicated fission product removal. A scaled-up investigation of the separation and recover of uranium from an SIR type ceramic fuel using the volatile fluoride process has indicated the feasibility of this separation method. The effect of irradiation on the decomposition of BrF3 has been further studies in experiments using the NAA statitron.'

"A study has been made of methods to prepare a fluid containing 1 gram of thorium per milliliter. The methods considered were solutions of thorium salts, suspensions of dry solids in water, and collodial suspensions. Thorium oxide, oxalate, and fluoride were tried in conjunction with one or more surface actants, but it was not possible to attain the required thorium concentration. Thorium hydrosol, produced by peptization of thorium hydroxide and subsequent electrodialysis, gave the necessary concentration of 1 gram per milliliter. A solution of 0.5 gram per milliliter was found to be stable to electron irradiation and did not flocculate upon shaking or standing. Selected surface actans which might be used as protective colloids were found to be unstable to electron irradiation.

This technical report includes (1) World-wide Network (Maps). (2) Fallout of Sr90 at selected sites during June and July. (3) Comparison of Sr90 collection by gummed paper and pot on the roof of the New York Operations Office March through July. (4) Sr90 contamination of cow's milk in Metropolitan New York. (5) Sr90 content of the upper air prior to Castle. (6) Sr90 contamination of pooled fetal bones collected during June from the Metropolitan Area. (7) Sr90 contamination of water supply in the Metropolitan Area June and July.

Concurrently with the production of canned uranium slugs for pile operation there arises the problem of nondestructive testing so that no slug which may fail structurally during operation be placed in the pile. The ultimate goal of any such testing program is to devise nondestructive testing methods which will eliminate defective slugs. A secondary goal of the testing program is to learn as much as possible about the construction of the canned slug so that the mechanisms of failure can be understood. Radiography, an increasingly useful nondestructive test method, offered one possible way of investigating this area.

Progress is reported on (1) direct cycle boiling reactor studies, (2) solvent extraction, (3) fluoride volatilization separation process, (4) elevated temperature separations, (5) fluidization studies, (6) development of analytical techniques, (7) processing and utilization of radioactive wastes.

It was demonstrated by differential thermal analysis (DTA) that: 1. Catastrophic amounts of energy can be stored in diamond. 2. Even at low irradiations, the release takes place over serval hundred degrees, indicating a spectrum of activation energies. 3. At higher irradiations, the stored energy release is considerably less than the increased energy contents and seems not to have been completely released even at the highest temperatures reached. 4. There is some indication of an increased heat capacity below the temperature of stored energy release. It was shown by DTA that large amounts of energy can be stored in silicon carbide on irradiation. The release was found to be spread out over a greater range of temperatures than in diamond and indicated a larger and higher group of activation energies. Catastrophic release was not achieved. The amount of stored energy released over the range of temperatures used was 140 cal/g in a sample irradiated in a water-cooled test hole at HEW for an exposure of 265 Mwd/aT.

Progress is reported on (1) experimental breeder reactor program, (2) solvent extraction, (3) fluoride volatilization separation process, (4) elevated temperature separations, (5) denitration of uranyl nitrate in a fluidized bed, (6) development of analytical techniques, (7) processing and utilization of radioactive wastes.

The index of refraction of PuO2 made by thermal decomposition of PU(C2O2, 6H2O gradually increases from a value < 1.9 to 2.40 as the decomposition temperature is increased from 150 degree to l000 degree C. This change in refractive index parallels a gradual change in the x-ray diffraction pattern from weak, diffuse lines for PuO2 ignited at 150° to sharp, well resolved lines for PuO2 ignited at 1000°C. Similar results are observed for PuO2 made by thermal decomposition of Pu2(C2O4)3*11H2O. The refractive index of PuO2 made from Pu metal at 170°C is 2.40 and is not affected by further ignition at higher temperatures, although crystal growth does occur. The rate of solution of PuO2 in an HCl-KI solution is greatest for samples prepared at low temperatures and decreases markedly for oxides ignited at higher temperatures. These observations hive been interpreted to mean that ignition at higher temperatures causes a gradual perfection of the originally highly distorted and impurity-containing PuO2 lattice obtained by low temperature decomposition of the oxalates and promotes the slow growth of crystallites. Both factors decrease the reactivity of the PuO2.

The index of refraction of PuO2 made by thermal decomposition of PU(C2O2, 6H2O gradually increases from a value < 1.9 to 2.40 as the decomposition temperature is increased from 150 degree to l000 degree C. This change in refractive index parallels a gradual change in the x-ray diffraction pattern from weak, diffuse lines for PuO2 ignited at 150° to sharp, well resolved lines for PuO2 ignited at 1000°C. Similar results are observed for PuO2 made by thermal decomposition of Pu2(C2O4)3*11H2O. The refractive index of PuO2 made from Pu metal at 170°C is 2.40 and is not affected by further ignition at higher temperatures, although crystal growth does occur. The rate of solution of PuO2 in an HCl-KI solution is greatest for samples prepared at low temperatures and decreases markedly for oxides ignited at higher temperatures. These observations hive been interpreted to mean that ignition at higher temperatures causes a gradual perfection of the originally highly distorted and impurity-containing PuO2 lattice obtained by low temperature decomposition of the oxalates and promotes the slow growth of crystallites. Both factors decrease the reactivity of the PuO2.

This technical report summarizes the work which has been done to date on the preparation of magnesium hydride and the attempted preparation of beryllium hydride. Although pure beryllium hydride has not yet been made, the work is continuing, and this report indicates which phases are thought to be worth further work.

Experimental data pertinent to the evaluation of hazards involved in the exposure of personnel to tritium and tritium oxide are reviewed. Conclusions are drawn and recommendations made with regard to the control of these hazards.

The prompt administration of zirconium citrate was at least twice as effective as the prompt administration of calcium disodium salt of ethylenediaminetetraacetic acid (CaEDTA) in preventing deposition of plutonium in the skeleton. On the other hand, CaEDTA was twice as effective as zirconium citrate in preventing the deposition of plutonium in soft tissues. The combined administration of zirconium citrate and CaEDTA was the most effective treatment for preventing the deposition of plutonium in the total rat. Zirconium malate offered no advantage over zirconium citrate, and appeared to be somewhat more toxic. Three doses of the zirconium salts over a four-day period were no more effective than a single dose.

The feasibility of using Teflon bellows as the pulsing device for solvent extraction pulse columns has been previously demonstrated by life test of various sizes of Teflon bellows. This report describes a compact Teflon bellows pulse generator and drive assembly which was designed, built, and tested by the Chemical Development Unit. The pulse generator assembly is suitable for a number of applications where pulse generators are required to pulse solvent extraction columns.

Abstract: "Thirty-four uranium ingots containing controlled amounts of carbon, nitrogen, and Mgl2 slag were cast, rolled, and examined to investigate the relation between these impurities and the quality of the rolled rod. Carbon in concentrations up to 1400 ppm and nitrogen up to 170 ppm, either singly or in combination, had no significant effect on the number of defects observed in the rolled rod. The quality of the rods, however decreased with increasing amount of slag necessary to cause observable differences in the rod could not be detected on analysis, but was visible in the microstructure."

Abstract: "Probes were used to measure certain properties of the cloud of positive ions and electrons ejected from a pulsed ion source having two hydrogen-loaded electrodes. Time-of-flight measurements show: the presence of H+ ions with 50 ev directed energy; an increase of this energy with increasing pulse current in the source; a higher peak yield of ions with higher peak currents in the source; and higher yields and higher ion energies up to 110 ev have been recorded with the use of a pulsed magnetic field impressed upon the source. The neutral positive ion-electron beam from the source has been projected against an increasing magnetic field and the reflected and transmitted signals have been recorded and compared as a function of the magnetic field. Probe signals from the plasma as it encounters the magnetic field are oscillatory, suggesting that magnetohydrodynamic phenomena are presented."

Abstract: "Observations of refracted sound waves from atomic tests at the Nevada and Pacific Proving Grounds are evaluated to show temperature and winds in the ozonosphere. A simplified method of making these interpretations is presented to reduce the computation work load normally associated with atmospheric sound studies."

Abstract: "In experimental studies, decontamination factors of 1000 to 3000 were obtained by electrostripping deposited radioactivity from stainless steel surfaces, used as the anode, in 2% sulfuric acid at current densities as low as 0.01 amp/in.-2. Stainless steel cathodes were used. The method was successfully applied to contaminated equipment."