Report presenting a description of a device for indicating stream Mach number in a high-speed tunnel. It consists of a mechanism for determining the pressure ratio that Mach number is a function of. The instrument is in service in the 8-foot high-speed tunnel and its accuracy has been found adequate for wind-tunnel requirements.

Report presenting an analysis of data for turbulent boundary layers along wings and bodies of various shapes in order to determine the fundamental variables that control the development of turbulent boundary layers. Results indicate that the type of velocity distribution in the boundary layer could be expressed in terms of a single parameter.

"The effect of two-dimensional bumps and surface waviness on the pressure distribution over airfoils is considered. It is shown that the results of the analysis may be useful in evaluating the effects of accidental or intended surface distortions on the drag and critical Mach number of airfoils" (p. 1).

Report presenting force-test measurements in two-dimensional flow made in the 4- by 6-foot vertical tunnel to determine the aerodynamic characteristics of an NACA 66(215)-014 airfoil equipped with true-contour, straight-contour, and beveled-trailing-edge flaps with chords 30 percent of the airfoil chord. The results are presented in the form of aerodynamic section characteristics for several flap deflections and for a sealed and unsealed gap at the flap nose.

Report presenting hinge-moment, lift, pressure difference across the balance, and pressure-distribution measurements in the two-dimensional test section of the stability tunnel on a 0.60 aileron-chord sealed internal-balance aileron on a specified NACA airfoil. The primary test objective was to determine the effect of speed on the action of the aileron.

Report presenting hinge moment, lift, and pressure-distribution measurements made on a Frise aileron on an NACA 23012 airfoil in the two-dimensional test section of the stability tunnel. Speeds up to 360 miles per hour corresponding to a Mach number of about 0.470 were used.

Report presenting tests made on an NACA 23012 airfoil fitted with a 20-percent-chord, true-contour aileron with 35-percent-chord, extreme blunt-nose balance. The primary purpose of the investigation was to determine the variation of the aerodynamic characteristics of this type of aileron with airspeed; the effect of variations of gap width and balance-nose radii was also investigated. Results regarding hinge moments, lift, and pitching-moment coefficients are provided.

"Hinge-moment, lift, and pressure-distribution measurements were made in the two-dimensional test section of the NACA stability tunnel on a blunt-nose balance-type aileron on an NACA 66,2-216 airfoil at speeds up to 360 miles per hour corresponding to a Mach number of 0.475. The tests were made primarily to determine the effect of speed on the action of this type of aileron. The balance-nose radii of the aileron were varied from 0 to 0.02 of the airfoil chord and the gap width was varied from 0.0005 to 0.0107 of the airfoil chord. Tests were also made with the gap sealed" (p. 1).

Report presenting an investigation in the 7- by 10-foot tunnel of various modifications of the trailing-edge portion of a 0.20-chord plain aileron on a partial-span model of a tapered low-drag wing. The modifications tested included various amounts of symmetrical and unsymmetrical thickening and beveling of the aileron trailing edge. Results regarding coefficients and corrections, characteristics with ailerons neutral, characteristics with ailerons deflected, aileron trim characteristics, and estimated aileron-control characteristics are provided.

Report presenting force tests in two-dimensional flow made on an NACA 66-009 airfoil with a flap having a chord 30 percent of the airfoil chord and a tab having a chord 20 percent of the flap chord. A plain flap and flaps having overhangs of 35 and 50 percent of the flap chord were tested with two gap variations: sealed and unsealed. Results regarding lift, flap hinge moments, pitching moments, drag, and tab characteristics are provided.

Report presenting lift and hinge-moment characteristics of various types of airplane control surface. The data can be used to determine curves correlating the results of many tests of the various types of aerodynamic balance.

Report presenting flight tests of an all-movable vertical tail of reduced area of the Fairchild XR2K-1 airplane. Results are in agreement with previously obtained data on a larger all-movable tail. Results regarding rudder effectiveness, directional stability, rudder-free lateral motion, rudder hinge moments, and areas of future research are provided.

Report presenting tests in the two-dimensional low-turbulence pressure tunnel to study the interference effects of various pusher-propeller shaft-housing combinations on a low-drag airfoil. Thirty different combinations were tested, variations being made in shaft size, shape, angle, and fillet.

Report presenting an investigation in the 7- by 10-foot tunnel of three inset tabs and of one attached tab on the beveled aileron of a low-drag wing. The results indicated that, of the arrangements tested, an inset tab with a chord 50 percent of the aileron chord provided the most satisfactory trimming characteristics on a beveled aileron.

From Summary: "Tests were made of an 0.309-chord double-slotted flap on an NACA 65, 3-118, a equals 1.0 airfoil section to determine drag, lift, and pitching-moment characteristics for a range of flap deflections. Results indicate that combination of a low-drag airfoil and a double-slotted flap, of which the two parts moved as a single unit, gave higher maximum lift coefficients than have been obtained with plain, split, or slotted flaps on low-drag airfoils. Pitching moments were comparable to those obtained with other high-lift devices on conventional airfoils for similar lift coefficients."

Report presenting an analysis of the pressure drop that is required to cool a typically baffled radial engine, which shows that a total pressure drop of 58 pounds per square foot is necessary at sea level and 112 pounds per square foot is required at an altitude of 40,000 feet.

Report presenting an investigation of the effects on stability and control of a pusher propeller behind conventional horizontal and vertical tail surfaces in the free-flight tunnel by tests of a scale model of a submerged-engine pusher airplane. The investigation consisted of flight and balance tests at windmilling and high-power conditions with a partial-span Zap extensible flap extended and retracted. Results regarding the longitudinal stability, longitudinal control, stalling characteristics, lateral stability, and lateral control are provided.

"The effect of variations in the type of mean line on the section characteristics of several representative NACA low-drag airfoils was investigated. The test results are compared with theoretical predictions and indicate trends that facilitate the choice of mean line in the absence of tests" (p. 1).

Report presenting an investigation that is part of a research program to obtain structures suitable for low-drag wings. The purpose of this particular investigation was to study the drag characteristics of an NACA 66(215)-(1.25)16 airfoil specimen of two-spar construction with hat-section chordwise stiffeners after a compressive load comparable with the maximum applied flight load of a modern military airplane has been applied and removed. Results regarding the variation of section drag coefficient with Reynolds number for the wing specimen of the airfoil, variation of section drag coefficient with section lift coefficient, and drag coefficients at specified Reynolds numbers are provided.

Report presenting compressibility phenomena under flight conditions on the XF2A-2 airplane, which was subjected to a series of dives and pull-outs at speeds up to 550 miles per hour corresponding to Mach numbers of 0.74. Results regarding time histories, pressure data, drag coefficient, and elevator control force are provided.

Report presenting results of flight tests to determine the turning performance of a Navy F2A-3 airplane over a range of speeds for three flap deflections at two altitudes. The results are correlated with an analytical study of turning performance in which the effect of thrust on maximum lift coefficient was considered.

Report presenting testing of models of medium-bomber designs to investigate the relative characteristics of thickened wing roots with propeller-shaft fairings and wings with nacelles. Incremental drag coefficients due to thickened wing roots and due to propeller-shaft fairings through a range of Mach numbers at lift coefficient 0.10. Results regarding force tests, pressure-distribution tests, effect of thickening and filleting, nacelles and propeller-shaft fairings, and a comparison of submerged engines and engine-nacelle combinations are provided.

From Summary: "Surveys of the air flow in the region of the tail surfaces of a single-engine pursuit-type airplane equipped with dual-rotating propellers are presented."

Report presenting a thermal ice-prevention system for the B-24D airplane. The report includes a description of the design and an outline of the method of design analysis. Results of performance tests of the installation will be presented in a supplementary report.