This report provides a usable reference of methods and procedures for the construction of both one-sided and two-sided ..gamma../P statistical tolerance limits for design application to both linear and nonlinear models in any number of variables.

The development program to identify the critical parameters for the process of converting thorium nitrate solution into thoria powder is described. Thorium oxalate hexahydrate is precipitated from the reaction of thorium nitrate solution with oxalic acid. The resulting thorium oxalate hexahydrate slurry is filter pressed into a cake which is air calcined to form thoria powder. Changes in the critical processing parameters such as free nitric acid content of the thorium nitrate solution, precipitation temperature, and calcining temperature altered the thoria powder characteristics, and thus its capability for being fabricated into fuel pellets. The objective of the powder preparation effort was to obtain thoria powders which could be formed by conventional ceramic fabrication techniques into thoria and thoria-urania pellets of high density and high integrity having a nearly uniform large grain structure.

Wear of the Zircaloy cladding of LWBR irradiation test fuel rods, resulting from relative motion between rod and rod support contacts, is reported. Measured wear depths were small, 0.0 to 2.7 mils, but are important in fuel element behavior assessment because of the local loss of cladding thickness, as well as the effect on grid spring forces that laterally restrain the rods. An empirical wear analysis model, based on out-of-pile tests, is presented. The model was used to calculate the wear on the irradiation test fuel rods attributed to a combination of up-and-down motions resulting from power and pressure/temperature cycling of the test reactor, flow-induced vibrations, and assembly handling scratches. The calculated depths are generally deeper than the measured depths.

A model has been devised for incorporating into the thermal feedback procedure of the PDQ few-group diffusion theory computer program the explicit calculation of depletion and temperature dependent fuel-rod shrinkage and swelling at each mesh point. The model determines the effect on reactivity of the change in hydrogen concentration caused by the variation in coolant channel area as the rods contract and expand. The calculation of fuel temperature, and hence of Doppler-broadened cross sections, is improved by correcting the heat transfer coefficient of the fuel-clad gap for the effects of clad creep, fuel densification and swelling, and release of fission-product gases into the gap. An approximate calculation of clad stress is also included in the model.

This report describes the use of a delayed neutron pellet assay gage to determine nondestructively the fissile content of fuel pellets during the manufacture of the Light Water Breeder Reactor (LWBR) core. The gage characteristics are described including the nature of the calibration curves and the gage sensitivities to pellet parameters. Statistical methods are derived for analyzing the data to obtain the mean weight percent of total uranium in each blend of fuel material as well as the loading precision of each fuel rod. The fissile loading of each fuel rod was determined to better than 0.25% at the 2 sigma level, and the fissile content of eight fuel compositions in the LWBR core was obtained to better than 0.1%. Use of this gage and the data analysis methods described in this report reduced the need for destructive chemical analysis of fuel pellets by a factor of two.

Seamless Zircaloy-4 tubing is utilized as fuel rod cladding in light water reactors. Water corrosion tests at 68OF have been performed to determine the corrosion and hydriding characteristics of Zircaloy-4 tubing, fabricated by cold reduction and finished in two metallurgical conditions: a stress-relief anneal (SRA) and a recrystallization anneal (RXA). These corrosion tests revealed differences in the post-transition corrosion product weight gains of the two materials. A computer corrosion model, designated CHORT, was developed from the test data and ascribes the observed difference in material weight gain to an assumed difference in the periodicity of a postulated cyclic buckling of the oxide.

ASBLT is a computer program consisting of DATATRAN MODULES which was used during the manufacturing phase of LWBR to collect and evaluate as-built data. The program was part of the LWBR fuel rod inspection process and produced sections of module assembly certification reports. ASBLT used fuel pellet, fuel rod and module assembly data to compute core inventories and to supply input to nuclear design programs for as-built core calculations.

Six different fastened joints representing the various combinations of materials in contact with Zircaloy in the Light Water Breeder Reactor (LWBR) were tested in 520/sup 0/F water for 60 days to determine the out-of-pile hydriding tendencies of the Zircaloy components in the joints. No evidence of massive, accelerated hydriding was found in this test although other testing has shown that local hydriding can occur in one of the fasteners. The same six fastener designs were tested in 600/sup 0/F water for 60 days to assess their load retention capability (thermal relaxation). The measured relaxation of these fasteners confirmed the predicted values for the conditions of the test.

This report presents and discusses the results of physics tests performed at beginning of life on the Light Water Breeder Reactor (LWBR). These tests have confirmed that movable seed assembly critical positions and reactivity worths, temperature coefficients, xenon transient characteristics, core symmetry, and core shutdown are within the range of values used in the design of the LWBR and its reactor protection analysis. Measured core physics parameters were found to be in good agreement with the calculated values.

An experiment has been performed to determine the effect of motion of a thermal shield on the neutron signal expected from ex-core detectors. Using a mockup of the LWBR reactor vessel, thermal shield, and core barrel in conjunction with a /sup 252/Cf neutron source, the change in detector signal with displacement of the various components was investigated. It was found that moving the thermal shield would produce a significant change in detector signal, although the effect was smaller than would be produced by moving the source and core barrel together. The results were substantiated by two-dimensional discrete-ordinate calculations.

This report describes the operation of the Shippingport Atomic Power Station during the LWBR (Light Water Breeder Reactor) Core lifetime. It also summarizes the plant-oriented operations during the period preceding LWBR startup, which include the defueling of The Pressurized Water Reactor Core 2 (PWR-2) and the installation of the LWBR Core, and the operations associated with the defueling of LWBR. The intent of this report is to examine LWBR experience in retrospect and present pertinent and significant aspects of LWBR operations that relate primarily to the nuclear portion of the Station. The nonnuclear portion of the Station is discussed only as it relates to overall plant operation or to unusual problems which result from the use of conventional equipment in radioactive environments. 30 refs., 69 figs., 27 tabs.

FLASH6 computer program calculations are compared with experimental data from two simulated loss-of-coolant accident blowdown tests which are designated as numbers 2 and 3 in the Standard problem Series sponsored by the Nuclear Regulatory Commission for reactor safety assessment. Both tests are isothermal blowdowns smulating a double-ended, cold-leg break and were conducted in the electrically-heated, 1-1/2 Loop Semiscale System at Idaho National Engineering Laboratory. The blowdown tests were initiated at nominal conditions of 575/sup 0/F, 2250 psia and 17.3 lbm/sec loop flow rate.

Measurements of fission product iodine and cesium are reported for thoria and binary (ThO/sub 2/--UO/sub 2/) fuels with various irradiation histories. These volatile fission products were measured on the cladding surface or in the fuel by using specially developed radiochemical techniques. The radiochemical iodine measurements are found to be in general agreement with a theoretical iodine release model for irradiated fuel. Microprobe examinations of irradiated fuel rod cladding sections show fission product cesium to be located preferentially at the pellet to pellet interface region. Fission product iodine was detected in the interface region of one sample but generally remained below the microprobe limit of detection. 18 figures, 7 tables.

Although not a problem in recent commercial power reactors, including the Shippingport Light Water Breeder Reactor, internal hydriding of Zircaloy cladding was a persistent cause of gross cladding failures during the 1960s. It occurred in the fuel rods of water-cooled nuclear power reactors that had a small cladding defect. This report summarizes the experimental findings, causes, mechanisms, and methods of minimizing internal hydriding in defected Zircaloy-clad fuel rods. Irradiation test data on the different types of defected fuel rods, intentionally fabricated defected and in-pile operationally defected rods, are compared. Significant factors affecting internal hydriding in defected Zircaloy-clad fuel rods (defect hole size, internal and external sources of hydrogen, Zircaloy cladding surface properties, nickel alloy contamination of Zircaloy, the effect of heat flux and fluence) are discussed. Pertinent in-pile and out-of-pile test results from Bettis and other laboratories are used as a data base in constructing a qualitative model which explains hydrogen generation and distribution in Zircaloy cladding of defected water-cooled reactor fuel rods. Techniques for minimizing internal hydride failures in Zircaloy-clad fuel rods are evaluated.

This report summarizes the refueling operations performed to install a Light Water Breeder Reactor (LWBR) core into the existing pressurized water reactor vessel at the Shippingport Atomic Power Station. Detailed descriptions of the major installation operations (e.g., primary system preconditioning, fuel installation, pressure boundary seal welding) are included as appendices to this report; these operations are of technical interest to any reactor servicing operation, whether the reactor is a breeder or a conventional light water non-breeder core.

Destructive examination of 12 representative Light Water Breeder Reactor fuel rods was performed following successful operation in the Shippingport Atomic Power Station for 29,047 effective full power hours, about five years. Light Water Breeder Reactor fuel rods were unique in that the thorium oxide and uranium-233 oxide fuel was contained within Zircaloy-4 cladding. Destructive examinations included analysis of released fission gas; chemical analysis of the fuel to determine depletion, iodine, and cesium levels; chemical analysis of the cladding to determine hydrogen, iodine, and cesium levels; metallographic examination of the cladding, fuel, and other rod components to determine microstructural features and cladding corrosion features; and tensile testing of the irradiated cladding to determine mechanical strength. The examinations confirmed that Light Water Breeder Reactor fuel rod performance was excellent. No evidence of fuel rod failure was observed, and the fuel operating temperature was low (below 2580/sup 0/F at which an increased percentage of fission gas is released). 21 refs., 80 figs., 20 tabs.

The PDQ-8 program is designed to solve the neutron diffusion, depletion problem in one, two, or three dimensions on the CDC-6600 and CDC-7600 computers. The three dimensional spatial calculation may be either explicit or discontinuous trial function synthesis. Up to five lethargy groups are permitted. The fast group treatment may be simplified P(3), and the thermal neutrons may be represented by a single group or a pair of overlapping groups. Adjoint, fixed source, one iteration, additive fixed source, eigenvalue, and boundary value calculations may be performed. The HARMONY system is used for cross section variation and generalized depletion chain solutions. The depletion is a combination gross block depletion for all nuclides as well as a fine block depletion for a specified subset of the nuclides. The geometries available include rectangular, cylindrical, spherical, hexagonal, and a very general quadrilateral geometry with diagonal interfaces. All geometries allow variable mesh in all dimensions. Various control searches as well as temperature and xenon feedbacks are provided. The synthesis spatial solution time is dependent on the number of trial functions used and the number of gross blocks. The PDQ-8 program is used at Bettis on a production basis for solving diffusion--depletion problems. The report describes …

Critical heat flux experiments were conducted for upflow of water in a vertical 84 inch annular flow channel, 0.303 inch heated I.D. and 0.500 inch unheated O.D. Test data were obtained at pressures from 1200 to 2000 psia, mass velocities from 0.25 x 10/sup 6/ to 2.8 x 10/sup 6/ lb/hr-ft/sup 2/ and inlet temperatures ranging from 200 to 600/sup 0/F. Three different test sections were employed with (1) axially uniform heat flux over the 84 inch length to serve as a no-hot-patch data base, (2) axially uniform heat flux over 82 inches with a 1.5 heat flux ratio hot patch over the last two inches, and (3) axially uniform heat flux over 82 inches with a 2.25 heat flux ratio hot patch over the last two inches.

The principal hydraulic performance features of the Light Water Breeder Reactor are summarized in this report. The calculational models and procedures used for prediction of reactor flow and pressure distributions under steady-state and transient operating conditions are described. Likewise, the analysis models for evaluation of the static and dynamic performance characteristics of the hydraulically-balanced and hydraulically-buffered movable-fuel reactivity-control system are outlined. An extensive test program was conducted for qualification of the subject LWBR hydraulic evaluation models. The projected LWBR hydraulic performance is shown to fulfill design objectives and functional requirements.

Fission gas release data are presented from 51 fuel rods irradiated as part of the LWBR irradiations test program. The fuel rods were Zircaloy-4 clad and contained ThO/sub 2/ or ThO/sub 2/-UO/sub 2/ fuel pellets, with UO/sub 2/ compositions ranging from 2.0 to 24.7 weight percent and fuel densities ranging from 77.8 to 98.7 percent of theoretical. Rod diameters ranged from 0.25 to 0.71 inches and fuel active lengths ranged from 3 to 84 inches. Peak linear power outputs ranged from 2 to 22 kw/ft for peak fuel burnups up to 56,000 MWD/MTM. Measured fission gas release was quite low, ranging from 0.1 to 5.2 percent. Fission gas release was higher at higher temperature and burnup and was lower at higher initial fuel density. No sensitivity to UO/sub 2/ composition was evidenced.

The purpose of the Department of Energy Water Cooled Breeder Program was to demonstrate pratical breeding in a uranium-233/thorium fueled core while producing electrical energy in a commercial water reactor generating station. A demonstration Light Water Breeder Reactor (LWBR) was successfully operated for more than 29,000 effective full power hours in the Shippingport Atomic Power Station. The reactor operated with an availability factor of 76% and had a gross electrical output of 2,128,943,470 kilowatt hours. Following operation, the expended core was examined and no evidence of any fuel element defects was found. Nondestructive assay of 524 fuel rods determined that 1.39 percent more fissile fuel was present at the end of core life than at the beginning, proving that breeding had occurred. This demonstrates the existence of a vast source of electrical energy using plentiful domestic thorium potentially capable of supplying the entire national need for many centuries. To build on the successful design and operation of the Shippingport Breeder Core and to provide the technology to implement this concept, several reactor designs of large breeders and prebreeders were developed for commercial-sized plants of 900--1000 Mw(e) net. This report summarizes the Water Cooled Breeder Program from its inception in 1965 …

Data from top injection ECCS tests conducted at Columbia University have been analyzed as part of an effort to qualify the FLASH-6 computer program for performing post-blowdown heat transfer calculations for the LWBR Safety Analysis. These experiments, which employed a full-scale fuel assembly with electrical heater rods to simulate an inlet rupture for a pressurized water reactor, provided test conditions and rod cooling mechanisms quite similar to those encountered in the postulated LWBR cold leg break loss-of-coolant accident. Clad temperature predictions were obtained using both the modified Dittus-Boelter and the Dougall-Rohsenow correlations to evaluate beyond CHF heat transfer coefficients. Overall comparisons using the FLASH calculated flow rates indicated that the rod temperature calculations were conservative using either of the heat transfer correlations because virtually none of the coolant was calculated to penetrate the heated test assembly. Heat transfer model comparisons were also performed by adjusting the calculation so that coolant was injected directly into the top of the rod bundle to simulate the experimentally observed flow conditions. Once this downflow was forced, conservative temperature predictions were obtained using the Dougall-Rohsenow correlation, whereas the modified Dittus-Boelter beyond CHF option yielded non-conservative results.

A model was developed to estimate the radiation dose commitments received by people in the vicinity of a facility that releases radionuclides into the atmosphere. This model considers dose commitments resulting from immersion in the plume, ingestion of contaminated food, inhalation of gaseous and suspended radioactivity, and exposure to ground deposits. The dose commitments from each of these pathways is explicitly considered for each radionuclide released into the atmosphere and for each daughter of each released nuclide. Using the release rate of only the parent radionuclide, the air and ground concentrations of each daughter are calculated for each position of interest. This is considered to be a significant improvement over other models in which the concentrations of daughter radionuclides must be approximated by separate releases.

The shape of the thorium absorption cross section near thermal energies was investigated. This shape is dominated by one or more negative energy resonances whose parameters are not directly known, but must be inferred from higher energy data. Since the integral quantity most conveniently describing the thermal cross section shape is the Westcottg-factor, effort was directed toward establishing this quantity to high precision. Three nearly independent g-factor estimates were obtained from measurements on a variety of foils in three different neutron spectra provided by polyethylene-moderated neutrons from a /sup 252/Cf source and from irradiations in the National Bureau of Standards ''Standard Thermal Neutron Density.'' The weighted average of the three measurements was 0.993 +- 0.004. This is in good agreement with two recent evaluations and supports the adequacy of the current cross section descriptions.