The Acceptance Test Procedure for the 241-AN-107 Caustic Addition Mixer Pump Data logger, WHC-SD-WM-ATP-149, was started on September 25, 1995, and completed November 13, 1995. K.G. Carothers of Tank Waste Remediation Engineering requested the test procedure and ICF Kaiser Control Systems Engineering group wrote the test procedure and executed it at the 305 building in 300 area and at the 241-AN Tank Farm in 200 East area. The purpose of this report is to document that the Caustic addition Mixer Pump Data logger, functioned as intended as installed at 241-AN-107 tank farm.

The degradation of fracture toughness, tensile, and Charpy-impact properties of Type 308 stainless steel (SS) pipe welds due to thermal aging has been characterized at room temperature and 290 C. Thermal aging of SS welds results in moderate decreases in Charpy-impact strength and fracture toughness. For the various welds in this study, upper-shelf energy decreased by 50-80 J/cm{sup 2}. The decrease in fracture toughness J-R curve or JIC is relatively small. Thermal aging had little or no effect on the tensile strength of the welds. Fracture properties of SS welds are controlled by the distribution and morphology of second-phase particles. Failure occurs by the formation and growth of microvoids near hard inclusions; such processes are relatively insensitive to thermal aging. The ferrite phase has little or no effect on the fracture properties of the welds. Differences in fracture resistance of the welds arise from differences in the density and size of inclusions. Mechanical-property data from the present study are consistent with results from other investigations. The existing data have been used to establish minimum expected fracture properties for SS welds.

Development of the computer models for slurry carbonization have begun and were based upon the collected data (mass balances, yield, temperatures, and pressures) from the previous pilot plant campaigns. All computer models are being developed with Aspen`s SpeedUp{trademark} software. The primary flow sheet with major alternatives has been developed and the majority of equipment descriptions and models, cost algorithms, and baseline parameters have been input to SpeedUp. The remaining modeling parameters will be input in the next reporting period and the initial flow sheet skeleton and model will be completed. The computer models will focus on optimizing capital and operating costs, and evaluating alternative waste water recycling technologies. The weaknesses of the previous pilot plant data and the data required for design of the commercial demonstration facility were identified. The identified weaknesses of the existing data included mass balance precision and accuracy, reactor residence time control (i.e. reactor level control), reactor temperature variations, and air entrainment in the feed RDF slurry. To improve mass balance precision and accuracy, an alternative carbonization gas flow meter will be designed and installed on the pilot plant. EnerTech`s carbonization gas flow meter design has been submitted to the EERC for final approval. In addition, …

A Preliminary Low-Level Waste Feed Staging Plan was prepared. The plan supports the Phase I privatization effort by providing recommendations that may influence the technical content of the final request for proposal, and the interface control documents for the turnover of two double-shell tanks (DST) to the private contractors for use as feed tanks and the transfer of supernate to these tanks. Additionally, the preliminary schedule of feed staging activities will be useful to both RL and the private bidders during the contract negotiation period. A revised feed staging plan will be issued in August 1996 reflecting anticipated changes in the request for proposal, resolution of issues identified in this report, and completion of additional work scope.

None

None

None

INTEG is a computer program to calculate groundwater contamination concentration levels and human dose from inventories, vadose zone transport, and aquifer transport.

The Arctic National Wildlife Refuge (ANWR) is an area rich in fauna, flora, and oil potential, where development has been debated for over 36 years. Current law forbids oil and gas leasing. This report discusses debate over whether or not to open the ANWR up for development and includes discussion of various legislative options under consideration.

Declining fish populations threaten an important food source. Natural catastrophes, pollution, habitat destruction, and overfishing contribute to the depletion of fish stocks. Overexploitation of fishery resources often occurs when management allows expanding and increasingly efficient fishing fleets to continue harvesting dwindling supplies. Although prevalent, overexploitation is not universal and its extent varies among areas, species, and fisheries. This report discusses the issue of overfishing and its possible consequences, as well as domestic and international efforts to combat overfishing.

Over the past decade, numerous major treaties have been concluded to deal with global environmental concerns. This report very briefly summarizes major global environmental treaties currently in effect, selected to include those that are subjects of frequent interest by Members of Congress.

The Mixed Waste Focus Area (MWFA) has chartered the Savannah River Technology Center (SRTC) to design and fabricate a Transportable Vitrification System (TVS) to demonstrate treatment of Low-Level Mixed Waste (LLMW). This system will be used to demonstrate the feasibility of vitrification on several LLMW streams. The first stream to be demonstrated will be the Oak Ridge Reservation (ORR) K-25 B&C Pond sludge. Before the demonstrations in the TVS can take place, a surrogate sludge vitrification demonstration had to be performed in the EV-16 melter located at the DOE Industrial Center for Vitrification Research (Center) at the Environmental Systems Engineering Department at Clemson University. During the demonstration at the Center, a 50 wt% B&C sludge glass composition was tested to determine any processing problems. A total of 1510 pounds (686 kg) of glass were produced from 9328 pounds (4240 kg) of surrogate feed. The resulting glass product was homogeneous and very durable.

DWPF-Engineering requested that SRTC determine the minimum indicated melter vapor space temperature that must be maintained in order to minimize the potential for off-gas flammability during a steady sludge-only feeding operation at 1.0 GPM containing 14,000 ppm total organic carbon. The detailed scope of this request is described in the technical task request, HLW-DWPF-TTR-960092 (DWPT Activity No. DWPT-96-0065). In response to this request, a dynamic simulation study was conducted in which the concentration of flammable gases was tracked throughout the course of a simulated 3X off-gas surge using the melter off-gas (MOG) dynamics model. The results of simulation showed that as long as the melter vapor space temperature as indicated on TI4085D is kept at 570 degrees C or higher, the peak concentration of combustible gases in the melter off-gas system is not likely to exceed 60 percent of the lower flammability limit (LFL). The minimum TI4085D of 570 degrees C is valid only when the air purges to FIC3221A and FIC3221B are maintained at or above 850 and 250 lb/hr, respectively. All the key bases and assumptions along with the input data used in the simulation are described in the attached E-7 calculation note.

With many nuclear reactors and facilities being decommissioned in the next ten to twenty years the concern for handling and storing Radioactive Scrap Metal (RSM) is growing. Upon direction of the DOE Office of Environmental Restoration and Waste Management, Lockheed Idaho Technology Company (LITCO) is developing technologies for the conditioning of spent fuels and high-level wastes for interim storage and repository acceptance, including the recycling of Radioactive Scrap Metals (RSM) for beneficial reuse with the DOE complex. In February 1993, Montana Tech of the University of Montana was contracted to develop and demonstrate technologies for the decontamination of stainless steel RSM. The general objectives of the Montana Tech research program included conducting a literature survey, performing laboratory scale melt refining experiments to optimize decontaminating slag compositions, performing an analysis of preferred melting techniques, coordinating pilot scale and commercial scale demonstrations, and producing sufficient quantities of surrogate-containing material for all of the laboratory, pilot and commercial scale test programs. Later on, the program was expanded to include decontamination of carbon steel RSM. Each research program has been completed, and results are presented in this report.

This document provides the preliminary planning basis for the U.S. Department of Energy (DOE) to provide a sufficient quantity of high-level waste feed to the privatization contractor during Phase I. By this analysis of candidate high-level waste feed sources, the initial quantity of high-level waste feed totals more than twice the minimum feed requirements. The flexibility of the current infrastructure within tank farms provides a variety of methods to transfer the feed to the privatization contractor`s site location. The amount and type of pretreatment (sludge washing) necessary for the Phase I processing can be tailored to support the demonstration goals without having a significant impact on glass volume (i.e., either inhibited water or caustic leaching can be used).

The goal of the proposed research is to test a statistical model of speech recognition that incorporates the knowledge that speech is produced by relatively slow motions of the tongue, lips, and other speech articulators. This model is called Maximum Likelihood Continuity Mapping (Malcom). Many speech researchers believe that by using constraints imposed by articulator motions, we can improve or replace the current hidden Markov model based speech recognition algorithms. Unfortunately, previous efforts to incorporate information about articulation into speech recognition algorithms have suffered because (1) slight inaccuracies in our knowledge or the formulation of our knowledge about articulation may decrease recognition performance, (2) small changes in the assumptions underlying models of speech production can lead to large changes in the speech derived from the models, and (3) collecting measurements of human articulator positions in sufficient quantity for training a speech recognition algorithm is still impractical. The most interesting (and in fact, unique) quality of Malcom is that, even though Malcom makes use of a mapping between acoustics and articulation, Malcom can be trained to recognize speech using only acoustic data. By learning the mapping between acoustics and articulation using only acoustic data, Malcom avoids the difficulties involved in collecting …

This project was canceled shortly after final approval. Thus, there are no accomplishments. The major problem encountered was the extreme effort required to obtain approval (about two years) to start work. No lessons were learned. No close-outs items require addressing. No contracts were let. Only two commitments were scheduled to be completed before the Y-12 cancellation: both involved the industrial partners: (1) the industrial partners were to define the preferred sensor power requirements, this was completed and the details are treated as proprietary or CRADA-Protected Information; (2) the industrial partners were to perform a physical integration assessment of sensor technologies and the details are treated as proprietary or CRADA-Protected Information.

A series of experiments in which the stirrer speed was varied during a methanol synthesis run with BASF S3-86 catalyst showed that mass transfer limitations were present at 750 psig reactor pressure and at space velocities of 5000 and 10000 sl/kg(cat.)-hr.. There was no effect of stirrer speed on reaction rate at 2500 psig reactor pressure and 16500 sl/kg(cat.)-hr. space velocity. However, this was probably due to a close approach to equilibrium rather than to the lack of a mass transfer effect. The most plausible explanation for the presence of a mass transfer influence is the position of the gas feed dip tube relative to the agitator impeller. A second set of stirrer speed experiments using the same catalyst showed that feeding into the reactor headspace produced much lower reaction rates, compared with gas feed through a dip tube. The headspace feed also showed a strong dependence on stirrer speed, consistent with the dip tube feed results. In a ``blank` run at 375{degree}C with decahydronaphthalene, about 110 mL of the initial charge of 150 mL remained in the reactor after 73 hours of operation at 375{degree}C and 850 psig of hydrogen. The rate of hydrocarbon evolution was low throughout the …

A sol-gel granulation method was developed to prepare spherical {gamma}-alumina granular supports and supported CuO granular sorbents for flue gas desulfurization. The prepared {gamma}-alumina supported CuO sorbents exhibit desirable pore structure and excellent mechanical properties. The sorbents contain higher loading (30-40 wt. %) of CuO dispersed in the monolayer or sub-monolayer form, giving rise to a larger SO{sub 2} sorption capacity ({gt}20 wt.%) and a faster sorption rate as compared to similar sorbents reported in the literature. With these excellent sulfation and mechanical properties, the sol-gel derived {gamma}-alumina supported CuO granular sorbents offer great potential for use in the dry, regenerative flue gas desulfurization process. Research efforts were also made to prepare DAY zeolite supported sorbents with various CuO contents by the microwave and conventional thermal dispersion methods at different conditions. Monolayer or sub-monolayer coating of Cu(NO{sub 3})sub 2 or CuO was achieved on several DAY supported sorbents by the microwave heating method but not by the conventional thermal dispersion method. The DAY zeolite supported CuO sorbents prepared by the microwave heating method can adsorb up to 15 wt.% of SO{sub 2}. The results obtained have demonstrated the feasibility of effective preparation of zeolite supported CuO sorbents by the microwave …

This document outlines the steps required to properly document the operability testing of this prototypical system. The tree is deployed in the annulus of the underground nuclear waste storage tank 241-AN-107; it is to monitor the temperature gradient of the primary containment wall using 3 arrays of contact thermocouples.

This document describes the conceptual design for the Sludge Receipt Subproject that meets the functional design criteria. Also included in this document are the cost estimate and schedule.

Standard thermal stability tests were carried out on four liquids: decahydroquinoline (DHQ); 1, 3-Di-4 piperidylpropane (134PPDP), Naphthenic Base 37 and tetrahydronaphthalene (tetralin). Tetralin was more stable than decahydronaphthalene (Decalin{reg_sign}), and THQ was slightly less stable. Both tetralin and THQ should be evaluated further as slurry liquids in the presence of catalyst and syngas. Naphthenic Base 37 and 134PPDP do not have satisfactory thermal stability. Vapor pressure osmometry (VPO) was shown to be an unreliable technique for measuring the average molecular weight of slurry liquids. Gas chromatography/mass spectroscopy (GUMS) is a more accurate technique for pure compounds.

The overall objective to this two phase program is to investigate dry carbon-based sorbents for mercury control. During Phase I, a bench-scale field test device that can simulate an electrostatic precipitator, a pulse-jet baghouse, or a reverse-gas baghouse will be designed and integrated with an existing pilot-scale facility at Public Service Company of Colorado`s (PSCo`s) Comanche station. Various sorbents will then be injected to determine the mercury removal efficiency for each. During Phase II effort, component integration of the most promising technologies shall be tested at the 5000 acfm pilot-scale. The primary task currently underway is the facility design. The design is expected to be finished in January, 1996. The facility, regardless of the particulate control module configuration, will be fitted with supply line injection port, through which mercury sorbents and SO{sub 2} control sorbents can be added to the flue gas stream.

Enriched stable isotopes are required for production of radionuclides as well as for research and diagnostic uses. Science Research Laboratory (SRL) has developed a plasma centrifuge for moderate throughput of enriched stable isotopes, such as {sup 13}C, {sup 17}O, {sup 18}O, and {sup 203}Tl, for medical as well as other applications. Dwindling isotope stocks have restricted the use of enriched isotopes and their associated labeled organic molecules in medical imaging to very few research facilities because of high costs of isotope separation. With the introduction of the plasma centrifuge separator, the cost per separated gram of even rarely occurring isotopes ({le} 1% natural abundance) is potentially many times lower than with other separation technologies (cryogenic distillation and calutrons). The centrifuge is a simple, robust, pulsed electrical discharge device that has successfully demonstrated isotope separation of small (mg) quantities of {sup 26}Mg. Based on the results of the Phase 2 program, modest enhancements to the power supplies and cooling systems, a centrifuge separator will have high repetition rate (60 pps) and high duty cycle (60%) to produce in one month kilogram quantities of highly enriched stable isotopes. The centrifuge may be used in stand-alone operation or could be used as a …