Report discussing the speed distribution in a laminar boundary layer on the surface of an elliptic cylinder, of major and minor axes 11.78 and 3.98 inches, respectively, has been determined by means of a hot-wire anemometer. The direction of the impinging air stream was parallel to the major axis. Special attention was given to the region of separation and to the exact location of the point of separation. An approximate method, developed by K. Pohlhausen for computing the speed distribution, the thickness of the layer, and the point of separation, is described in detail; and speed-distribution curves calculated by this method are presented for comparison with experiment.

From Summary: "A description of the test methods used at the National Bureau of Standards for determining the characteristics of aircraft compasses is given. The methods described are particularly applicable to compasses in which mineral oil is used as the damping liquid. Data on the viscosity and density of certain mineral oils used in United States Navy aircraft compasses are presented. Results of flight tests are presented."

From Introduction: "The present report presents the results of such an analysis as regards the longitudinal-stability and control characteristics of the various airplanes tested."

"This report presents a discussion of longitudinal stability in gliding flight together with a series of charts with which the stability characteristics of any airplane may be readily estimated. The relationships governing stability characteristics are derived from equations of equilibrium referred to moving axes that are tangent and perpendicular to the instantaneous flight path. It is shown that instability of the motion can arise only through an increase of linear and angular momentum in the system during one complete cycle" (p. 289).

From Introduction: "An analytical method for estimating turbine performance from angles and flow areas was therefore developed at the NACA Lewis laboratory in 1947 and is described herein."

From Introduction: "This report is concerned with the presentation of planning data in a form that facilities direct application to the initial stage of design."

From Introduction: "The present paper is restricted to a discussion of wing theory subject to the assumptions of linearized compressible flow. It therefore employs solutions of Laplace's equation and the wave equation for cases where the boundary condition are specified in the plane of the wing."

From Summary: "A number of calculations of bending-torsion wing flutter are made at two Mach numbers, m=0 (incompressible case) and m=0.7, and results are compared. The air forces employed for the case of m=0.7 are based on Frazer's recalculation of Possio's results, which are derived on the assumption of small disturbances to the main flow. For ordinary wings of normal density and of low bending frequency in comparison with torsion frequency, the compressibility correction to the flutter speed appears to be of the order of a few percent; whereas the correction to flutter speed for high-density wing sections, such as propeller sections, and to the wing-divergence speed in general, may be based on a rule using the (1 - m(2))1/4 factor and, for m=0.7, represents a decrease of the order of 17 percent."

Approximate shapes of nonlifting bodies having minimum pressure foredrag at high supersonic airspeeds are calculated. With the aid of Newton's law of resistance, the investigation is carried out for various combinations of the conditions of given body length, base diameter, surface area, and volume. In general, it is found that when body length is fixed, the body has a blunt nose; whereas, when the length is not fixed, the body has a sharp nose. The additional effect of curvature of the flow over the surface is investigated to determine its influence on the shapes for minimum drag. The effect is to increase the bluntness of the shapes in the region of the nose and the curvature in the region downstream of the nose. These shape modifications have, according to calculation, only a slight tendency to reduce drag. Several bodies of revolution of fineness ratios 3 and 5, including the calculated shapes of minimum drag for given length and base diameter and for given base diameter and surface area, were tested at Mach numbers from 2.73 to 6.28. A comparison of theoretical and experimental foredrag coefficients indicates that the calculated minimum-drag bodies are reasonable approximations to the correct shape.

A method is presented for calculating the aerodynamic loading, the divergence speed, and certain stability derivatives of swept and unswept wings and tail surfaces of arbitrary stiffness. Provision is made for using either stiffness curves and root rotation constants or structural influence coefficients in the analysis. Computing forms, tables of numerical constants required in the analysis, and an illustrative example are included to facilitate calculations by means of the method.

An investigation of a large group of related airfoils was made in the NACA variable-density wind tunnel at a large value of the Reynolds number. The tests were made to provide data that may be directly employed for a rational choice of the most suitable airfoil section for a given application. The variation of the aerodynamic characteristics with variations in thickness and mean-line form were systematically studied. (author).

From Summary: "Long-range hypervelocity vehicles are studied in terms of their motion in powered flight. Powered flight is analyzed for an idealized propulsion system which approximates rocket motors. Unpowered flight is characterized by a return to earth along a ballistic, skip, or glide trajectory. Only those trajectories are treated which yield the maximum range for a given velocity at the end of powered flight. Aerodynamic heating is treated in a manner similar to that employed previously by the senior authors in studying ballistic missiles (NACA rep. 1381), with the exception that radiant as well as convective heat transfer is considered in connection with glide and skip vehicles."

"This report presents the results of tests made on three sizes of roots type aircraft engine superchargers. The impeller contours and diameters of these machines were the same, but the length were 11, 8 1/4, and 4 inches, giving displacements of 0.509, 0.382, and 0.185 cubic foot per impeller revolution. The information obtained serves as a basis for the examination of the individual effects of impeller speed and displacement on performance and of the comparative performance when speed and displacement are altered simultaneously to meet definite service requirements" (p. 3).

This report presents the tests results of a series of tests made of the sprays from 14 fuel injection nozzles of 9 different types, the sprays being injected into air at atmospheric density and at 6 and 14 times atmospheric density. High-speed spark photographs of the sprays from each nozzle at each air density were taken at the rate of 2,000 per second, and from them were obtained the dimensions of the sprays and the rates of spray-tip penetration. The sprays were also injected against plasticine targets placed at different distances from the nozzles, and the impressions made in the plasticine were used as an indication of the distribution of the fuel within the spray. Cross-sectional sketches of the different types of sprays are given showing the relative sizes of the spray cores and envelopes. The characteristics of the sprays are compared and discussed with respect to their application to various types of engines.

"An investigation of the three important factors that determine convective heat-transfer characteristics at supersonic speeds, location boundary-layer transition, recovery factor, and heat-transfer parameter has been performed at Mach numbers from 1.49 to 1.18. The bodies of revolution that were tested had, in most cases, laminar boundary layers, and the test results have been compared with available theory. Boundary-layer transition was found to be affected by heat transfer" (p. 1301).

This report presents the results of cooling tests conducted on a calibrated GR-1535 Pratt and Whitney Wasp, Jr. Engine installed in a Vought X04U-2 airplane. The tests were made in the NACA full-scale tunnel at air speeds from 70 to 120 miles per hour, at engine speeds from 1,500 to 2,600 r.p.m., and at manifold pressures from 19 to 33 inches of mercury absolute. A Smith controllable propeller was used to facilitate obtaining the different combinations of engine speed, power, and manifold pressure.

Transonic similarity rules are applied to the correlation of experimental data for a series of related rectangular wings of varying aspect ratio, thickness, and camber. The data correlation is presented in two parts: the first part presents the correlation for a series of 22 wings having symmetrical NACA 63a-series sections; the second part is concerned with a study of one type of camber by correlation of the data for a series of 18 cambered wings having NACA 63a2xx and 63a4xx sections.

A method is derived for calculating the damping coefficients in pitch and roll for a series of triangular wings and a restricted series of sweptback wings at supersonic speeds. The elementary "supersonic source" solution of the linearized equation of motion is used to find the potential function of a line of doublets, and the flows are obtained by surface distributions of these doublet lines. The damping derivatives for triangular wings are found to be a function of the ratio of the tangent of the apex angle to the tangent of the Mach angle. As this ratio becomes equal to and greater than 1.0 for triangular wings, the damping derivatives, in pitch and in roll, become constant. The damping derivative in roll becomes equal to one-half the value calculated for an infinite rectangular wing, and the damping derivative in pitch for pitching about the apex becomes equal to 3.375 times that of an infinite rectangular wing.

The loss of strength of cast polymethyl methacrylate plastic as a result of crazing is of considerable importance to the aircraft industry. Because of the critical need for basic information on the nature of crazing and the effects of various treatments and environmental conditions on its incidence and magnitude, an investigation of this phenomenon was undertaken. The following factors were examined: (1) the effect of stress-solvent crazing on tensile strength of polymethyl methacrylate; (2) the critical stress and strain for onset of crazing at various temperatures; (3) the effect of molecular weight on crazing; and (4) the effect of multiaxial stretching on crazing of polymethyl methacrylate and other acrylic glazing materials.

"This report gives the results of the second portion of an investigation in the twenty-foot Propeller Research Tunnel of the National Advisory Committee for Aeronautics, on the cowling and cooling of a "Whirlwind" J-5 radial air-cooled engine. The first portion pertains to tests with a cabin fuselage. This report covers tests with several forms of cowling, including conventional types, individual fairings behind the cylinders, individual hoods over the over the cylinders, and the new N. A. C. A. complete cowling, all on an open cockpit fuselage. Drag tests were also made with a conventional engine nacelle, and with a nacelle having the new complete cowling" (p. 191).

"An investigation of the corrosion of light metal alloys used in aircraft was begun at the National Bureau of Standards in 1925 and has for its purpose causes of corrosion in aluminum-rich and magnesium-rich alloys together with the development of methods for its prevention. The results, obtained in an extensive series of laboratory and weather-exposure tests, reveal the relative durability of a number of commercially available materials and the extent to which the application of various surface coatings of oxide alone and with paint coatings afforded additional protection. The paper may be considered as a supplement to NACA report 490" (p. 395).

Report presents the results of an investigation of the effects of ground interference on the aerodynamic characteristics of a 42 degree sweptback wing at distances 0.68 and 0.92 of the mean aerodynamic chord from the simulated ground to the 0.25-chord point of the mean aerodynamic chord. Survey data behind the wing, both with and without the simulated ground, are presented in the form of contour charts of downwash, sidewash, and dynamic-pressure ratio at longitudinal stations of 2.0 and 2.8 mean aerodynamic chords behind the wing.

"An investigation has been conducted in the Langley stability tunnel on a vertical-tail model with a stub fuselage in combination with various horizontal tails to determine the effect of horizontal-tail span and vertical location of the horizontal tail relative to the vertical tail on the aerodynamic characteristics of an unswept tail assembly in sideslip. The results of the investigation indicated that the induced loading carried by the horizontal tail produced a rolling moment about the point of attachment to the vertical tail which was strongly influenced by horizontal-tail span and vertical locations. The greatest effect of horizontal-tail span on the rolling-moment derivative of the complete tail assembly was obtained for horizontal-tail locations near the top of the vertical tail" (p. 351).

"Test data and analysis show that the rate of fuel leakage between a lapped plunger and sleeve varies directly with the density of the fuel, the diameter of the plunger, the pressure producing the leakage, and the cube of the mean clearance between the plunger and sleeve. The rate varies inversely as the length of the lapped fit and the viscosity of the fuel. With a mean clearance between the plunger and sleeve of 0.0001 inch the leakage amounts to approximately 0.2 percent of the fuel injected with gasoline and as low as 0.01 percent with diesel fuel oils" (p. 63).